Sony MHS-TS55 (serv.man2) Service Manual ▷ View online
MHS-TS55_ADJ
5-5
5-3-4. WB/AGC Adjustment
The WB/AGC (White Balance/Analog Gain Control) adjustment order
is as follows.
is as follows.
Note:
Perform this adjustment after that performed in 5-3-3.
Perform this adjustment after that performed in 5-3-3.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
Fig.
5-3-10
The adjustment is complete.
The adjustment is finished abnormally.
Fig.
5-3-11
Malfunction of WB/AGC
adjustment result
adjustment result
Finished normally.
Finished abnormally.
Confirm the indication
on the screen.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Touch the Left area, Right area, or the Top area, Bottom area on the LCD screen to choose an adjustment item.
Select “WB/AGC (LV10)”, press the
Select “WB/AGC (LV10)”, press the
(Shutter) button
, then confirm that each value of “Light Src” is set as “002”,
“P1 R Ratio” is set as “1038”, and “P1 B Ratio” is set as “916”.
“P2 R Ratio” is set as “1332”, and “P2 B Ratio” is set as “703”.
“P2 R Ratio” is set as “1332”, and “P2 B Ratio” is set as “703”.
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-9)
Touch the Left area, Right area, or the Top area, Bottom area on the LCD screen to choose an adjustment item
.
Select
“WB/AGC (LV10)”, and touch the Center area on the LCD screen.
Select “OK”, and touch the Center area of the LCD screen to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-11)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-3-11)
In this case, confirm the adjusting environment
and readjust.
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-10)
Press the
the adjustment completion indication appears
on the screen. (Fig. 5-3-10)
Press the
(Shutter) button
to return to
adjustment menu.
The adjustment is finished normally.
Fig.
5-3-7
The adjustment is complete.
5-3-3. OB Adjustment
The OB (Optically Black) adjustment order is as follows.
The adjustment is finished abnormally.
Fig.
5-3-8
Malfunction of OB
adjustment result
adjustment result
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Cover camera lens (All black). (Fig. 5-3-6)
Touch the Left area, Right area, or the Top area, Bottom area on the LCD screen to choose an adjustment item.
Select “OB CLBT (BLACK)”, and touch the Center area on the LCD screen.
Select “OK”, and touch the Center area of the LCD screen to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
Select “OB CLBT (BLACK)”, and touch the Center area on the LCD screen.
Select “OK”, and touch the Center area of the LCD screen to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-7)
Press the
the adjustment completion indication appears
on the screen. (Fig. 5-3-7)
Press the
(Shutter) button to return to
adjustment menu.
Finished normally.
Finished abnormally.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-8)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-3-8)
In this case, confirm the adjusting environment
and readjust.
Confirm the indication
on the screen.
Adjustment order
Screen display
Adjustment order
Screen display
Equipments required: Cover camera lens
(All black)
Camera
Black cloth
Fig.
5-3-6
Small pattern box
(PTB-1450)
(PTB-1450)
5 mm or less
Black cloth
Camera
Equipments required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
Small pattern box (PTB-1450)
(All black)
Clear chart
Fig.
5-3-9
MHS-TS55_ADJ
5-6
5-3-5. Dark DP Adjustment
The Dark DP (Dead Pixel) adjustment order is as follows.
Note:
Perform this adjustment after those performed in 5-3-3 to 5-3-4.
Perform this adjustment after those performed in 5-3-3 to 5-3-4.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
Fig.
5-3-13
The adjustment is complete.
The adjustment is finished abnormally.
Fig.
5-3-14
Malfunction of Dark DP
adjustment result
adjustment result
5-3-6. Light/S.S Adjustment
The Light/S.S (Light Dead Pixel/Slow Shutter Dead Pixel)
adjustment order is as follows.
adjustment order is as follows.
Note 1:
Perform this adjustment after those performed in 5-3-3 to 5-3-5.
Note 2:
Select [MENU] - [Main Settings] - [LUN Settings (USB)] and confirm that [Multi]
is selected. If [Single] is selected, the adjustment does not succeed.
Perform this adjustment after those performed in 5-3-3 to 5-3-5.
Note 2:
Select [MENU] - [Main Settings] - [LUN Settings (USB)] and confirm that [Multi]
is selected. If [Single] is selected, the adjustment does not succeed.
