Sony HDR-UX1 / HDR-UX1E (serv.man4) Service Manual ▷ View online
6-34
HDR-UX1/UX1E_ADJ
6-2. DRIVE SECTION ADJUSTMENTS
2-1.
PREPARATIONS BEFORE ADJUSTMENTS (DRIVE SECTION)
2-1-1.
Connection
1) Connect the apparatuses as shown below, and perform adjustment.
Note 1: Before starting the adjustment, remove the disc from the camcorder.
Note 1: Before starting the adjustment, remove the disc from the camcorder.
Fig. 6-2-1
Note 2: Refer to “How to Set the Optical Sensor Disc”.
PC
(The SeusEX must be installed in the PC.)
OS: Windows 2000/XP
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
Three connectors are required.
RAM: 256MB or more recommended
USB: 2.0 recommended (also compatible with 1.1)
Three connectors are required.
HASP Key
USB cable
(1-829-759-41)
(1-829-759-41)
To USB jack
POWER Adjustment
Optical power meter
(J-6082-569-A)
(J-6082-569-A)
Optical sensor disc
(J-6082-570-A)
(J-6082-570-A)
To DRIVE (Note 2)
To DC IN jack
AC IN
AC adaptor
AC-L15A
(1-479-283-34)
AC-L15A
(1-479-283-34)
[Connecting method]
1) Connect the Camcorder to the PC with a USB cable, and turn
1) Connect the Camcorder to the PC with a USB cable, and turn
on the power switch.
2) The USB SELECT menu will appear on the LCD screen of the
Camcorder, and then select “COMPUTER (Memory Stick) ” to
establish the connection.
establish the connection.
Note 3: Don’t select “COMPUTER (Disc) ”.
6-35
HDR-UX1/UX1E_ADJ
2-1-3.
Precautions on Adjustment
1.
Adjustment data
The adjustment data for the drive block are recorded to the IC4302
on the MD-131 board.
These data cannot be read or written from the adjustment remote
commander or SeusCam, unlike the camera and LCD adjustment
data.
Accordingly, be sure to adjust all items of the drive adjustment
when the following parts were replaced:
• Drive block
on the MD-131 board.
These data cannot be read or written from the adjustment remote
commander or SeusCam, unlike the camera and LCD adjustment
data.
Accordingly, be sure to adjust all items of the drive adjustment
when the following parts were replaced:
• Drive block
• Mounted MD-131 board
• IC4101 (RF process) on the MD-131 board
• IC4201 (DVD DSP) on the MD-131 board
• IC4401 (DVD mecha drive) on the MD-131 board
2.
Order of adjustment
Adjust the drive block in the following order:
1) POWER Adjustment
2) SERVO Adjustment
1) POWER Adjustment
2) SERVO Adjustment
3.
Precaution on the laser diode
In the POWER Adjustment, operate the drive with the disc cover
left open. During the adjustment, be sure to observe the fol-
lowing precautions:
1) Set the optical sensor disc correctly.
2) Keep the distance of more than 30 cm apart from the
left open. During the adjustment, be sure to observe the fol-
lowing precautions:
1) Set the optical sensor disc correctly.
2) Keep the distance of more than 30 cm apart from the
camcoder.
3) Work on the LCD screen side of the camcoder (opposite
side of the drive).
Note: Laser light of the equipment is focused by the object lens
in the optical pick-up so that the light focuses on the reflec-
tion surface of the disc.
Therefore, be sure to keep your eyes more then 30 cm apart
from the object lens when you check the emission of laser
diode.
tion surface of the disc.
Therefore, be sure to keep your eyes more then 30 cm apart
from the object lens when you check the emission of laser
diode.
Fig. 6-2-4
2-1-2.
How to Set Optical Sensor Disc
1) Before setting the optical sensor disc, remove a lug on the sensor
side of the disc.
Fig. 6-2-2
2) Push in the optical sensor disc until it clicks same as when a
disc is set, and adjust the position so that the cable from the
sensor comes just above the pickup lens, as shown below.
After positioning, fix the disc with a tape so that it does not
rotate.
sensor comes just above the pickup lens, as shown below.
After positioning, fix the disc with a tape so that it does not
rotate.
Fig. 6-2-3
Remove this lug
This part should come just above the pickup
Fix with a tape
Pickup Lens (Laser Diode)
6-36
HDR-UX1/UX1E_ADJ
Table 6-2-1
Note 3: If the DVD-R Disc for Self Jitter, DVD-RW Reference + DOW Disc and DVD+R Self Disc exceeds the use limit, the following
message will be displayed. Replace it with a new disc and click the [OK] button in the message window.
Fig. 6-2-5
2-1-4.
Alignment disc
To diagnose and adjust the drive block, the discs listed in the following table are used.
Note 1: Use the specified disc that matches each diagnostic and adjustment item. (A message is displayed by the AUDIT)
Note 1: Use the specified disc that matches each diagnostic and adjustment item. (A message is displayed by the AUDIT)
If a wrong disc is used, the disc could be destroyed and could not be reused.
Note 2: Handle the disc with care, and before use, check if the disc is scratched or dirty.
Name
DVD-R Disc
for Self Jitter
for Self Jitter
DVD-RW
Reference + DOW
Disc
Reference + DOW
Disc
DVD+R
Reference Disc
Reference Disc
DVD+R
Self Disc
Self Disc
Use
Diagnosis and adjustment of DVD-R
Diagnosis and adjustment of DVD-RW
Adjustment of DVD+R
Diagnosis and adjustment of DVD+R
Remark
This disc can be used about 128 times for the diagnosis and
adjustment. (Note 3)
adjustment. (Note 3)
This disc can be used about 1330 times for the diagnosis and
adjustment. (Note 3)
adjustment. (Note 3)
Useable counts are limitless, unless scratched
This disc can be used about 64 times for the diagnosis and
adjustment. (Note 3)
adjustment. (Note 3)
6-37
HDR-UX1/UX1E_ADJ
2-2.
AUDIT (Drive Adjustment Program)
2-2-1.
Installation Method
Extract the compressed file in the ZIP format. If the extracted file (AUDIT for UX1.msi) is executed, the installer will start. Perform the
installation following the instructions given on the screen of the installer.
installation following the instructions given on the screen of the installer.
2-2-2.
AUDIT Starting Method
Click the [Start] button on the task bar, and from the [Programs], click [AUDIT for Service] – [AUDIT for UX1], and the AUDIT will start. The
SeusEX starts simultaneously with the start of AUDIT, and the operation screen appears only for a moment.
Again, the SeusEX starts and the operation screen is displayed, and after it is minimized for display at the lower left of the desktop, the
AUDIT operation screen appears. If the SeusEX cannot start (because, for instance, the HASP key is not connected to the PC), the AUDIT
also does not start.
SeusEX starts simultaneously with the start of AUDIT, and the operation screen appears only for a moment.
Again, the SeusEX starts and the operation screen is displayed, and after it is minimized for display at the lower left of the desktop, the
AUDIT operation screen appears. If the SeusEX cannot start (because, for instance, the HASP key is not connected to the PC), the AUDIT
also does not start.
2-2-3.
Description of Screen
Fig. 6-2-6
1. Diagnosis section
2. Adjustment section
3. Comment display section
4. Status display section
6. [SET] button
7. Menu section
5. [STOP] button
8. Caution display
section
1.XX
Click on the first or last page to see other HDR-UX1 / HDR-UX1E (serv.man4) service manuals if exist.