Sony DPF-V1000N / DPF-X1000N Service Manual ▷ View online
– 5 –
DPF-V1000N/X1000N
1-2.
FRONT CASE SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
1-802-853-11 LCD MODULE (V1000N)
52
A-1701-076-A DCI-001 PC BOARD ASSY
53
A-1708-637-A SERVICE, INV-003 PC BOARD ASSY
54
A-1738-401-A FRONT CASE ASSY SERVICE (V1000N: BLACK)
54
A-1738-402-A FRONT CASE ASSY SERVICE (V1000N: WHITE)
54
(Note)
FRONT CASE ASSY SERVICE (X1000N)
55
4-642-229-01 TAPPING (B 2X)
56
2-666-551-21 SCREW, TAPPING, P2
* 57
4-138-668-01 HIMELON, TAPE L30
58
4-140-552-01 TAPPING (B2X8), SCREW (0+P3)
59
A-1708-638-A SERVICE, MAI-007 PC BOARD ASSY (V1000N)
59
A-1708-639-A SERVICE, MAI-007 PC BOARD ASSY (X1000N)
* 60
4-138-668-11 HIMELON, TAPE L30
61
3-080-205-31 SCREW, TAPPING, P2
62
4-143-337-01 TAPPING (B2X5), SCREW
63
3-080-204-11 SCREW, TAPPING, P2
* 64
4-139-057-01 CONDUCTIVE, TAPE C
X1000N Only
Note: In case of the LCD Panel assy failure, contact
Note: In case of the LCD Panel assy failure, contact
your local Sony service Headquarter for the
measures.
measures.
51
57
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
V1000N
X1000N
V1000N
ns
ns
ns
ns
54
(Note)
55
52
53
61
59
ns
ns
ns
A
A
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
55
55
58
58
55
55
62
64
56
56
ns
(including LCD)
(including LCD)
63
60
– 6 –
DPF-V1000N/X1000N
1-3.
ACCESSORIES
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number
specified.
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
AC Adaptor
(AC-DPF200)
(AC-DPF200)
0
1-487-176-12
Remote Control
(RMT-DPF2)
(RMT-DPF2)
1-487-173-11
Card Slot Cover
4-118-544-01 (BLACK, WOOD)
4-118-544-11 (WHITE)
4-118-544-11 (WHITE)
Connector Cover
4-117-915-01 (BLACK, WOOD)
4-117-915-11 (WHITE)
4-117-915-11 (WHITE)
Stand
4-117-876-11
Operating Instructions
4-155-758-11 (ENGLISH)
4-155-758-21 (FRENCH)
4-155-758-31 (GERMAN)
4-155-758-41 (DUTCH)
4-155-758-51 (ITALIAN)
4-155-758-61 (SPANISH)
4-155-758-71 (PORTUGUESE)
4-155-758-81 (RUSSIAN)
4-155-758-91 (UKRAINIAN)
4-155-758-21 (FRENCH)
4-155-758-31 (GERMAN)
4-155-758-41 (DUTCH)
4-155-758-51 (ITALIAN)
4-155-758-61 (SPANISH)
4-155-758-71 (PORTUGUESE)
4-155-758-81 (RUSSIAN)
4-155-758-91 (UKRAINIAN)
Read This First
4-155-759-11 (ENGLISH)
4-155-759-21 (FRENCH)
4-155-759-31 (GERMAN)
4-155-759-41 (DUTCH)
4-155-759-51 (ITALIAN)
4-155-759-61 (SPANISH)
4-155-759-71 (PORTUGUESE)
4-155-759-81 (RUSSIAN)
4-155-759-91 (UKRAINIAN)
4-155-759-21 (FRENCH)
4-155-759-31 (GERMAN)
4-155-759-41 (DUTCH)
4-155-759-51 (ITALIAN)
4-155-759-61 (SPANISH)
4-155-759-71 (PORTUGUESE)
4-155-759-81 (RUSSIAN)
4-155-759-91 (UKRAINIAN)
AC Power Cord
0
1-827-269-31 (UK)
0
1-827-826-41 (AEP, EE, RUS)
– 7 –
DPF-V1000N/X1000N
2-1.
METHOD OF WRITING AND UPGRADE
OF FIRMWARE
OF FIRMWARE
Note:
Download the firmware from the homepage of ESI.
Writing of firmware
Execute writing the latest firmware when exchange the “SERVICE,
MAI-007 PC BOARD ASSY”.
If the firmware is not written, normal operation is not done.
MAI-007 PC BOARD ASSY”.
