DOWNLOAD Sony RM-PJAW15 / VPL-HW10 Service Manual ↓ Size: 269.94 KB | Pages: 16 in PDF or view online for FREE

5

VPL-HW10

. When sending a command from CONTROLLER, the return data from PROJECTOR should be re-

ceived first before sending the next command. Even if the next command is sent before receiving the
return data, since PROJECTOR will not be able to receive that command, it does not return a response
to CONTROLLER. Consequently, no error code is also sent.
The following lists the approximate waiting times for PROJECTOR to return the return data after
CONTROLLER sends the command.

. When a communication error occurs, PROJECTOR ignores the data received until now, and set into the

reception standby state.

. For undefined commands or commends determined as invalid by PROJECTOR, PROJECTOR will

send the “NAK” return data to CONTROLLER .

. Take note that when data is written when the input signal of PROJECTOR is unstable, that data (value)

will not be incorporated.

. When INDEX specified SIRCS direct command is transmitted, leave an interval of 45 msec until the

next transmission. (Do not return the return data (ACK, NAK) when the SIRCS direct command is
received.)

The await-return time is approx. 30 to 1500 msec.

n
This is the case, unless the communications are interfered anyway.

This model is equipped with the protocol that conforms to the Device Discovery stipulated by
AMX.Contact AMX for details about the Device Discovery.

6

VPL-HW10

Input

00h

01h

Video

00h

Set/Get

S Video

01h

Input A

02h

Component

03h

HDMI1

04h

HDMI2

05h

Picture Mode

00h

02h

Dynamic

00h

Standard

01h

Cinema

02h

User1

03h

User2

04h

User3

05h

Contrast

00h

10h

00h to 64h (0 to 100)

Brightness

00h

11h

00h to 64h (0 to 100)

Color

00h

12h

00h to 64h (0 to 100)

Hue

00h

13h

00h to 64h (0 to 100)

Sharpness

00h

14h

Normal

00h to 64h (0 to 100)

ColTemp

00h

17h

High

00h

Mid

01h

Low

02h

Custom1

03h

Custom2

04h

Custom3

05h

Custom4

06h

Lamp Control

00h

1Ah

Low

00h

High

01h

Black Level Adj.

00h

1Ch

Off

00h

Low

01h

High

02h

Advanced Iris

00h

1Dh

Off

00h

On

01h

Auto1

02h

Auto2

03h

Real Color Processing

00h

1Eh

off

00h

User1

01h

User2

02h

User3

03h

Filme Mode

00h

1Fh

Off

00h

Auto

02h

7

VPL-HW10

Wide Mode

00h

20h

Full

00h

Set/Get

Normal

01h

Wide Zoom

02h

Zoom

03h

Full1

07h

Full2

08h

Gamma Correction

00h

22h

Off

00h

Gamma 1

01h

Gamma 2

02h

Gamma 3

03h

Over Scan

00h

23h

Off

00h

On

01h

Screen Area

00h

24h

Full

00h

Through

01h

NR

00h

25h

Off

00h

Low

01h

Middle

02h

High

03h

Block NR

00h

26h

Off

00h

Low

01h

Middle

02h

High

03h

Mosquito NR

00h

27h

Off

00h

Low

01h

Middle

02h

High

03h

Picture Muting

00h

30h

Off

00h

On

01h

Input-A Signal Sel

00h

32h

Auto

00h

Computer

01h

Component

02h

Video GBR

03h

Color Space

00h

3Bh

Normal

00h

Wide

01h

USER GAIN RED

00h

50h

FFE2h to 001Eh (

_30 to 30)

USER GAIN GREEN

00h

51h

FFE2h to 001Eh (

_30 to 30)

USER GAIN BLUE

00h

52h

FFE2h to 001Eh (

_30 to 30)

USER BIAS RED

00h

53h

FFE2h to 001Eh (

_30 to 30)

USER BIAS GREEN

00h

54h

FFE2h to 001Eh (

_30 to 30)

USER BIAS BLUE

00h

55h

FFE2h to 001Eh (

_30 to 30)

8

VPL-HW10

Iris Sensitivity

00h

56h

Recommend

00h

Set/Get

Fast

01h

Slow

02h

Iris Manual

00h

57h

00h to 64h (0 to 100)

xvColor

00h

5Ah

Off

00h

On

01h

Status Error

01h

01h

NO ERROR

00h

Get only

LAMP ERROR

01h

FAN ERROR

02h

COVER ERROR

04h

TEMP ERROR

08h

D5V ERROR

10h

POWER ERROR

20h

NVM Data ERROR

80h

Status Power

01h

02h

STANBY

00h

START UP

01h

STARTUP LAMP

02h

POWER ON

03h

COOLING1

04h

COOLING2

05h

SAVING COOLING1

06h

SAVING COOLQØG2

07h

SAVING STABY

08h

Lamp Timer

01h

13h

USE TIME

0000h-FFFFh 

*1

Sircs (15bit category)

17h

Refer to Table4

-----

00h

00h

Set only 

*2

Sircs (20bit category)

19h

Refer to Table5

-----

00h

00h

*1 Example) In case the lamp timer indicates 1000H, return values are [03h] upper byte and [E8h] lower byte.
*2 It is corresponded to single command only.