DOWNLOAD Sony DPP-FP60 / DPP-FP60BT Service Manual ↓ Size: 752.7 KB | Pages: 26 in PDF or view online for FREE

AEP Model

UK Model

E Model

Australian Model

East European Model

Russian Model

Korean Model

2008J0200-1

  ©2008.10

DPP-FP60/FP60BT

Revised-1

Replace the previously issued
SERVICE MANUAL 9-852-188-11
with this Manual.

— 2 —

DPP-FP60/FP60BT

These specifications are extracted from Operating
Instructions of DPP-FP60/FP60BT (3-197-729-11).

6 400 (H) x 4 800 (V) dots
(Excluding Index Print and part of
Creative Print)

9 999 files for a memory card/an
external device

See supplied “Read This First”.

LCD panel:

5.0 cm (2.0 type) TFT drive

Total number of dots:

86 636 (358 x 242)

DC IN jack, DC 24V

While printing: 75 W (maximum)
On standby mode: less than 1W

5 

°C to 35 °C (41 °F to 95 °F)

Approx. 175 x 60 x 137 mm
(7 

 

x 2 

3

/

8

 x 5 

1

/

2

 inches)

(w/h/d, excluding protruding parts)
(304 mm (12 inches) of depth when the
paper tray is installed.)

 Approx.  1.1 kg (2 lb 7 oz)
(excluding the paper tray, ink ribbon,
AC power adaptor)

See page 2-4E.

x AC power adaptor AC-S2425

x Bluetooth USB adaptor DPPA-BT1

AC 100V to 240 V, 50/60 Hz,
1.5A to 0.75 A

DC 24 V, 2.2 A (Peak 3.7 A, 6.5 s)

x Printer

Dye sublimation printing  (Yellow/
Magenta/Cyan 3 pass)

300 (H) x 300 (V) dpi

256 levels processing (8 bits for each
Yellow/Magenta/Cyan),
approx. 16 770 000 colors

P (Post Card/4 x 6 inch) size:

101.6 x 152.4 mm (maximum,
borderless)

Memory card

*1*2*3*4

:

Approx. 63 sec.

PictBridge

*3*5

:

Approx. 71 sec.

Via PC

*6

:

Approx. 60 sec.

USB for PC connection USB 1.1 (Type B)

High speed is not supported.

PictBridge connector

“

Memory Stick” insertion slot

SD Card insertion slot

JPEG: DCF 2.0 compatible, Exif

 

 2.21

compatible, JFIF

*7

TIFF:

Exif 2.21 compatible

BMP

*8

: 1, 4, 8, 16, 24, 32 bits Windows

format

Some image file formats are not
compatible.

Bluetooth Specification Version 2.0 + EDR

Bluetooth power class 2

ISM band 2 402 to 2 480 MHz

Line-of-sight distance: Approximately 10 
m*/ Interference distance: Approximately 
20 m or shorter (*This distance may vary 
depending on the following conditions: 
obstacles between devices, signal quality, 
magnetic fields, static electricity and 
electromagnetic interference, software, 
operating system, reception sensitivity, and 
antenna performances.)

5 

°C to 35 °C (41 °F to 95 °F)

Approx. 60 x 30.5 x 122 mm
(2 

3

/

8

  x 1 

1

/

4

 x 4 

7

/

8

 inches)

(w/h/d, excluding protruding parts
and cables)

Approx.  305 g (11 oz)

Design and specifications are subject to
change without notice.

* The total number of sheets of P size print paper

that the printer can print is estimated to be
approximately 2,000.

*1:

Print Settings: Borderless, No time stamp,
AutoFine Print 3: ON (Photo)

*2:

When printing a photo (3.11 MB file size)
taken by a Sony digital still camera
containing effective picture elements of
approximately 7,200,000 or equivalent.

*3:

Print Speed: Time from when the PRINT
button is pressed to when printing is
finished. (The printing time may vary
depending on a used equipment, a format
of an image, a used memory card, settings
of an application and operating conditions.)

*4:

When printing from a “Memory Stick PRO
Duo” inserted in the printer’s slot

*5:

When printing via DSC-T30 connected by
USB cable. Time from when the “PRINT”
button on the OSD of the camera is pressed
to when the printing is finished.

*6:

The time for data processing and
transferring is excluded.

*7:

Baseline JPEG with 4:4:4, 4:2:2, or 4:2:0
format

*8:

You cannot print using the Picture Motion
Browser.

— 3 —

DPP-FP60/FP60BT

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

0

0

— 4 —

DPP-FP60/FP60BT

1-1.

LID UPPER SECTION ··················································· 1-2

1-2.

PRINTER SECTION ······················································ 1-3

2-1.

EXPLODED VIEWS ······················································ 2-2

3-1.

ELECTRICAL TROUBLESHOOTING ························· 3-1

3-2.

MECHANICAL TROUBLESHOOTING ······················· 3-2

······························· 4-1

4-1.

SERVICE MODE ···························································· 4-2

4-2.

ADJUSTMENT ······························································· 4-3

4-3.

CHECK ··········································································· 4-5