DOWNLOAD Sony HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man2) Service Manual ↓ Size: 8.93 MB | Pages: 121 in PDF or view online for FREE

1-1

HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2

In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.

Use the AC power adaptor (AC-L200/L200B).

When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the Viewfinder or the LCD
screen what to do. This function consists of two display; self-
diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.

When problems occur while the unit is operating, the counter of the
Viewfinder or the LCD screen shows a 4-digit display consisting of
an alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.

1 1

3 1

C

Repaired by:

Refer to “1-2-3. Self-diagnosis Code Table”.

Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2Hz

C : Corrected by customer
H : Corrected by dealer
E : Corrected by service

engineer

Viewfinder or LCD screen

C : 3 1 : 1 1

1-2

HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2

C

C

C

C

E

E

E

E

E

E

E

E

E

E

E

E

E

E

Block

Function

0

4

1

3

1

3

3

2

2

0

3

1

6

1

6

1

6

2

6

2

6

2

6

2

6

2

6

2

6

2

6

2

9

1

9

4

Detailed

Code

0

0

0

1

0

2

6

0

0

0

0

0

1

0

1

1

0

0

0

1

0

2

0

3

1

0

1

1

1

2

2

0

0

1

0

0

Symptom/State

Non-standard battery is used.

“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.

Disc access error

Difficult to adjust focus
(Cannot initialize focus)

EEPROM data are rewritten.

Drive fault

Zoom operations fault
(Cannot initialize zoom lens.)

The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.

Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)

Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)

Abnormality of IC for steadyshot.

IC for steadyshot and micro controller
communication abnormality among.

Shift lens initializing failure.

Shift lens overheating (Pitch).

Shift lens overheating (Yaw).

Abnormality of thermistor.

Abnormality when flash is being charged.

Fault of writing to or erasing the
flashmemory

Self-diagnosis Code

Repaired b

y:

Correction

Use the InfoLITHIUM battery.

Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.

Remove the power source. Reconnect it again and operate your
camcorder again

Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin ql, wa of
CN5302 on the LD-228 board: SR5/SR5C/SR5E, pin qh, qk of
CN5301 on the LD-228 board: SR7/SR7E/SR8/SR8E). If it is
OK, check the focus motor drive IC (IC5404 on the LD-228
board).

Make EEPROM data correct value.

Inspect or replacement of the hard disk drive.

Inspect the lens block zoom MR sensor (pin qh, qk of CN5302
on the LD-228 board: SR5/SR5C/SR5E, pin w;, wa of CN5301
on the LD-228 board: SR7/SR7E/SR8/SR8E) when zooming is
performed when the zoom lever is operated, and the zoom motor
drive circuit (IC5404 on the LD-228 board) when zooming is not
performed.

Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.

Inspect PITCH angular velocity sensors (SE8202 on the CM-076
board: SR5/SR5C/SR5E, SE7202 on the CM-077 board: SR7/
SR7E/SR8/SR8E) peripheral circuits.

Inspect YAW angular velocity sensors (SE8201 on the CM-076
board: SR5/SR5C/SR5E, SE7201 on the CM-077 board: SR7/
SR7E/SR8/SR8E) peripheral circuits.

Refer to [1-3-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
Occurred] (SR7/SR7E/SR8/SR8E only).

Inspect the steadyshot circuit (IC5703 on the LD-228 board)
(SR7/SR7E/SR8/SR8E only).

SR7/SR7E/SR8/SR8E only:
1. Inspect the EEPROM (IC1804 on the VC-504 board).
2. Perform the STEADY HALL adjustment. (Note 1)
3. Replace the lens block. (Note 2)

Refer to [1-3-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
Occurred] (SR7/SR7E/SR8/SR8E only).

Refer to [1-3-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
Occurred] (SR7/SR7E/SR8/SR8E only).

Refer to [1-3-4. E : 62 : 20 (Abnormality of Thermistor)
Occurred] (SR7/SR7E/SR8/SR8E only).

Checking of flash unit or replacement of flash unit.

Inspect the flash memory (IC2201 on the VC-504 board).

Note 1: Perform adjustment by referring to “STEADY HALL Adjustment” in Service Manual, ADJ. After the adjustment, be sure

to perform “GYRO Sensor Sensitivity Adjustment”.

Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.

1-3

HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2

about 330 msec

Note: The length of low section will vary a little depending on the

conditions.

Order

Procedure

1

Turn the power OFF.

2

While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-228 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.

3

If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1803 of VC-504 board) periphery.

Note: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.

IC1803

R1846

IC1803

R1846

R5792

IC5703

R5721

R5737

LD-228 BOARD (SIDE A)

VC-504 BOARD (SIDE A)

1-4

HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2

Connect by the SeusEX and perform the following process.

Order Block Page Address Data

Procedure

1

11

80

6BB2

01

Write the data.

2

11

80

7D46

F0

Write the data.

3

11

80

7D48

01

Write the data. (Note 1)

4

11

80

7D48

00

Write the data.

5

11

80

7D46

10

Write the data.

6

11

80

7D48

01

Write the data. (Note 1)

7

11

80

7D48

00

Write the data.

8

11

80

6BB2

00

Write the data.

9

Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.

10

While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5721 in the
periphery of IC5703 on the LD-228 board to check the output voltage varies.

11

If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.

12

Turn the power OFF.

While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703

13

on the LD-228 board, turn the power ON to check that the output voltage immediately after the
power on change as shown in Fig. 2.

If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not

14

change as shown in Fig. 2, inspect the camera control circuit (IC1803 of VC-504 board) pe
riphery.

Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 80, address:

7D48, data: 00, and then retry.

Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.

After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.