Sony MHS-FS1 / MHS-FS1K / MHS-FS2 / MHS-FS2K (serv.man3) Service Manual ▷ View online
MHS-FS1/FS1K/FS2/FS2K_ADJ
5-5
5-2-2. AWB Adjustment
(1) AWB Adjustment
The White Balance and Bad Pixel Adjustment is as follows.
Small pattern box (PTB-1450) setting:
Color temperature = 3150 ± 50K
Luminance: LV12.3 ± 0.2
The adjustment finished normally.
Fig. 5-2-8
Bad Pixel Ok OOO
WB OK OOO
WB OK OOO
When the adjustment is finished
normally, perform the “Lens
Shading Adjustment”.
The adjustment is finished abnormally.
Cal LWB 1
WB NG XXX
R:xxx G:xxx B:xxx
Referrence:
R:xxx G:xxx B:xxx
Fig. 5-2-9
Malfunction of White Balance
adjustment
WB OK OOO
Bad Pixel NG XXX
Fig. 5-2-10
Malfunction of Bad Pixel adjust-
ment
Adjustment order
Screen display
Fig. 5-2-7
Equipment required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
(All black)
Small pattern box
(PTB-1450)
3mm or less
Black cloth
Camera
Check that the camera is on the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
∗ For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450) and cover them (all black) with black cloth. (Fig. 5-2-7)
Press the Multi-selector button “ b (Key Left)”.
the adjustment completion indication appears
on the screen. (Fig. 5-2-8)The adjustment will
proceed to “Lens Shadig Adjustment”,
do not execute the
button (Key S1) operation.
In case of the adjustment is finished normally,
the following indication appears on the screen.
(Fig. 5-2-9 and 5-2-10)
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
and readjust.
Press the
button (Key S1), then AWB Adjustment starts.
(2) Lens shading Adjustment
When the indication (Fig. 5-2-11) appears on the LCD display, set the
adjustment jig according to procedures shown below. (Fig. 5-2-12)
1) Attach the Light balance filter to the tip of the camera lens.
2) place the camera in front of the small pattern box
The adjustment finished normally.
Fig. 5-2-13
Lens shading OK OOO
The adjustment is complete.
The adjustment is finished abnormally.
Lens shading NG XXX
Fig. 5-2-14
Malfunction of Lens shading
adjustment
Adjustment order
Screen display
Fig. 5-2-12
Equipment required: Small pattern box (PTB-1450)
Cover camera lens and
Small pattern box (PTB-1450)
(All black)
Light balance filter
Light balance filter
Small pattern box
(PTB-1450)
3mm or less
Black cloth
Camera
Small pattern box (PTB-1450) setting:
Color temperature = 5200 ± 300K
Luminance: LV12.75 ± 0.2
Fig. 5-2-11
Lens Shading ADJ...
V3.01ADJ
2011-03-30
Please Key S1 Start...
Attach the Light balance filter to the tip of the camera lens.
Check that the AWB Adjustment is finished normally.
Place the camera in front of the Small pattern box (PTB-1450) and cover them (all black) with black cloth. (Fig. 5-2-12)
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
the adjustment completion indication appears
on the screen. (Fig. 5-2-13)
Turn off the power to quit the adjustment mode.
In case of the adjustment is finished normally,
the following indication appears on the screen.
(Fig. 5-2-14)
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
and readjust.
Press the
button (Key S1), then Lens Shading Adjustment starts.
The changed portions from
Ver.1.0 are shown in blue.
Ver.1.1 2011.04
MHS-FS1/FS1K/FS2/FS2K_ADJ
5-6
5-2-3. Bright Pixel Adjustment
The Bright Pixel Adjustment is as follows.
Note:
• Perform this adjustment after that performed in 5-2-2. AWB Adjustment.
• It takes more than 40 minutes to perform the Bright Pixel Adjustment
(including more than 10 minutes for warming-up, and more than 30 minutes
for main adjustment).
The adjustment finished normally.
