Sony HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man2) Service Manual ▷ View online
1-18
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
HDR-SR8
(Japanese Model)
(Japanese Model)
Part No.
A-1317-534-A
Description
SERVICE, CABINET (G (SR8)) (J)
HDR-SR8
(US Model)
(US Model)
Part No.
A-1317-535-A
Description
SERVICE,CABINET (G (SR8)) (U2)
HDR-SR8
(Canadian Model)
(Canadian Model)
Part No.
A-1317-538-A
Description
SERVICE, (G (SR8)) (CA2)
HDR-SR8
(E, Tourist Models)
(E, Tourist Models)
Part No.
A-1317-539-A
Description
SERVICE, (G (SR8)) (E23)
Serial No.
*Manufacturing year
*Affix the label
*Affix the label
HDR-SR8
(Korean Model)
(Korean Model)
Part No.
A-1317-540-A
Description
SERVICE, (G (SR8)) (KR2)
*Affix the label
Serial No.
*Factory
*Manufacturing year
Serial No.
Serial No.
Serial No.
*Manufacturing year
(ENGLISH)
1-11. PRECAUTION ON REPLACING
1-11. PRECAUTION ON REPLACING
THE CABINET (G) ASSY
(HDR-SR8)
(HDR-SR8)
The model display adopts the laser printing method.Therefore, the
cabinet (G) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
cabinet (G) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note1: After replacing the cabinet (G) assy, the serial number for it
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
Note 2: When replacing the cabinet (G) assy for US, affix the
“Manufacturing year” label and the “Factory” label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G) assy.
“Manufacturing year” label and the “Factory” label on the specified
location as shown in the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G) assy.
Note 3: When replacing the cabinet (G) assy for Korea, affix the
“Manufacturing year” label on the specified location as shown in
the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G) assy.
“Manufacturing year” label on the specified location as shown in
the figure.
The replacement caution label and inset (how to affix) are supplied
together with the cabinet (G) assy.
(JAPANESE)
1-11. キャビネット(G)組立交換時の注意
1-11. キャビネット(G)組立交換時の注意
(HDR-SR8)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット(G)組立は仕向けにより異な
ります。類似の表示もありますので，該当するものを選ん
で注文して下さい。
注意1: キャビネット(G)組立交換後はシリアルナンバーが
サービス専用のシリアルナンバーに変更されます。お客様
への案内と修理データのシリアルナンバー変更を行ってく
ださい。
注意2 : U S 仕向けキャビネット( G ) 組立を交換した際は
「製造年月」を表すラベルと，「製造所」を表すラベルを
図の指定位置に貼り付けてください。
なお，キャビネット(G)組立には時期表示ラベル，投げ込み
(ラベル貼り方)がセットで供給されます。
注意3: Korean仕向けキャビネット(G)組立を交換した際
は，「製造年月」を表すラベルを図の指定位置に貼り付け
てください。
なお，キャビネット(G)組立には時期表示ラベル，投げ込み
(ラベル貼り方)がセットで供給されます。
1-19E
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-SR8E
(E, Hong Kong, Australian, Tourist Models)
(E, Hong Kong, Australian, Tourist Models)
Part No.
A-1317-541-A
Description
SERVICE, (G (SR8E)) (E34)
HDR-SR8E
(UK Model)
(UK Model)
Part No.
A-1317-542-A
Description
SERVICE, (G (SR8E)) (CEH)
HDR-SR8E
(Chinese Model)
(Chinese Model)
Part No.
A-1317-543-A
Description
SERVICE, (G (SR8E)) (CN2)
HDR-SR8E
(AEP Model)
(AEP Model)
Part No.
A-1317-544-A
Description
SERVICE, (G (SR8E)) (CEN)
Serial No.
Serial No.
Serial No.
Serial No.
(ENGLISH)
1-12. PRECAUTION ON REPLACING
1-12. PRECAUTION ON REPLACING
THE CABINET (G) ASSY
(HDR-SR8E)
(HDR-SR8E)
The model display adopts the laser printing method.Therefore, the
cabinet (G) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
cabinet (G) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note1: After replacing the cabinet (G) assy, the serial number for it
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
(JAPANESE)
1-12. キャビネット(G)組立交換時の注意
1-12. キャビネット(G)組立交換時の注意
(HDR-SR8E)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット(G)組立は仕向けにより異な
ります。類似の表示もありますので，該当するものを選ん
ります。類似の表示もありますので，該当するものを選ん
で注文して下さい。
注意1: キャビネット(G)組立交換後はシリアルナンバーが
サービス専用のシリアルナンバーに変更されます。お客様
サービス専用のシリアルナンバーに変更されます。お客様
への案内と修理データのシリアルナンバー変更を行ってく
ださい。
ださい。
2-1
2. DISASSEMBLY
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
Short-circuit between the two points with the
short jig about 10 seconds.
