Sony HDR-FX1000 / HDR-FX1000E (serv.man3) Service Manual ▷ View online
6-7
HDR-FX1000/FX1000E_ADJ
Fig. b (monitor TV picture)
1-1-3.
Precaution
1.
Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
Color bar chart (Color reproduction adjustment frame)
Fig. a
(VIDEO OUT jack output
waveform)
(VIDEO OUT jack output
waveform)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a and
the monitor TV display shown in Fig. b.
obtain the output waveform shown in Fig. a and
the monitor TV display shown in Fig. b.
Fig. 6-1-3
1.
CAMERA/VCR switch ......................................... CAMERA
2.
FOCUS switch ............................................................. AUTO
3.
ND FILTER .................................................................... OFF
4.
SHUTTER SPEED ..................................................... AUTO
5.
MENU settings
CAMERA SET menu
BACK LIGHT ........................................................ OFF
SPOT LIGHT .......................................................... OFF
D. EXTENDER ...................................................... OFF
SPOT LIGHT .......................................................... OFF
D. EXTENDER ...................................................... OFF
2.
Order of Adjustments
Basically carry out adjustments in the order given.
3.
Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, ad-
just the picture frame as shown in Fig. 6-1-3. (Color reproduc-
tion adjustment frame)
just the picture frame as shown in Fig. 6-1-3. (Color reproduc-
tion adjustment frame)
2) Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations dur-
ing this time)
clear chart in its place. (Do not perform zoom operations dur-
ing this time)
IN/OUT REC menu
REC FORMAT ............................................. HDV1080i
H
A=B
A B
B A
Enlargement
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
C = D = 0
V
C
D
Y
ello
w
Cy
an
Blue
Green
White
Magenta
Red
CRT picture frame
Electronic beam scanning frame
6-8
HDR-FX1000/FX1000E_ADJ
4.
Setting Distance between Pattern Box and Camera
Set the distance from the front of the lens to the pattern box as shown in Fig. 6-1-4.
Fig. 6-1-4
5.
Precautions When Using Pattern Box
1) It takes about 30 minutes for pattern box to stabilize its brightness.
Turn on the pattern box 30 minutes before the adjustment starts.
2) Make arrangement so that the outside light does not enter the chart surface in the pattern box.
Also, place a board between chart and camera, and make a hole at the lens part of the board so that the camera is not reflected in the
shot image screen.
(Adjustment may not be performed correctly due to the influence of outside light.)
shot image screen.
(Adjustment may not be performed correctly due to the influence of outside light.)
Example 1:
Place a box to block a section between pattern box and camera.
Example 2:
Place a board having a hole in front of the camera and cover the pattern box and camera with a blackout curtain
3) Control of color chart
The color chart will fade if it is exposed to direct sunlight or strong light.
Since the fading of color chart progresses even with the light in the pattern box, remove and store the color chart when it is not used.
Remove the color chart and store it.
Store the color chart in a place not exposed to direct light, avoiding high temperature and humidity.
Use the color chart for about three years, and afterward replace it with a new chart.
Since the fading of color chart progresses even with the light in the pattern box, remove and store the color chart when it is not used.
Remove the color chart and store it.
Store the color chart in a place not exposed to direct light, avoiding high temperature and humidity.
Use the color chart for about three years, and afterward replace it with a new chart.
Pattern box
Front of the lens
Make the hole of the same
size as the lens.
size as the lens.
Make the hole of the same
size as the pattern box.
size as the pattern box.
L = 17 cm (PTB-1450)
L
Camera
Pattern box
Front of the lens
Board that opens hole
to lens part
to lens part
L = 17 cm (PTB-1450)
L
Camera
Cover with a blackout curtain
Pattern box
Front of the lens
L = 17 cm (PTB-1450)
L
Camera
6-9
HDR-FX1000/FX1000E_ADJ
1-2.
INITIALIZATION OF EVR DATA
Note 1:
Pages used for the EVR consists of 45 pages. There are
7C, 7E, 7F, 8, 9, A, B, C, D, 13, 18, 1A, 1B, 1C, 1D, 1E,
6D, 6E, 6F, 8C, 8D, 8E, 8F, 9D, 9E, 9F, AD, AE, AF,
BE, BF, C2, C3, C4, C5, C6, C7, C8, C9, CA, CB, CC,
CD, CE, CF, pages.
7C, 7E, 7F, 8, 9, A, B, C, D, 13, 18, 1A, 1B, 1C, 1D, 1E,
6D, 6E, 6F, 8C, 8D, 8E, 8F, 9D, 9E, 9F, AD, AE, AF,
BE, BF, C2, C3, C4, C5, C6, C7, C8, C9, CA, CB, CC,
CD, CE, CF, pages.
Note 2:
If 2-digit page is selected, set higher-order digit to page:
0, address: 10 as data, and then select lower-order digit
by a usual method.
e.g.: Set data: 06 to page: 0, address: 10, and then select
page: D. Thus, the page 6D can be selected.
0, address: 10 as data, and then select lower-order digit
by a usual method.
e.g.: Set data: 06 to page: 0, address: 10, and then select
page: D. Thus, the page 6D can be selected.
1-2-1.
Initialization of A, B, D, 1A, 1B Page Data
Note:
Check that the data of page: 0, address: 10 is “00”.
1.
Initializing of A, B, D, 1A, 1B Page Data
Note:
If the A, B, D, 1A, 1B page data has been initialized, the
following adjustments need to be performed again.