Fig. 5-2-20
Burnin
OK
OK Burnin defect pixel
The adjustment is complete.
The adjustment is finished abnormally.
Still Adjusting ...
BadCount: xxxxx
Bright Pixel NG XXX
over
Fig. 5-2-21
Malfunction of Bright Pixel
adjustment
NG Burnin dfect Pixel
Fig. 5-2-22
Malfunction of Burnin dfect
Pixel adjustment
Adjustment order
Screen display
Fig. 5-2-16
Run: 0001 TimeCnt: 0120
Connect the USB charging adaptor.
Fig. 5-2-18
Still Adjusting...
BadCount: xxxxx
Bright Thd: XXXX
Over
Still Adjusting...
BadCount: xxxxx
Bright Thd: XXXX
Below
The automatic adjustment is complete.
Fig. 5-2-19
Run: 0020 TimeCnt: 0360
The warming up is complete.
Fig. 5-2-17
Still Adjusting...
The adjustment starts automatically.
Fig. 5-2-15
Equipments required: Cover camera lens
(All black)
Camera
Black cloth
Check that the camera is on the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
∗ For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Cover camera lens (all black). (
Fig. 5-2-15
)
Press the Multi-selector button “ V (Key Down)”.
the adjustment completion indication appears
on the screen. (
Fig. 5-2-20
)
The adjustments required when replacing Lens
Block for MHS-FS1/FS2 are completed.
Remove the adjustment FW according to
procedures shown below.
1) Turn off the power of the camera.
2) Disconnect the USB cable from the USB charge adaptor.
3) Connect the USB cable disconnected in step 2) to PC.
4) Turn on the power of the camera.
5) Remove the SDV5092C.bin saved in the
“BLOGGIE_SW” root directory.
In case of the adjustment is finished normally,
the following indication appears on the screen.
(
Fig. 5-2-21 and 5-2-22
)
In case of the adjustment is finished abnormally,
In case of the Bright Pixel adjustment is failed,
after turning off the power of the camera,
restart the adjustment from the AWB adjustment.
Press the
button (Key S1), then Bright Pixel Adjustment starts.
Connect the USB charging adaptor after the screen turned to that shown in
Fig. 5-2-16
.
The camera will automatically keep operating abnormally for more than 10 minutes during warming up.
Perform the adjustment from beginning if the screen got frozen.
The screen will light out for a few seconds, then turn to that shown in
Fig. 5-2-17
and start the adjustment automatically.
After the automatic adjustment finished, the screen will turn to that shown in
Fig. 5-2-18
.
In case of over, warming up will restart automatically.
In case of below, it will proceed to the next step automatically.
The camera will automatically keep operating abnormally for more than 30 minutes
after the screen turned to that shown in
Fig. 5-2-19
.
Perform the adjustment from beginning if the screen got frozen.
The changed portions from
Ver.1.0 are shown in blue.
Ver.1.1 2011.04
MHS-FS1/FS1K/FS2/FS2K_ADJ
5-7
5-2-5. Set Language Destination
Language Destination Setting:
Save “lang.txt” in the root directory of the slot named ”BLOGGIE”.
The content of “lang.txt” is as follows:
Language Destination (for example: 5_UC3) (enter key)
Product ID (10bit) (enter key) (refer to “5-3 PRODUCT ID LIST”)
S/N (8bit) (enter key)
The following is an example of 5_UC3 Language Destination Setting for MHS-FS1 White camera.
5_UC3
0002095930
08432345
Especially Attention:
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST”, and the Product ID must be 10bit.
If the Product ID is less than 10 bit, add 0 before the Product ID.
3) The S/N must be 8 bit. It refer to the serial number of shipment.
The adjustment is finished abnormally.
Set LangDest NG!
Pls check Lang.txt
or if MassProduct!
SETTING XXX
Fig. 5-2-28
Malfunction of Set Language
Destination
In case of the Set Language
Destination is failed, reset the
language destination.
Adjustment order
Screen display
The adjustment finished normally.
The adjustment finished normally.
