Sony VPL-HS10 / VPLL-CT10 / VPLL-CW10 Service Manual ▷ View online
1-10
VPL-HS10
1-2-11. Extension Board and EXtension Connectors
X1 board
X4 board
X3 board
X5 board
X7 board
X6 board
X2 board
X2 board
X3 board
SR connector assy (12P)
ZH connector assy (7P)
ZH connector assy (8P)
ZH connector assy (10P)
ZH connector assy (9P)
Three flat connectors assy (32P)
SR connector assy (5P)
SR connector assy (3P)
Two PH connectors assy (3P)
ZH connector assy A (3P)
ZH connector assy B (3P)
SR connector assy (2P)
ZH connector assy (4P)
SR connector assy (4P)
X kit assy (A-1604-096-A)
Eight flat connectors assy (50P)
1-11
VPL-HS10
1-2-12. Extension Board and Extension Connectors Connection
X1
G
C
B
X4
X6
QB
QA
NF
NR
L
DC fan
DC fan
X3
X3
X2
X2
X7
X5
CN610
CN610
CN110
CN601
CN601
CN101
CN705
CN607
CN771
CN606
CN606
CN501
CN502
CN23
CN22
CN23
CN22
CN33
CN33
CN32
CN32
CN108
CN107
CN110
CN112
CN72
CN73
CN75
CN52
CN111
CN106
CN105
CN106
CN861
CN820
CN820
CN770
CN770
CN860
CN860
CN111
CN112
CN103
CN104
CN604
CN103
CN102
CN902
CN603
CN604
CN603
CN611
CN611
CN609
CN608
CN612
CN109
CN108
CN821
CN706
CN702
CN703
CN605
CN102
CN602
CN602
SR connector assy
(12P)
(12P)
SR connector assy (3P)
SR connector assy (5P)
SR connector assy (2P)
Flat connector assy
(32P)
(32P)
Flat connector assy
(50P)
(50P)
CN609
CN608
CN612
PH connector assy (3P)
PH connector assy (3P)
ZH connector assy
(7P)
(7P)
ZH connector assy (8P)
ZH connector assy A
(3P)
(3P)
ZH connector assy (4P)
ZH connector assy B (3P)
ZH connector assy (9P)
ZH connector assy
(10P)
(10P)
SSR connector assy (4P)
HB
1-12
VPL-HS10
1-2-13. Connection Example
For C Board
Flat connector assy (32P)
Flat connector assy (50P)
Flat connector assy (50P)
Flat connector assy (50P)
Flat connector assy (50P)
Flat connector assy (32P)
Flat connector assy (50P)
X1
X6
X4
C
C
X7
X3
X3
X2
X2
B
B
QA
QB
QB
X7
X7
X6
X4
QA
X1
X6
X4
C
X5
X3
X2
X2
X3
B
QA
QB
X5
X5
For C and B Boards
For B Board
1-13
VPL-HS10
1-3. Service Knowhow
1-3-1. After Replacing the Prism Block
1.
Perform Section “2-2. V COM Adjustment.”
2.
Perform the Gamma data writing of the Prism Block.
3.
Perform Section “2-4. White Balance Adjustment on
Servicing.”
Servicing.”
1-3-2. After Replacing the Board
. Refer to the cross table shown on right.
. There are no need to perform the adjustment when the board
. There are no need to perform the adjustment when the board
other than the B board or C board had been replaced.
1) When Replacing the B Board
When the data before replacement can be read properly
1.
1.
Make a note of the data before replacement. After
replacement, write the data into the new board with
service mode.
replacement, write the data into the new board with
service mode.
2.
If the white balance is extremely deteriorated, perform
the white balance adjustment (Refer to Section 2-4.).
the white balance adjustment (Refer to Section 2-4.).
When the data before replacement cannot be read
1.
1.
Perform Section “2-2. V COM Adjustment.”
2.
Perform Section “2-4. White Balance Adjustment on
Servicing.”
Servicing.”
3.
Perform Section “2-5. Tilt Adjustment.”
2) When Replacing the C Board
1.
Before replacement, unsolder the IC705 from the
replaced C board and then mount it to the new board.
replaced C board and then mount it to the new board.
2.
Perform Section “2-2. V COM Adjustment.”
3.
If the white balance is extremely deteriorated, perform
the white balance adjustment (Refer to Section 2-4.).
the white balance adjustment (Refer to Section 2-4.).
4.
Perform Section “2-5. Tilt Adjustment.”
3) When Replacing the Other Board
There are no need to perform the adjustment.
Cross Table of Board Replacement
Board Name
Device Name
Item Name
B
C
OTHER
TILT C0
*
O
TILT C1
*
O
TILT C2
*
O
P.DRV
VCOM (R)
*
O
VCOM (G)
*
O
VCOM (B)
*
O
W/B ADJUST
INPUT-A HIGH
GAIN R
*
O
GAIN G
*
O
GAIN B
*
O
BIAS R
*
O
BIAS G
*
O
BIAS B
*
O
INPUT-A LOW
GAIN R
*
O
GAIN G
*
O
GAIN B
*
O
BIAS R
*
O
BIAS G
*
O
BIAS B
*
O
INPUT-A HIGH
GAIN R
*
O
GAIN G
*
O
GAIN B
*
O
BIAS R
*
O
BIAS G
*
O
BIAS B
*
O
INPUT-A MID
GAIN R
*
O
GAIN G
*
O
GAIN B
*
O
BIAS R
*
O
BIAS G
*
O
BIAS B
*
O
VIDEO MID
GAIN R
*
O
GAIN G
*
O
GAIN B
*
O
BIAS R
*
O
BIAS G
*
O
BIAS B
*
O
VIDEO LOW
GAIN R
*
O
GAIN G
*
O
GAIN B
*
O
BIAS R
*
O
BIAS G
*
O
BIAS B
*
O
*
: When down the data before replacement, and then
write in the data after the board replacement.
O
: Need adjustment
Value : See description.
Click on the first or last page to see other VPL-HS10 / VPLL-CT10 / VPLL-CW10 service manuals if exist.