Sony HDR-HC3 / HDR-HC3E / HDR-HC3EK / HDR-HC3K (serv.man4) Service Manual ▷ View online
6-59
HDR-HC3/HC3E/HC3K/HC3EK_ADJ
32. Steady Shot Check
RadarW
RadarW
RadarW
RadarW
RadarW
Precautions on the Parts Replacement
There are two types of repair parts.
There are two types of repair parts.
Type A
ECN-03MA
Type B
ECN-03MB
Replace the broken sensor with a same type sensor. If replace with
other type parts, the image will vibrate up and down or left and
right during hand-shake correction operations.
other type parts, the image will vibrate up and down or left and
right during hand-shake correction operations.
Precautions on Angular Velocity Sensor
The sensor incorporates a precision oscillator. Handle it with care
as if it dropped, the balance of the oscillator will be disrupted and
operations will not be performed properly.
The sensor incorporates a precision oscillator. Handle it with care
as if it dropped, the balance of the oscillator will be disrupted and
operations will not be performed properly.
Subject
Not required
Measurement Point
Displayed data of page: 1 (Note 1)
Measuring Instrument
Adjusting remote commander
Specified value
PITCH data: 2680 to 5080
YAW data: 2680 to 5080
YAW data: 2680 to 5080
Note 1:
The right four digits of the page: 1 displayed data of the
adjusting remote commander.
adjusting remote commander.
1 : XX : XX
Displayed data
Note 2:
Check that the data of page: 0, address: 10 is “00”.
Switch setting
1) ZOOM ..................................................................... TELE end
2) STEADY SHOT (Menu setting) ....................................... ON
1) ZOOM ..................................................................... TELE end
2) STEADY SHOT (Menu setting) ....................................... ON
Checking method:
Order Page Address Data
Procedure
PITCH sensor output check (SE7702 of CM-071 board)
1
0
03
11
2
1
With the set in still state,
check that the displayed data
(Note 1) satisfies the PITCH
data specified value.
check that the displayed data
(Note 1) satisfies the PITCH
data specified value.
YAW sensor output check (SE7701 of CM-071 board)
3
0
03
12
4
1
With the set in still state,
check that the displayed data
(Note 1) satisfies the YAW
data specified value.
check that the displayed data
(Note 1) satisfies the YAW
data specified value.
5
0
03
00
Steady shot operation check
6
Shake the set vertically and
horizontally to check that the
steady shot function operates
normally.
horizontally to check that the
steady shot function operates
normally.
6-60
HDR-HC3/HC3E/HC3K/HC3EK_ADJ
Adjusting method for NTSC model:
Order Page Address Data
Procedure
1
0
01
01
2
3
03
FF
3
3
71
01
Press PAUSE (Write) button.
4
C
66
00
Press PAUSE (Write) button.
5
3
01
5A
Press PAUSE (Write) button.
(Note 4)
(Note 4)
6
3
02
Check the data changes to “00”.
7
3
03
Check the data is “00”. (Note 2)
8
C
34
Read the data and this data is
named D
named D
34
.
9
Convert D
34
to decimal
notation, and obtain D
34
’.
(Note 3)
10
Calculate D
35
’ using
following equations.
(decimal calculation)
D
(decimal calculation)
D
35
’ = D
34
’ + 10
11
Convert D
35
’ to a hexadeci-
mal number, and obtain D
35
.
(Note 3)
12
C
35
D
35
Press PAUSE (Write) button.
13
C
3C
Read the data and this data is
named D
named D
3C
.
14
C
77
D
3C
Press PAUSE (Write) button.
15
C
66
41
Press PAUSE (Write) button.
16
3
70
10
Press PAUSE (Write) button.
17
3
70
Check the data changes to “11”.
18
0
01
00
Note 4:
The adjustment data will be automatically input to page:
C, address: 34 and 3C.
C, address: 34 and 3C.
1-4.
ELECTRONIC VIEWFINDER SYSTEM
ADJUSTMENTS
ADJUSTMENTS
Before perform the viewfinder system adjustments, check the data
of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
Note 1:
Taken an extreme care not to destroy the liquid crystal
display module by static electricity when replacing it.
display module by static electricity when replacing it.
Note 2:
Perform the following data setting before the viewfinder
system adjustments.
1) Select page: 3, address: C4, and set data: 67.
2) Select page: 3, address: C5, and set data: 01.
Reset the data after completing adjustment.
1) Select page: 3, address: C4, and set data: 00.
2) Select page: 3, address: C5, and set data: 00.
system adjustments.
1) Select page: 3, address: C4, and set data: 67.
2) Select page: 3, address: C5, and set data: 01.
Reset the data after completing adjustment.
1) Select page: 3, address: C4, and set data: 00.
2) Select page: 3, address: C5, and set data: 00.
1.
EVF Automatic Adjustment (VF-175 board)
RadarW
RadarW
RadarW
This adjustment does the following items automatically.
VCO Adjustment
Contrast Adjustment
Contrast Adjustment
Mode
VTR stop (PLAY/EDIT mode)
Signal
No signal
Adjustment Page
C
Adjustment Address
34, 35 (VCO Adjustment)
3C, 77 (Contrast Adjustment)
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
If the data change to “01”, adjustment has error. Con-
tents of error is written into page: 3, address: C6. See the
following table.
tents of error is written into page: 3, address: C6. See the
following table.
Data of page: 3, address: C6 Contents of error
5E
VCO adjustment error
61
Contrast adjustment error
Note 3:
Refer to Table 6-4-1. “Hexadecimal-decimal conversion
table”.
table”.