Set LangDest OK!
Dest: 5_UC3
ProductNum:
0002095930
S/N:
08432345
Color: white
Fig. 5-2-27
The adjustment is complete.
Note: The screen shown above is an example.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
Set the camera to the adjustment mode.
∗ For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Press the
button (Key S1), then Language Destination Setting starts.
Press the MOVIE/ENTER button (Key OK).
the adjustment completion indication appears
on the screen in a moment. (
Fig. 5-2-27
)
The adjustment will proceed to “Check all above
adjustment result”, do not execute any key operation.
In case of the adjustment is finished normally,
the following indication appears on the screen.
(
Fig. 5-2-28
)
and readjust.
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
5-2-4. M360 Adjustment (MHS-FS1K/FS2K Only)
The M360 Adjustment is as follows.
Press and hold both sides of the 360 video lens (1), then attach it to the camera in the
direction (2).
Note 1: Attach the hooks of the 360 video lens to the attaching parts of the camera, as shown in
Fig. 5-2-23
.
Note 2: When repairing the parts related to the lens module of FS1K or FS2K.
• Ask the customer to send the 360 Video Lens with the unit.
• Perform M360 Adjustment with the 360 Video Lens sent from the customer.
The adjustment finished normally.
Save callb value OK
Fig. 5-2-25
Save status OK
Ct X:xxxx Yxxx offset Xxx Yx
Ct X:xxxx Yxxx offset Xxx Yx
The adjustment is complete.
The adjustment is finished abnormally.
out of the range
Fig. 5-2-26
Malfunction of 360 adjustment.
If the white pane departs from
the 360 video lens too much,
which cause it is beyond the
compensation scope of FW.
Press “S1” button to readjust
360.
Adjustment order
Screen display
Fig. 5-2-23
Equipments required: 360 video lens
360 video lens
1
2
1
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Mount the 360 video lens to the camera. (
Fig. 5-2-23
)
Press the MOVIE/ENTER button (Key OK).
In case of the adjustment is finished normally, the
adjustment completion indication appears on the screen.
(
Fig. 5-2-25
)
The adjustments required when replacing Lens Block for
MHS-FS1K/FS2K are completed.
Remove the adjustment FW according to procedures
shown below.
1) Turn off the power of the camera.
2) Disconnect the USB cable from the USB charge adaptor.
3) Connect the USB cable disconnected in step 2) to PC.
4) Turn on the power of the camera.
5) Remove the SDV5092C.bin saved in the
“BLOGGIE_SW” root directory.
the following indication appears on the screen.
(
Fig. 5-2-26
)
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
and readjust.
Press the Multi-selector button “ B (Key Right)”, then press the
button (Key S1).
Move the white pane to match it with the center of the ring-shaped image
by pressing the Multi-selector buttons “v (Key Up)”, “V (Key Down)”,
“b (Key Left)” and “B (Key Right)”.
White pane
Ring-shaped image
Fig. 5-2-24
The changed portions from
Ver.1.0 are shown in blue.