To avoid the spark with the metal plate,
wrap the short jig with the insulation tape.
R:1 k
Ω
/1 W
(Part code: 1-215-869-11)
C5206
(Charging
Capacitor)
(Charging
Capacitor)
ST-175
Board
Board
DISCHARGING OF THE ST-175 BOARD’S CHARGING CAPACITOR (C5206)
The charging capacitor (C5206) of the ST-175 board is charged
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
up to the maximum 300 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω
/1 W
Wrap insulating tape.
Tweezers etc.
Harness
(coaxial cable)
(coaxial cable)
When disconnecting the harness (coaxial cable), do not pull the
harness part but pull off the connector body with tweezers etc.
harness part but pull off the connector body with tweezers etc.
NOTE FOR DISCONNECTION THE HARNESS (COAXIAL CABLE)
2-2
HDR-SR5/SR5C/SR5E/SR7/SR7E/SR8/SR8E_L2
2-1. IDENTIFYING PARTS
2-2-1. OVERALL SECTION-1
- Cabinet (G) Assy
- HDD
- Bottom Cabinet Block
- HDD
- Bottom Cabinet Block
2-2-2. OVERALL SECTION-2 (SR7/SR7E/SR8/SR8E)
2-2-3. OVERALL SECTION-2 (SR5/SR5C/SR5E)
2-2-3. OVERALL SECTION-2 (SR5/SR5C/SR5E)
- Cabinet (T(255))
- Cabinet (R) Section
- BT Panel Block
- EVF Block (SR7/SR7E/SR8/SR8E)
- Cabinet (R) Section
- BT Panel Block
- EVF Block (SR7/SR7E/SR8/SR8E)
2-2-4. OVERALL SECTION-3
- Control Switch Block
(PS25500)
- Cabinet (F) Block
(PS25500)
- Cabinet (F) Block
2-2-5. CABINET (L) SECTION-1
- VC-504 Board
- Main frame section
- Main frame section
2-2-10. CABINET (R) SECTION
- Loud Speaker
- CK-183 Board
- LCD Panel Block
- CK-183 Board
- LCD Panel Block
Cabinet (R) Section
⋅
CK-183 Board
⋅
PD-324 Board
Cabinet (L) Section
⋅
VC-504 Board
⋅
JK-342 Board
EVF Block
⋅
BL-013 Board
Lens Section
(SR7/SR7E/SR8/SR8E)
(SR7/SR7E/SR8/SR8E)
⋅
ST-175 Board
⋅
LD-228 Board
⋅
CM-077 Board
Lens Section
(SR5/SR5C/SR5E)
(SR5/SR5C/SR5E)
⋅
ST-175 Board
⋅
LD-228 Board
⋅
CM-076 Board
Bottom Cabinet
Block
Block
Cabinet (G) Assy
HDD
BT Panel Block
⋅
MS-374 Board
Control Switch Block
(PS25500)
(PS25500)
- DISASSEMBLY FLOW -
2-2-7. CABINET (F) BLOCK
- Lens Section
- Lens Barrier Unit
- Lens Barrier Unit
2-2-8. LENS SECTION (SR7/SR7E/SR8/SR8E)
2-2-9. LENS SECTION (SR5/SR5C/SR5E)
2-2-9. LENS SECTION (SR5/SR5C/SR5E)
- ST-175 Board
- LD-228 Board
- Flash Unit (FL25500)
- LD-228 Board
- Flash Unit (FL25500)
2-2-6. CABINET (L) SECTION-2
- JK-342 Board
2-2-11. LCD PANEL BLOCK
- Hinge Block
- LCD
- PD-324 Board
- LCD
- PD-324 Board
SR7/SR7E/
SR8/SR8E
SR8/SR8E
Click on the first or last page to see other HDR-SR5 / HDR-SR5C / HDR-SR5E / HDR-SR7 / HDR-SR7E / HDR-SR8 / HDR-SR8E (serv.man2) service manuals if exist.