Sony HDR-UX1 (serv.man2) Service Manual ▷ View online
— 5 —
HDR-UX1/UX1E_ADJ
&
: Points added portion.
2.
Adjustment Items of Camera System Adjustment
(Service manual page 6-16)
The adjustment items of camera system adjustment are as listed in
Table 6-1-3. The Automatic Adjustment Program divides the ad-
justment items into seven, camera adjustment 1-7. Clicking either
CAMERA Adjustment Start button allows the adjustment item
which corresponds to that button to be executed.
The adjustment items of camera system adjustment are as listed in
Table 6-1-3. The Automatic Adjustment Program divides the ad-
justment items into seven, camera adjustment 1-7. Clicking either
CAMERA Adjustment Start button allows the adjustment item
which corresponds to that button to be executed.
Table 6-1-3
The adjustment conditions of the subject and filter vary depend-
ing on which item is adjusted. The Adjustment Program displays
an instruction for the subject and filter as a message during the
adjustment.
ing on which item is adjusted. The Adjustment Program displays
an instruction for the subject and filter as a message during the
adjustment.
Block
Page
Address
Initialization of
EEPROM Data
EEPROM Data
Initialization of EEPROM data
Not required
11
80
0F00 to 0FFF,
6300 to 6FFF
6300 to 6FFF
HALL Adj.
11
80
69D0 to 69D8
MR Adj.
11
80
6F30,
6F40 to 6F4B
6F40 to 6F4B
Differential Gain Adj.
Clear chart (All White)
(Shoot the clear chart with the zoom
TELE end.)
(Shoot the clear chart with the zoom
TELE end.)
11
80
6E00 to 6EB3
CAMERA
Adjustment 1
Adjustment 1
Not required
Adjusting Address
Button Name
Adjustment
Subject
*
Initialization of EEPROM Data
The EEPROM data of the board for service has already been
initialized, not requiring further initialization when the board is
replaced.
Execute this processing only when the EEPROM is replaced.
If the EEPROM data is initialized, all the camera adjustment
data is also initialized. All items of the camera adjustments must
be performed after the initialization of EEPROM data.
initialized, not requiring further initialization when the board is
replaced.
Execute this processing only when the EEPROM is replaced.
If the EEPROM data is initialized, all the camera adjustment
data is also initialized. All items of the camera adjustments must
be performed after the initialization of EEPROM data.
[Initializing method]
1) Click the [Initialization of EEPROM Data] button on Cam-
1) Click the [Initialization of EEPROM Data] button on Cam-
era Adjustment screen, and the following screen will ap-
pear.
pear.
2) Select the model name with the Model Name List.
3) Click the [Data Write] button.
4) The writing finishes when the following message is displayed.
“Initialization of EEPROM Data” is added to front
of “3. CAMERA Adjustment 1”.
of “3. CAMERA Adjustment 1”.
(Service manual page 6-17)
+
— 6 —
HDR-UX1/UX1E_ADJ
• Addition of Note for Record Data
&
: Points added portion.
6-3. SERVICE MODE
3-2.
SERVICE MODE
6.
Record Data
(Service manual page 6-53)
Click the [Record Data] button on the SERVICE MODE screen,
and the “RECORD DATA” screen will appear.
Click the [Record Data] button on the SERVICE MODE screen,
and the “RECORD DATA” screen will appear.
The record data such as use record and self-diagnostic record are
displayed.
displayed.
Initializing method (Self-Diagnosis Data Only):
Click the [Clear Self-Diagnosis Data Only] button on the screen, and
the Self-Diagnosis Data will be initialized.
Click the [Clear Self-Diagnosis Data Only] button on the screen, and
the Self-Diagnosis Data will be initialized.
Note: If a flash error (self-diagnosis code E:91:**) occurred, all
recorded data must be initialized to reset the error. The
error cannot be reset by initializing the self-diagnosis data
only.
error cannot be reset by initializing the self-diagnosis data
only.
Initializing method (All Record-Data):
Click the [Clear All Recorded-Data] button on the screen, and the
All Recorded-Data will be initialized.
Note: Performing the initialization causes all the user settings in-
Click the [Clear All Recorded-Data] button on the screen, and the
All Recorded-Data will be initialized.
Note: Performing the initialization causes all the user settings in-
cluding time setting to be initialized, too.
