DOWNLOAD Sony DPP-FP35 Service Manual ↓ Size: 410.54 KB | Pages: 9 in PDF or view online for FREE

US Model

Canadian Model

AEP Model

UK Model

E Model

Australian Model

East European Model

Russian Model

Korean Model

2006F1600-1

  ©2006.06

DPP-FP35

When the parts other than those described in “2. Repair Parts List”

need replacement, replace the unit.

— 2 —

DPP-FP35

x

AC 100 to 240 V, 50/60 Hz, 1.5 to
0.75 A

DC 24 V, 2.2 A

5 ˚C to 35 ˚C (41 ˚F to 95 ˚F)

Approx. 60 x 30.5 x 122 mm
(2 

3

/

8

  x 1 

1

/

4

 x 4 

7

/

8

 inches)

(w/h/d, excluding protruding parts)

Approx.  300 g (11 oz)

Design and specifications are subject to
change without notice.

*1:

When the 16 x 16 matrix is used: 300 x 16 =
4,800 dpi

*2:

When the 12.7 x 12.7 matrix is used: 300 x
12.7 = 3,810 dpi

*3:

When photo of 3.11MB file size is taken by
DSC-T30 (7Mega Cyber-shot)

*4:

Time from when the print button on the
display window of the camera is pressed to
when printing is finished via DSC-T30
connected by USB cable.

*5:

The time for data processing and
transferring is excluded.

*6:

Baseline JPEG with 4:4:4, 4:2:2, or 4:2:0
format

10 000(H) x 7 500(V) dots

See “Preparing the print pack”.

DC IN jack, DC 24 V
(On standby mode, less than 1W)

5 ˚C to 35 ˚C (41 ˚F to 95 ˚F)

Approx. 175 x 60 x 137 mm
(7 x 2 

3

/

8

 x 5 

1

/

2

 inches)

(w/h/d, excluding protruding parts)
(306 mm (12 

1

/

8

 inches) of depth when

the paper tray is installed.)

Approx.  1 kg (2 lb 3 oz)
(excluding the paper tray, print
cartridge, AC power adaptor)

See page 1-3E.

x

Dye sublimation printing  (Yellow/
Magenta/Cyan 3 pass)

300 (H) x 300 (V) dpi
Equivalent to
3 color Ink-Jet 4800 dpi x 4800 dpi 

*1

6 color Ink-Jet 3810 dpi x 3810 dpi 

*2

256 levels (8 bits for each Yellow/
Magenta/Cyan), approx. 16 770 000
colors

Post Card (4 x 6 inch/10 x 15 cm) size:

101.6 x 152.4 mm (maximum,
borderless)

PictBridge mode

*4

: Approx. 77 seconds

PC mode

*5

: Approx. 60 seconds

USB for PC connection USB 1.1
(Type B)

Highspeed is not supported.

PictBridge connector

JPEG: DCF 2.0 compatible, Exif

 

 2.21

compatible, JFIF

*6

Some image file formats are not
compatible.

These specifications are extracted from Operating
Instructions of DPP-FP35 (2-682-260-11 (2)).

— 3 —

DPP-FP35

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40

°

C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350

°

C.

Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.

LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

— 4 —

DPP-FP35

························································ 1-1

2-1.

EXPLODED VIEWS ······················································ 2-2