The adjustment is finished normally.
Fig.
5-3-16
The adjustment is complete.
The adjustment is finished abnormally.
Fig.
5-3-17
Malfunction of Light/S.S
adjustment result
adjustment result
* F
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-14)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-3-14)
In this case, confirm the adjusting environment
and readjust.
Touch the Left area, Right area, or the Top area, Bottom area on the LCD screen to choose an adjustment item.
Select “ Dark DPC (LV10)”, and touch the Center area on the LCD screen.
Select “OK”, and touch the Center area of the LCD screen to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
Select “ Dark DPC (LV10)”, and touch the Center area on the LCD screen.
Select “OK”, and touch the Center area of the LCD screen to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-13)
Press the
the adjustment completion indication appears
on the screen. (Fig. 5-3-13)
Press the
(Shutter) button
to return to
adjustment menu.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-12)
Restart the camera.
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-17)
In this case, confirm the adjusting environment
and make adjustment again from "5-3-5. Dark
DP Adjustment."
the following indication appears on the screen.
(Fig. 5-3-17)
In this case, confirm the adjusting environment
and make adjustment again from "5-3-5. Dark
DP Adjustment."
Touch the Left area, Right area, or the Top area, Bottom area on the LCD screen to choose an adjustment item.
Select “Light S.S (BLACK)”, and touch the Center area on the LCD screen.
Select “OK”, and touch the Center area of the LCD screen to start.
*1 If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
*2 It may take more than 3 hours on this adjustment depending on the environments and the battery conditions.
Select “Light S.S (BLACK)”, and touch the Center area on the LCD screen.
Select “OK”, and touch the Center area of the LCD screen to start.
*1 If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
*2 It may take more than 3 hours on this adjustment depending on the environments and the battery conditions.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Confirm that the unit has entered the Adjustment mode, and tthen connect the USB charging adaptor.
Cover camera lens (All black) (Fig. 5-3-15)
Restart the camera.
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-16)
Press the
the adjustment completion indication appears
on the screen. (Fig. 5-3-16)
Press the
(Shutter) button
to return to
adjustment menu.
Adjustment order
Screen display
Adjustment order
Screen display
Small pattern box
(PTB-1450)
(PTB-1450)
5 mm or less
Black cloth
Camera
Equipments required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
Small pattern box (PTB-1450)
(All black)
Clear chart
Fig.
5-3-12
Equipments required: Cover camera lens
(All black)
Camera
Black cloth
Fig.
5-3-15
MHS-TS55_ADJ
5-7
The adjustment is finished abnormally.
Fig.
5-3-20
Malfunction of Lens
shading adjustment result
shading adjustment result
5-3-7. Lens Shading Adjustment
The Lens shading adjustment order is as follows.
Note:
Perform this adjustment after those performed in 5-3-3 to 5-3-6.
Perform this adjustment after those performed in 5-3-3 to 5-3-6.
Small pattern box (PTB-1450) setting:
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
Color temperature = 3100 ± 200K
Luminance: LV12.2 ± 0.5
The adjustment is finished normally.
Fig.
5-3-19
The adjustment is complete.
Confirm the indication
on the screen.
Finished abnormally.
Finished normally.
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
(Fig. 5-3-20)
In this case, confirm the adjusting environment
and readjust.
the following indication appears on the screen.
(Fig. 5-3-20)
In this case, confirm the adjusting environment
and readjust.
Touch the Left area, Right area, or the Top area, Bottom area on the LCD screen to choose an adjustment item.
Select “
Select “
Lens Shad (LV10)”, and touch the Center area on the LCD screen.
Select “OK”, and touch the Center area of the LCD screen to start.
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
* If the adjustment is disabled, refer to “5-1-6. Enabling the Adjustment” to enable the adjustment. (Page 5-3)
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-3-19)
Press the
the adjustment completion indication appears
on the screen. (Fig. 5-3-19)
Press the
(Shutter) button
to return to
adjustment menu.
Check that the camera is on the adjustment mode.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-3-18)
Touch the Left area, Right area, or the Top area, Bottom area on the LCD screen to choose an adjustment item.
Select
Select
“Lens Shad (LV10)”, press the
(Shutter) button, then confirm that the value of “Lsd/Flash” is set as “002”.
