Sony DPF-D92 Service Manual ▷ View online
SERVICE MANUAL
DPF-D92
DIGITAL PHOTO FRAME
US Model
Canadian Model
AEP Model
UK Model
East European Model
Russian Model
E Model
Australian Model
Hong Kong Model
Ver. 1.3 2010.03
SPECIFICATIONS
Sony EMCS Co.
9-852-647-14
2010C0500-1
© 2010.3
Published by Tokai TEC
x
Photo frame
LCD screen
LCD panel:
9.0 inches, TFT active matrix
Total number of dots:
Display aspect ratio
15:9
Effective display area
8.6 inches
LCD backlight life
20,000 hours
(before brightness of the backlight is
(before brightness of the backlight is
reduced to half)
Input/Output connectors
USB connector (TypeB, Hi-Speed USB)
USB A/Bluetooth connector
USB A/Bluetooth connector
(TypeA, Hi-Speed USB)
Slots
“Memory Stick PRO” slot
SD memory card/MMC/
xD-Picture Card slot
CompactFlash card/Microdrive slot
SD memory card/MMC/
xD-Picture Card slot
CompactFlash card/Microdrive slot
Compatible image file formats
JPEG: DCF 2.0 compatible, Exif 2.21
compatible, JFIF
*1
RAW (preview only
*2
): SRF, SR2, ARW
(2.0 or lower version)
(Some image file formats are not
compatible.)
Internal memory capacity
*3
1GB
(Approx. 2,000 images
*4
can be saved.)
When measuring media capacity, 1 GB
equals 1 billion bytes, a portion of
which is used for data management.
equals 1 billion bytes, a portion of
which is used for data management.
Power requirements
DC IN jack, DC 12V
Power consumption
Operating temperature
5
°C to 35 °C (41 °F to 95 °F)
Dimensions
[With the stand spread out]
[When the photo frame is hanging on the
wall]
in operation mode
including the
AC adaptor
AC adaptor
at the maximum load
11.6W
normal mode*
5.5W
* The definition of the normal mode is a status
which allows the performance of a slideshow using
images stored in the internal memory with the
default settings without inserting a memory card or
connecting an external device.
images stored in the internal memory with the
default settings without inserting a memory card or
connecting an external device.
x
AC adaptor
Power requirements
- 100 V to 240 V, 50/60 Hz
0.48 A
0.48 A
Rated output voltage
12 V 1.2 A
Dimensions
Approx. 34
× 72 × 69 mm
(1
3
/
8
× 2
7
/
8
× 2
3
/
4
inches)
(width/height/depth)
(excluding the protruding parts)
(excluding the protruding parts)
Mass
Approx. 110 g (4 oz)
See the label of AC adaptor for more details.
Design and specifications are subject to change
without notice.
without notice.
*1
: Baseline JPEG with 4:4:4, 4:2:2, or 4:2:0 format
*2
: RAW files are displayed as thumbnail preview.
*3
: The capacity is calculated as 1 MB is equivalent to
1 000 000 bytes. The actual capacity is reduced as
files for management and applications are
included. Approximately 900MB can be used for
your actual operation.
files for management and applications are
included. Approximately 900MB can be used for
your actual operation.
*4
: Approximate number is shown when the images
taken by 2 000 000 pixels equivalent camera are
saved. The value may vary depending on the
shooting condition.
saved. The value may vary depending on the
shooting condition.
1,152,000
(800
(800
× 3(RGB) × 640) dots
Maximum number of pixels that can be
displayed
displayed
8,000 (H)
× 6,000 (V) pixels
File system
FAT12/16/32,
sector size of 2,048 bytes or smaller
Mass
(excluding the AC adaptor)
Image file name
DCF format, 256 characters, within 8th
hierarchy
Maximum number of files that can be
handled
handled
9,999 files for a memory card/an external
device
Included accessories
• Digital photo frame
• Stand
• Remote control
• AC adaptor
• Operating Instructions
• Read This First
• Warranty
(In some regions, the warranty is not
supplied.)
Approx. 276
× 189 × 144.1 mm
(10
7
/
8
× 7
1
/
2
× 5
3
/
4
inches)
(width/height/depth)
(width/height/depth)
Approx. 276
× 189 × 39.5 mm
(10
7
/
8
× 7
1
/
2
× 1
9
/
16
inches)
Approx. 810 g (1 lb 12
5
/
8
oz)
RMT-DPF3
DPF-D92
Revised-3
Replacement of the previously issued
SERVICE MANUAL 9-852-647-13
with this manual.