Ver.1.1 2011.04
MHS-FS1/FS1K/FS2/FS2K_ADJ
5-8
Selectable language table
5-3. PRODUCT ID LIST
MHS-FS1
Destination
Color
Product ID
5_CE7
White
0002095956
Black
0002096756
5_ET4
White
0002095970
Black
0002096770
5_UC3
White
0002095930
Black
0002096730
6_UC3
White*
0002095939
Black*
0002096739
MHS-FS2
Destination
Color
Product ID
5_CE7
White
0002094656
Violet
0002095256
5_ET4
White
0002094670
Green
0002094970
Pink
0002095070
Violet
0002095270
5_UC3
White
0002094630
Green
0002094930
Pink
0002095030
Violet
0002095230
6_UC3
White*
0002094639
Green*
0002094939
Pink*
0002095039
Violet*
0002095239
MHS-FS2K
Destination
Color
Product ID
5_ET4
White
0002096870
Green
0002096970
Pink
0002097170
Violet
0002097370
5_UC3
White
0002096830
Green
0002096930
Pink
0002097130
Violet
0002097330
6_UC3
White*
0002096839
Green*
0002096939
Pink*
0002097139
Violet*
0002097339
* Walmart model
DESTINA
TION
AREA
SELECTABLE LANGUAGE
English
French
German
Spanish
Italian
Portuguese
Simplified Chinese
Traditional Chinese
Arabic
Dutch
Russian
Swedish
Korean
Norwegian
Danish
Finnish
Polish
Hungarian
Czech
Persian
Thai
Greek
Turkish
Malay
Croatian
Romanian
Indonesian
Bulgarian
Vietnamese
UC3
US
z
a
a
a
CND
z
a
a
a
CE7
AEP
z
a
a
a
a
a
a
a
a
a
a
a
a
a
ET4
E
z
a
a
a
a
a
a
a
a
a
a
a
z
: INITIAL LANGUAGE
MHS-FS1K
Destination
Color
Product ID
5_CE7
Black
0002097756
5_ET4
White
0002097670
Black
0002097770
5_UC3
White
0002097630
Black
0002097730
6_UC3
White*
0002097639
Black*
0002097739
5-2-6. Check all above adjustment result (When Replacing Main Board only)
After doing set language adjustment, it will check all above adjustment result automatically.
There is less than one adjustment is NG.
(Take one for example (
Fig.5-2-30 to Fig.5-2-35
).)
X AF Adjust : NG
O AWB Adjust : OK
O BrightDefectPix : OK
O DarkDefectPix : OK
O M360 Adjust : OK
O SetLang Adjust : OK
Fig. 5-2-30
O AF Adjust : NG
X AWB Adjust : OK
O BrightDefectPix : OK
O DarkDefectPix : OK
O M360 Adjust : OK
O SetLang Adjust : OK
Fig. 5-2-31
O AF Adjust : NG
O AWB Adjust : OK
X BrightDefectPix : OK
O DarkDefectPix : OK
O M360 Adjust : OK
O SetLang Adjust : OK
Fig. 5-2-32
O AF Adjust : NG
O AWB Adjust : OK
O BrightDefectPix : OK
X DarkDefectPix : OK
O M360 Adjust : OK
O SetLang Adjust : OK
Fig. 5-2-33
O AF Adjust : NG
O AWB Adjust : OK
O BrightDefectPix : OK
O DarkDefectPix : OK
X M360 Adjust : OK
O SetLang Adjust : OK
Fig. 5-2-34
O AF Adjust : NG
O AWB Adjust : OK
O BrightDefectPix : OK
O DarkDefectPix : OK
O M360 Adjust : OK
X SetLang Adjust : OK
Fig. 5-2-35
Screen display
All above adjustment is OK.
All above adjustment is OK.
O AF Adjust : OK
O AWB Adjust : OK
O BrightDefectPix : OK
O DarkDefectPix : OK
O M360 Adjust : OK
O SetLang Adjust : OK
Fig. 5-2-29
5-2-7. Remove adjustment FW (When Replacing Main Board only)
After checking all above adjustment result (When Replacing Main Board only), it will remove adjustment FW automatically.
XXX NG
Error:Adjust FW
can not removed
Error:Adjust FW
can not removed
Fig. 5-2-37
Failed in removing adjustment FW.
If the adjustment FW cannot be
removed automatically, perform
the following procedures to
remove it.
1)
Turn off the power of the
camera.
2)
Disconnect the USB cable
from the USB charge adaptor.
3)
Connect the USB cable
disconnected in step 2) to PC.
4)
Turn on the power of the
camera.
5)
Remove the SDV5092C.bin
saved in the “BLOGGIE_SW”
root directory.
Screen display
OOO OK
Adjust FW
have removed
Adjust FW
have removed
Fig. 5-2-36
Succeeded in removing adjust-
ment FW.
The changed portions from
Ver.1.0 are shown in blue.
Ver.1.1 2011.04
Display