1) Modification of A, B, D, 1A, 1B page data
2) Level vial adjustment
following adjustments need to be performed again.
1) Modification of A, B, D, 1A, 1B page data
2) Level vial adjustment
Adjustment Page
A
Adjustment Address
10 to FF
Adjustment Page
B
Adjustment Address
00 to FF
Adjustment Page
D
Adjustment Address
10 to FF
Adjustment Page
1A
Adjustment Address
00 to FF
Adjustment Page
1B
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
2
EA
Check the bit1 value.
1: NTSC model
0: PAL model
0: PAL model
4
7
04
Set the following data
00: NTSC model
01: PAL model
Set the following data
20: Initializing A page
21: Initializing B page
22: Initializing D page
23: Initializing 1A page
24: Initializing 1B page
21: Initializing B page
22: Initializing D page
23: Initializing 1A page
24: Initializing 1B page
5
7
01
25: Initializing A and 1A
page
26: Initializing B and 1B
page
28: Initializing A, B, D, 1A
and 1B page
6
7
02
FF
7
7
00
01
Press PAUSE (Write) button.
8
7
02
Check the data changes to
“01”.
“01”.
9
Perform “Modification of A,
B, D, 1A, 1B Page Data”
B, D, 1A, 1B Page Data”
2.
Modification of A, B, D, 1A, 1B Page Data
If the A, B, D, 1A, 1B page data has been initialized, change the
data of the “Fixed data-2” address shown in the following table by
manual input.
data of the “Fixed data-2” address shown in the following table by
manual input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages A, B, D, set data: 00 to page:
0, address: 10, and then select pages A, B, D.
3) If modification of data on pages 1A, 1B, set data: 01 to page:
0, address: 10, and then select pages A, B.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
After the modification of data finished, return the data on page:
0, address: 10 to “00”.
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
the data built in the same model.
Note 1:
If copy the data built in the different model, the cam-
corder may not operate.
corder may not operate.
5) When changing the data, press the PAUSE (Write) button of
the adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
data to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after Completing Modification A, B, D, 1A, 1B
page data:
page data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE (Write) button.
Note 2:
If following symptoms occur after completing of the
“Modification A, B, D, 1A, 1B page data”, check that
the data of the “Fixed data-2” address of A, B, D, 1A, 1B
page are same as those of same model of same destina-
tion.
1) The power is shut off so that unit cannot operate.
“Modification A, B, D, 1A, 1B page data”, check that
the data of the “Fixed data-2” address of A, B, D, 1A, 1B
page are same as those of same model of same destina-
tion.
1) The power is shut off so that unit cannot operate.
6-10
HDR-FX1000/FX1000E_ADJ
5.
D Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the A, B, D, 1A, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, B, D, 1A, 1B Page Data”)
the A, B, D, 1A, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, B, D, 1A, 1B Page Data”)
Address
Initial value
Remark
NTSC PAL
10 to FF
Fixed data-1 (Initialized data)
6.
1A Page table
Note 1:
If reading/writing data on pages 1A, set data: 01 to page:
0, address: 10, and then select pages: A. By this data set-
ting, the pages 1A can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: A. By this data set-
ting, the pages 1A can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the A, B, D, 1A, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, B, D, 1A, 1B Page Data”)
the A, B, D, 1A, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, B, D, 1A, 1B Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to FF
Fixed data-1 (Initialized data)
7.
1B Page table
Note 1:
If reading/writing data on pages 1B, set data: 01 to page:
0, address: 10, and then select pages: B. By this data set-
ting, the pages 1B can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
0, address: 10, and then select pages: B. By this data set-
ting, the pages 1B can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the A, B, D, 1A, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, B, D, 1A, 1B Page Data”)
the A, B, D, 1A, 1B Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of A, B, D, 1A, 1B Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to FF
Fixed data-1 (Initialized data)
3.
A Page table
Note 1:
Check that the data of page: 0, address: 10 is“00”.
Note 2:
Fixed data-1: Initialized data. (Refer to“1. Initializing the
A, B, D, 1A, 1B Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of A, B, D, 1A, 1B Page Data”)
A, B, D, 1A, 1B Page Data”)
Fixed data-2: Modified data. (Refer to“2. Modification
of A, B, D, 1A, 1B Page Data”)
Address
Initial value
Remark
NTSC PAL
10
00
00
Test mode
11 to 17
Fixed data-1 (Initialized data)
18
Fixed data-2
19 to 2E
Fixed data-1 (Initialized data)
2F
Fixed data-2
30
Fixed data-1 (Initialized data)
31
Fixed data-2
32 to EF
Fixed data-1 (Initialized data)
F0 to F3
Fixed data-2
F4, F5
Fixed data-1 (Initialized data)
F6
27
27
F7
DE
DE
F8
28
28
Level vial adj.
F9
18
18
FA
28
28
FB
22
22
FC to FF
Fixed data-1 (Initialized data)
4.
B Page table
Note 1:
Check that the data of page: 0, address: 10 is “00”.
Note 2:
Fixed data-1: Initialized data. (Refer to “1. Initializing
the A, B, D, 1A, 1B Page Data”)
the A, B, D, 1A, 1B Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to B0
Fixed data-1 (Initialized data)
B1
Fixed data-2
B2 to FF
Fixed data-1 (Initialized data)
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2008.11
Click on the first or last page to see other HDR-FX1000 / HDR-FX1000E (serv.man3) service manuals if exist.