SERVICE MANUAL 9-852-647-13
with this manual.
– 2 –
DPF-D92
MAIN FEATURES
The Sony DPF-D92 is a digital photo frame for easily displaying
images taken with a digital camera or other device without using a
computer.
x
images taken with a digital camera or other device without using a
computer.
x
Support for various memory cards
*
Supports various memory cards and other devices, such as a
“Memory Stick”, CompactFlash card, SD memory card, xD-
Picture Card, and USB memory. Just insert a memory card re-
moved from a digital camera or other device, and you will be
able to view the images immediately.
“Memory Stick”, CompactFlash card, SD memory card, xD-
Picture Card, and USB memory. Just insert a memory card re-
moved from a digital camera or other device, and you will be
able to view the images immediately.
x
Various display functions
You can enjoy various viewing modes, such as the slideshow
display, Clock and calendar display, Single view mode, and
Index image display.
display, Clock and calendar display, Single view mode, and
Index image display.
x
Various modes
The displayed image can be switched automatically as though
you are turning the pages of an album yourself. You can select
from various modes, including just images, a clock, or calen-
dar view. You can also change playback settings such as the
playback order.
you are turning the pages of an album yourself. You can select
from various modes, including just images, a clock, or calen-
dar view. You can also change playback settings such as the
playback order.
x
Adding images to internal memory
The images you add to the album are saved in internal memory.
1. Check the area of your repair for unsoldered or poorly-sol-
dered connections. Check the entire board surface for solder
splashes and bridges.
splashes and bridges.
2. Check the interboard wiring to ensure that no wires are
“pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transis-
tors, that were installed during a previous repair. Point them
out to the customer and recommend their replacement.
out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and recom-
mend their replacement.
mend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when solder-
ing or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
• Unleaded solder melts at a temperature about 40
°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur
such as on IC pins, etc.
ordinary solder so use caution not to let solder bridges occur
such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE WITH
MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE
0
SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
x
Exporting images
You can export images in the album to your memory card.
x
Search function
You can search for images by the date, folder, image direction,
and mark.
and mark.
x
Alarm function
The photo frame announces the specified time on the image
and using sound.
and using sound.
x
Automatic rotation of images
The photo frame automatically rotates images to their proper
orientation. Images are also automatically rotated when the
photo frame is set in either the portrait or landscape position.
orientation. Images are also automatically rotated when the
photo frame is set in either the portrait or landscape position.
x
Easy transfer of images taken with a Bluetooth
compatible mobile phone or other device
compatible mobile phone or other device
*
You can transfer images to the photo frame's internal memory
from a Bluetooth compatible device via a Bluetooth adaptor
(optional).
from a Bluetooth compatible device via a Bluetooth adaptor
(optional).
x
Displaying images on a wall
You can hang the photo frame on the wall.
* We do not guarantee proper operations for all types of devices.
– 3 –
DPF-D92
SECTION 1
EXPLODED VIEWS
NOTE:
•
-XX and -X mean standardized parts, so they
may have some difference from the original one.
may have some difference from the original one.
•
Items marked “
∗
” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
should be anticipated when ordering these items.
•
The mechanical parts with no reference number
in the exploded views are not supplied.
in the exploded views are not supplied.
• Abbreviation
AUS : Australian model
CND : Canadian model
EE
CND : Canadian model
EE
: East European model
HK
: Hong Kong model
RUS : Russian model
TW : Taiwan model
The components identified by mark
0
or
dotted line with mark
0
are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0
sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
le numéro spécifié.
1-1.
MAIN SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
A-1710-300-A FRONT FRAME ASSY SERVICE (B) (BLACK)
1
A-1710-520-A FRONT FRAME ASSY SERVICE (T) (BROWN)
2
4-141-801-01 SERVICE LCD
3
4-141-797-01 LCD FRAME SHIEDING_V7
4
2-666-551-21 SCREW, TAPPING, P2
5
4-141-799-01 LIGHT_GUIDE_V7
6
3-080-204-11 SCREW, TAPPING, P2
7
4-148-479-01 SERVICE FFC (LCD)
8
A-1729-548-A MAIN PWB ASSY SERVICE
9
4-141-813-01 TABLE STAND
10
A-1710-309-A REAR CASE ASSY SERVICE
11
3-080-206-21 SCREW, TAPPING, P2
12
4-141-804-01 FUNCTION BUTTON
13
4-141-805-01 BUTTON_5 DIRECTION
14
A-1710-302-A KEY PWB ASSY SERVICE
15
4-148-478-01 SERVICE FFC (KEY)
0 16
4-141-814-01 SERVICE MAIN PWR SW
17
4-141-807-01 SERVICE SD CONNECTOR
18
4-141-808-01 SERVICE MS CONNECTOR
0 19
4-141-809-01 SERVICE DC JACK
20
4-141-810-01 SERVICE USB B CONNECTOR
21
4-141-811-01 SERVICE USB A CONNECTOR
22
4-141-806-01 SERVICE CF CONNECTOR
1
2
3
5
6
7
4
4
4
22
10
11
11
12
13
14
9
4
15
17
18
20
21
19
8
ns
ns
ns
16
Ver. 1.2 2009.06
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
– 4 –
DPF-D92
1-2.