(
— 7 —
HDR-UX1/UX1E_ADJ
(JAPANESE: Pages 7 to 11)
・「EEPROMデータの初期化」の追加
&
：追加箇所
・調整の前に
1-1. 主要部品および基板交換時の要調整項目
・主要部品交換時の調整項目
・主要部品交換時の調整項目
（Supplement-1 6-1ページ）
主要部品交換時には，下表の●で示された項目を調整してください。
注1：自動調整プログラムは，対応していません。
表6-1-1 (1)
レンズデバイス
ドライブブロック
LCDブロック LCD9001 （LCDパネル）
LCDブロック D9001 （LCDバックライト）
EVFブロック LCD9002 （LCDパネル）
FL20000ブロック フラッシュユニット
MICユニット MIC9001
CM-074 board IC6001 (CMOS imager)
CM-074 board SE6801, 6802 (PITCH, YAW sensor)
VC-456 board IC1201 (CDS, A/D conv.)
VC-456 board IC1301, X1301 (Clock generator)
VC-456 board IC2401 (Down conv.)
VC-456 board IC2601 (Component out AMP)
VC-456 board IC2901 (Video, Audio I/O)
VC-456 board IC3001 (MIC AMP)
VC-456 board IC3101 (Sub MIC AMP)
VC-456 board IC3303 (EVF drive)
BL-003 board D5401 (EVF backlight)
MD-131 board IC4101 (RF process)
MD-131 board IC4201 (DVD DSP)
MD-131 board IC4401 (DVD mecha drive)
PD-291 board IC5701 (LCD drive)
仕向けデータ
書き込み
仕向けデータ書き込み
（注 1）
原発振確認
Sビデオ出力Yレベル調整
Sビデオ出力クロマレベル調整
ビデオ出力レベル確認
コンポーネント出力Yレベル調整
コンポーネント出力Pbレベル調整
コン ポ ーネント出力Prレベル調整
Sビデオ出力Yレベル調整
Sビデオ出力クロマレベル調整
ビデオ出力レベル確認
コンポーネント出力Yレベル調整
コンポーネント出力Pbレベル調整
コン ポ ーネント出力Prレベル調整
EEPROM
データの初期化
EEPROMデータの初期化
ホール調整
MR調整
Differential gain調整
MR調整
Differential gain調整
z
z
z
z
調整
ブロック交換
交換部品
調整項目
カメラ調整 1
ビデオ調整
z
部品交換
z
z
*
— 8 —
HDR-UX1/UX1E_ADJ
&
：追加箇所
・基板およびEEPROM交換時の要調整項目
（Supplement-1 6-2ページ）
基板およびEEPROM交換時には，下表の●で示された項目を調整してください。
注2： 修理完了時，必ず，下記の確認を
行ってください。
1. 全黒の被写体を撮像し，画面中心に縦
線が見えないこと，また，左右の輝度
レベルに差が無いこと。
2. 低照度の被写体を撮像し，画面中心に
縦線が見えないこと，また，左右の輝
度レベルに差が無いこと。
3. 通常照度の被写体を撮像し，画面中心
に縦線が見えないこと，また，左右の
輝度レベルに差が無いこと。もし，異
常のある場合は「Differential Gain調整」
の全工程を行ってください。
注3： VC-456基板のIC1601（HI/DSコント
ロール，フラッシュメモリ）とMD-
131基板のIC4302（フラッシュメモ
リ）は交換不可です。
CM-074 board (COMPLETE)
VC-456 board (COMPLETE)
BL-003 board (COMPLETE)
MD-131 board (COMPLETE)
PD-291 board (COMPLETE)
VC-456 board IC1402 (EEPROM)
仕向けデータ
書き込み
仕向けデータ書き込み
（注 1）
原発振確認
z
Sビデオ出力Yレベル調整
Sビデオ出力クロマレベル調整
ビデオ出力レベル確認
コンポーネント出力Yレベル調整
コンポーネント出力Pbレベル調整
コン ポ ーネント出力Prレベル調整
Sビデオ出力クロマレベル調整
ビデオ出力レベル確認
コンポーネント出力Yレベル調整
コンポーネント出力Pbレベル調整
コン ポ ーネント出力Prレベル調整
EEPROM
データの初期化
EEPROMデータの初期化
z
ホール調整
MR調整
Differential gain調整
MR調整
Differential gain調整
z
EEPROM
交換
カメラ調整 1
z
z
調整項目
調整
ビデオ調整
基板交換
z
z
*
表6-1-1 (2)
Click on the first or last page to see other HDR-UX1 (serv.man2) service manuals if exist.