DOWNLOAD Sony HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man2) Service Manual ↓ Size: 8.93 MB | Pages: 121 in PDF or view online for FREE

Model
HDR-SR5 HDR-SR5C HDR-SR5E HDR-SR7 HDR-SR7E HDR-SR8 HDR-SR8E (serv.man2)
Pages
121
Size
8.93 MB
Type
PDF
Document
Service Manual
Brand
Device
Movie / LEVEL 2
File
hdr-sr5-hdr-sr5c-hdr-sr5e-hdr-sr7-hdr-sr7e-hdr-sr8.pdf
Date

Sony HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man2) Service Manual ▷ View online

1-3
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-3. METHOD OF COPING WITH SHIFT LENS ERROR (SR7/SR7E/SR8/SR8E)
about 330 msec
Fig. 2
Change in output voltage of R5792 on the LD-228 board
Note: The length of low section will vary a little depending on the
conditions.
Fig. 1
Measurement points on the LD-228 board and the VC-504 board
1-3-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred (SR7/SR7E/SR8/SR8E)
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-228 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1803 of VC-504 board) periphery.
Note: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
IC1803
R1846
IC1803
R1846
R5792
IC5703
R5721
R5737
LD-228 BOARD (SIDE A)
VC-504 BOARD (SIDE A)
1-4
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-3-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred (SR7/SR7E/SR8/SR8E)
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
Procedure
1
11
80
6BB2
01
Write the data.
2
11
80
7D46
F0
Write the data.
3
11
80
7D48
01
Write the data. (Note 1)
4
11
80
7D48
00
Write the data.
5
11
80
7D46
10
Write the data.
6
11
80
7D48
01
Write the data. (Note 1)
7
11
80
7D48
00
Write the data.
8
11
80
6BB2
00
Write the data.
9
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
10
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5721 in the
periphery of IC5703 on the LD-228 board to check the output voltage varies.
11
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
12
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703
13
on the LD-228 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14
change as shown in Fig. 2, inspect the camera control circuit (IC1803 of VC-504 board) pe
riphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 80, address:
7D48, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
1-5
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-3-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred (SR7/SR7E/SR8/SR8E)
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
Procedure
1
11
80
6BB2
01
Write the data.
2
11
80
7D47
F0
Write the data.
3
11
80
7D49
01
Write the data. (Note 1)
4
11
80
7D49
00
Write the data.
5
11
80
7D47
10
Write the data.
6
11
80
7D49
01
Write the data. (Note 1)
7
11
80
7D49
00
Write the data.
8
11
80
6BB2
00
Write the data.
9
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
10
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5737 in the
periphery of IC5703 on the LD-228 board to check the output voltage varies.
11
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
12
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703
13
on the LD-228 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
14
change as shown in Fig. 2, inspect the camera control circuit (IC1803 of VC-504 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 80, address:
7D49, data: 00, and then retry.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
1-3-4. E : 62 : 20 [Abnormality of Thermistor] Occurred (SR7/SR7E/SR8/SR8E)
Order
Procedure
1
Turn the power ON.
2
Check that R1846 in the periphery of IC1803 on the VC-504 board is 0 
Ω and energizes. If it is not energizes, replace the R1846.
When R1846 is 0 
Ω and energizes, replace the lens block (Note).
3
Check that no error occurs, after replacing the lens block and performing the necessary adjustment. If an error occurs, inspect
the camera control circuit (IC1803 of VC-504 board) periphery.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
1-6
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-4. PRECAUTION  ON  REPLACING  THE  VC-504 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-5. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by execution of “Clear All record-data”.
Note:
 For “Clear All record-data”, refer to Service Manual, ADJ (“7. Record Data” of “2-2. SERVICE MODE”).
Page of 121
Display

Click on the first or last page to see other HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man2) service manuals if exist.