ACCESSORIES
AC Adaptor
0
3-876-557-01 (US, CND)
0
3-876-557-11 (TW)
0
3-876-699-01 (UK, HK)
0
3-876-700-01 (AEP, EE, RUS, E: PAL)
0
3-876-701-01 (AUS)
0
3-876-704-01 (E: NTSC)
Remote Commander
(RMT-DPF3)
(RMT-DPF3)
4-136-608-01
Stand
4-141-813-01
Operating Instructions
4-129-231-12 (ENGLISH) (EXCEPT TW)
4-129-231-22 (FRENCH) (CND, AEP)
4-129-231-32 (GERMAN) (AEP)
4-129-231-42 (DUTCH) (AEP)
4-129-231-52 (ITALIAN) (AEP)
4-129-231-62 (SPANISH) (AEP, E)
4-129-231-72 (PORTUGUESE) (AEP, E)
4-129-231-82 (RUSSIAN) (EE, RUS)
4-129-231-92 (UKRAINIAN) (EE, RUS)
4-129-232-12 (ARABIC) (E)
4-129-232-22 (PERSIAN) (E)
4-129-232-32 (SIMPLIFIED CHINESE) (HK)
4-129-232-42 (TRADITIONAL CHINESE) (HK, TW)
4-129-231-22 (FRENCH) (CND, AEP)
4-129-231-32 (GERMAN) (AEP)
4-129-231-42 (DUTCH) (AEP)
4-129-231-52 (ITALIAN) (AEP)
4-129-231-62 (SPANISH) (AEP, E)
4-129-231-72 (PORTUGUESE) (AEP, E)
4-129-231-82 (RUSSIAN) (EE, RUS)
4-129-231-92 (UKRAINIAN) (EE, RUS)
4-129-232-12 (ARABIC) (E)
4-129-232-22 (PERSIAN) (E)
4-129-232-32 (SIMPLIFIED CHINESE) (HK)
4-129-232-42 (TRADITIONAL CHINESE) (HK, TW)
Read This First
4-129-233-11 (ENGLISH) (EXCEPT TW)
4-129-233-21 (FRENCH) (CND, AEP)
4-129-233-31 (GERMAN) (AEP)
4-129-233-41 (DUTCH) (AEP)
4-129-233-51 (ITALIAN) (AEP)
4-129-233-61 (SPANISH) (AEP, E)
4-129-233-71 (PORTUGUESE) (AEP, E)
4-129-233-81 (RUSSIAN) (EE, RUS)
4-129-233-91 (UKRAINIAN) (EE, RUS)
4-129-234-11 (ARABIC) (E)
4-129-234-21 (PERSIAN) (E)
4-129-234-31 (SIMPLIFIED CHINESE) (HK)
4-129-234-41 (TRADITIONAL CHINESE) (HK, TW)
4-129-233-21 (FRENCH) (CND, AEP)
4-129-233-31 (GERMAN) (AEP)
4-129-233-41 (DUTCH) (AEP)
4-129-233-51 (ITALIAN) (AEP)
4-129-233-61 (SPANISH) (AEP, E)
4-129-233-71 (PORTUGUESE) (AEP, E)
4-129-233-81 (RUSSIAN) (EE, RUS)
4-129-233-91 (UKRAINIAN) (EE, RUS)
4-129-234-11 (ARABIC) (E)
4-129-234-21 (PERSIAN) (E)
4-129-234-31 (SIMPLIFIED CHINESE) (HK)
4-129-234-41 (TRADITIONAL CHINESE) (HK, TW)
Conversion (2P) Adaptor
0
1-569-008-12
(E (Central and South America))
The components identified by
mark
mark
0 or dotted line with
mark
0 are critical for safety.
Replace only with part number
specified.
specified.
Les composants identifiés par une
marque
marque
0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Ver. 1.3 2010.03
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Display