Adjustment order
Screen display
5-3-8. Set Language Destination
Note:
Finish all of the adjustment except for the Language destination setting.
Once the Language destination setting is finished, it cannot be reset.
Once the Language destination setting is finished, it cannot be reset.
USB Driver and Service Tool
Put the two folders “USB Driver” and “Service Tool” downloaded in “5-1-5. Setting the Adjustment Mode” (Page 5-3) in any place of the PC.
Put the two folders “USB Driver” and “Service Tool” downloaded in “5-1-5. Setting the Adjustment Mode” (Page 5-3) in any place of the PC.
The procedure of installing a USB driver is as follows.
1) Execute the “DirectUSB-Setup.exe” in the “USB Driver” folder to start up the Installer.
2) Install the USB driver according to the guidance on the screen.
3) Connect the camera started up with the adjustment mode, and the PC with a USB extension cable.
4) Adapt the USB driver installed in step 2) according to the guidance on the screen.
1) Execute the “DirectUSB-Setup.exe” in the “USB Driver” folder to start up the Installer.
2) Install the USB driver according to the guidance on the screen.
3) Connect the camera started up with the adjustment mode, and the PC with a USB extension cable.
4) Adapt the USB driver installed in step 2) according to the guidance on the screen.
Connecting USB to PC
Connect the equipments as shown below. (Fig. 5-3-21)
Connect the equipments as shown below. (Fig. 5-3-21)
USB extension cable
Insert all the way
(A plug to A socket)
(Commercially available)
(Commercially available)
Fig.
5-3-21
Starting up the Service Tool
Execute the “ServiceTool_Ver[][][].exe” in the “Service Tool” folder to start up the Service Tool. (Fig. 5-3-22)
Fig.
5-3-22
Small pattern box
(PTB-1450)
(PTB-1450)
5 mm or less
Black cloth
Camera
Equipments required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
Small pattern box (PTB-1450)
(All black)
Clear chart
Fig.
5-3-18
MHS-TS55_ADJ
5-8E
DESTINA
TION
AREA
SELECTABLE LANGUAGE
HDMI Output
Default
Japanese
English
French
German
Spanish
Italian
Portuguese
Simplified Chinese
T
raditional Chinese
Arabic
Dutch
Russian
Swedish
Korean
Norwegian
Danish
Finnish
Polish
Hungarian
Czech
Persian
Thai
Greek
T
urkish
Malay
Croatian
Romanian
Indonesian
Bulgarian
V
ietnamese
U
US
z
60i (60Hz)
z
: INITIAL LANGUAGE
The setting is finished normally.
Fig.
5-3-23
The setting is complete.
The setting is finished abnormally.
Fig.
5-3-24
Malfunction of Set
Language destination result
Language destination result
Example:
Connect USB NG!!
Connect USB NG!!
Fig.
5-3-25
Malfunction of Set
Language destination result
Language destination result
Example:
SERIAL No Length ERROR!!
SERIAL No Length ERROR!!
The Language destination setting order is as follows.
Setting order
Confirm the indication
on the screen.
Press the “Read” button, “PRODUCT CODE” and “SERIAL No.” will displayed on the screen.
Select the correspond language destination from the pull-down menu, input the “SERIAL No.”, then press the “Write” button.
*1 The “SERIAL No.” is written on the side of the camera.
Select the correspond language destination from the pull-down menu, input the “SERIAL No.”, then press the “Write” button.
*1 The “SERIAL No.” is written on the side of the camera.
*2 Once the Language destination setting is finished, it cannot be reset.
Disconnect the USB connection, turn on
the power of the camera, and then perform
the initial setting.
the power of the camera, and then perform
the initial setting.
In case of the setting is finished normally,
the setting completion indication appears on
the screen. (Fig. 5-3-23)
The power of the camera turns off automatically.
the setting completion indication appears on
the screen. (Fig. 5-3-23)
The power of the camera turns off automatically.
In case of the setting is finished abnormally,
the following message appears on the screen.
(Fig. 5-3-24, 5-3-25)
In this case, perform the setting again upon
the message.
the following message appears on the screen.
(Fig. 5-3-24, 5-3-25)
In this case, perform the setting again upon
the message.
Finished abnormally.
Finished normally.
Screen display
Selectable language table
Display