6-61
HDR-HC3/HC3E/HC3K/HC3EK_ADJ
2.
White Balance Adjustment (VF-175 board)
Correct the white balance.
If deviated, the EVF screen color cannot be reproduced.
If deviated, the EVF screen color cannot be reproduced.
Mode
VTR stop (PLAY/EDIT mode)
Signal
No signal
Measurement Point
Check on EVF screen
Measuring Instrument
Adjustment Page
C
Adjustment Address
3A, 3B
Specified Value
EVF screen must not be colored
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Check the white balance only when replacing the fol-
lowing parts. If necessary, adjust them.
1. LCD panel
2. Light induction plate
3. IC8101
lowing parts. If necessary, adjust them.
1. LCD panel
2. Light induction plate
3. IC8101
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
3
71
01
Press PAUSE (Write) button.
3
C
3A
92
Press PAUSE (Write) button.
4
C
3B
7E
Press PAUSE (Write) button.
5
Check that the EVF screen is
not colored. If not colored,
proceed to step 6.
not colored. If not colored,
proceed to step 6.
6
C
3A
Change the data so that the
3B
EVF screen is not colored.
(Note 3)
(Note 3)
7
3
70
10
Press PAUSE (Write) button.
8
3
70
Check the data changes to “11”.
9
0
01
00
Note 3:
To write in the non-volatile memory (EEPROM), press
the PAUSE (Write) button each time to set the data.
the PAUSE (Write) button each time to set the data.
Adjusting method for PAL model:
Order Page Address Data
Procedure
1
0
01
01
2
3
03
FF
3
3
71
01
Press PAUSE (Write) button.
4
C
66
00
Press PAUSE (Write) button.
5
3
01
5A
Press PAUSE (Write) button.
(Note 5)
(Note 5)
6
3
02
Check the data changes to “00”.
7
3
03
Check the data is “00”. (Note 2)
8
C
35
Read the data and this data is
named D
named D
35
.
9
Convert D
35
to decimal
notation, and obtain D
35
’.
(Note 3)
10
Calculate D
34
’ using
following equations.
(decimal calculation)
D
(decimal calculation)
D
34
’ = D
35
’
− 10
11
Convert D
34
’ to a hexadeci-
mal number, and obtain D
34
.
(Note 3)
12
C
34
D
34
Press PAUSE (Write) button.
13
C
3C
Read the data and this data is
named D
named D
3C
.
14
C
77
D
3C
Press PAUSE (Write) button.
15
C
66
41
Press PAUSE (Write) button.
16
3
70
10
Press PAUSE (Write) button.
17
3
70
Check the data changes to “11”.
18
0
01
00
Note 5:
The adjustment data will be automatically input to page:
C, address: 35 and 3C.
C, address: 35 and 3C.
6-62
HDR-HC3/HC3E/HC3K/HC3EK_ADJ
Adjusting method for NTSC model:
Order Page Address Data
Procedure
1
0
01
01
2
3
03
FF
3
3
71
01
Press PAUSE (Write) button.
4
C
65
00
Press PAUSE (Write) button.
5
3
01
5A
Press PAUSE (Write) button.
(Note 4)
(Note 4)
6
3
02
Check the data changes to “00”.
7
3
03
Check the data is “00”. (Note 2)
8
C
45
Read the data and this data is
named D
named D
45
.
9
Convert D
45
to decimal
notation, and obtain D
45
’.
(Note 3)
10
Calculate D
46
’ using
following equations.
(decimal calculation)
D
(decimal calculation)
D
46
’ = D
45
’ + 10
11
Convert D
46
’ to a hexadeci-
mal number, and obtain D
46
.
(Note 3)
12
C
46
D
46
Press PAUSE (Write) button.
13
C
4D
Read the data and this data is
named D
named D
4D
.
14
C
76
D
4D
Press PAUSE (Write) button.
15
C
65
41
Press PAUSE (Write) button.
16
3
70
10
Press PAUSE (Write) button.
17
3
70
Check the data changes to “11”.
18
0
01
00
Note 4:
The adjustment data will be automatically input to page:
C, address: 45 and 4D.
C, address: 45 and 4D.
1-5.
LCD SYSTEM ADJUSTMENTS
Before perform the LCD system adjustments, check that the data
of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
Note 1:
Taken an extreme care not to destroy the liquid crystal
display module by static electricity when replacing it.
display module by static electricity when replacing it.
Note 2:
Set the “LCD BRIGHT”, “LCD COLOR” to the center
with the menu settings of the touch panel.
with the menu settings of the touch panel.
Note 3:
Open the LCD panel during the LCD system adjustment.
1.
LCD Automatic Adjustment (PD-276 board)
RadarW
RadarW
RadarW
This adjustment does the following items automatically.
VCO Adjustment
Contrast Adjustment
Contrast Adjustment
Mode
VTR stop (PLAY/EDIT mode)
Signal
No signal
Adjustment Page
C
Adjustment Address
45, 46 (VCO Adjustment)
4D, 76 (Contrast Adjustment)
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
If the data change to “01”, adjustment has error. Con-
tents of error is written into page: 3, address: C6. See the
following table.
tents of error is written into page: 3, address: C6. See the
following table.
Data of page: 3, address: C6 Contents of error
58
VCO adjustment error
60
Contrast adjustment error
Note 3:
Refer to Table 6-4-1. “Hexadecimal-decimal conversion
table”.
table”.
Click on the first or last page to see other HDR-HC3 / HDR-HC3E / HDR-HC3EK / HDR-HC3K (serv.man4) service manuals if exist.