If the firmware is not written, normal operation is not done.
Procedure
1. Download the firmware from the homepage of ESI.
2. Decompress the zip file and copy the entire \SONY folder con-
2. Decompress the zip file and copy the entire \SONY folder con-
taining the firmware onto the root directory (most significant
hierarchy) of the Memory Stick.
(make sure that the .bin file is in \SONY\DPFSV folder.)
hierarchy) of the Memory Stick.
(make sure that the .bin file is in \SONY\DPFSV folder.)
3. Install Memory Stick in the Memory Stick slot of this unit
before turning on the power supply.
4. Connect AC adaptor (AC-DPF200) of accessories with this
unit.
5. Turn on the [Power Switch] while pushing the [VIEW MODE]
button of the main unit.
6. Release the buttons when a version up screen is displayed.
7. Confirm access LED changes into lighting after a few min-
7. Confirm access LED changes into lighting after a few min-
utes.
(End of upgrade.)
(End of upgrade.)
8. Turn off power pushing the power button. (keeps pushing for
about one second.)
9. Remove Memory Stick from this unit.
10. Push the power button while pushing the [MENU] button and
10. Push the power button while pushing the [MENU] button and
the [ENTER] button. (The service mode starts.)
11. Release the buttons if an initial screen of the service mode is
displayed in LCD.
12. Confirm the figure of “CHECKSUM” (hexadecimal number)
is the same as the version of the firmware that has been de-
scribed in the homepage of ESI.
scribed in the homepage of ESI.
13. Turn off power pushing the power button.
2-2.
CONFIRMATION AFTER UPGRADE
1. Turn on the [Power Switch] while pushing the [MENU] but-
ton and the [ENTER] button. (The service mode starts.)
2. Release the buttons if an initial screen of the service mode is
displayed in LCD.
1) Confirm the figure of “CHECKSUM” (hexadecimal number)
is the same as the version of the firmware that has been de-
scribed in the homepage of ESI.
scribed in the homepage of ESI.
2) Confirm the destination has not been changed.
(XX of “DPF-V1000N (XX)” or “DPF-X1000N (XX)” in up-
permost screen steps means destination)
permost screen steps means destination)
3) When destination has changed, Change the destination refer-
ring to following “Procedure of the destination change”.
2-3.
PROCEDURE OF THE DESTINATION
CHANGE
CHANGE
1. Turn on the [Power Switch] while pushing the [MENU] but-
ton and the [ENTER] button. (The service mode starts.)
2. Release the buttons if an initial screen of the service mode is
displayed in LCD.
3. Match the cursor to “Select Model” pushing the [
m] button
several times, and push the [ENTER] button.
4. Move the cursor to the destination to be set with [
M], [m],
[
<], [,], button and push the [ENTER] button.
5. Return to the first screen (screen where DPF-V1000N (XX)
or DPF-X1000N (XX) is displayed) pushing the [
M] button
several times, and confirm destination has changed.
6. Turn off power pushing the power button.
SECTION 2
WRITING AND UPGRADE OF FIRMWARE
– 8 –
DPF-V1000N/X1000N
2-4.
INITIALIZATION OF SETTING
Various settings are returned to factory default by initializing the
setting.
Execute this mode when returning the set to the customer.
However, the date setting is maintained.
setting.
Execute this mode when returning the set to the customer.
However, the date setting is maintained.
1. Turn on the [Power Switch] while pushing the [MENU] but-
ton and the [ENTER] button. (The service mode starts.)
2. Release the buttons if an initial screen of the service mode is
displayed in LCD.
3. Match the cursor to “Set Default” pushing the [
m] button sev-
eral times, and push the [ENTER] button.
4. Confirm “OK” display appears at the right of “Set Default”.
5. Turn off power pushing the power button.
5. Turn off power pushing the power button.
2-5.
FORMAT INTERNAL MEMORY
Deletes the content of internal memory.
Note:
•
All the images added to the internal memory will be deleted.
•
Do not format the internal memory by using connection to PC
or other external devices.
or other external devices.
1. Turn on the [Power Switch] while pushing the [MENU] but-
ton and the [ENTER] button. (The service mode starts.)
2. Release the buttons if an initial screen of the service mode is
displayed in LCD.
3. Match the cursor to “Format NAND” pushing the [
m] button
several times, and push the [ENTER] button.
4. Confirm “OK” display appears at the right of “Format NAND”.
5. Turn off power pushing the power button.
5. Turn off power pushing the power button.
Click on the first or last page to see other DPF-V1000N / DPF-X1000N service manuals if exist.