DOWNLOAD Sony HDR-FX1 / HDR-FX1E / Q002-HDR1 Service Manual ↓ Size: 9.35 MB | Pages: 77 in PDF or view online for FREE

Model
HDR-FX1 HDR-FX1E Q002-HDR1
Pages
77
Size
9.35 MB
Type
PDF
Document
Service Manual
Brand
Device
Movie / LEVEL 3
File
hdr-fx1-hdr-fx1e-q002-hdr1.pdf
Date

Sony HDR-FX1 / HDR-FX1E / Q002-HDR1 Service Manual ▷ View online

— 2 —
HDR-FX1/FX1E
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1.
Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
 : LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40
°
C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°
C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
— 3 —
HDR-FX1/FX1E
ENGLISH
JAPANESE
ENGLISH
JAPANESE
— 4 —
HDR-FX1/FX1E
TABLE OF CONTENTS
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1.
FRAME PRINTED WIRING BOARD (1/2) ·················· 4-1
FRAME PRINTED WIRING BOARD (2/2) ·················· 4-3
4-2.
SCHEMATIC DIAGRAMS ·········································· 4-53
• CD-522 (R.G.B-CH CCD IMAGER, S/H, AGC)
SCHEMATIC DIAGRAM ···························· 4-53
• DA-033 (DC/DC CONVERTER)
SCHEMATIC DIAGRAM ···························· 4-55
• DB-018 (1/2) (DC IN, CHARGE)
SCHEMATIC DIAGRAM ···························· 4-57
• DB-018 (2/2) (DC/DC CONVERTER)
SCHEMATIC DIAGRAM ···························· 4-59
• VC-367 (1/25) (CCD RF IN)
SCHEMATIC DIAGRAM ···························· 4-61
• VC-367 (2/25) (R.G.B-CH AGC, A/D CONV., TIMING
GENERATOR)
SCHEMATIC DIAGRAM ···························· 4-63
• VC-367 (3/25) (CAMERA RGB PROCESS)
SCHEMATIC DIAGRAM ···························· 4-65
• VC-367 (4/25) (LENS DRIVE)
SCHEMATIC DIAGRAM ···························· 4-67
• VC-367 (5/25) (LENS DRIVE CONTROL)
SCHEMATIC DIAGRAM ···························· 4-69
• VC-367 (6/25) (CAMERA CONTROL)
SCHEMATIC DIAGRAM ···························· 4-71
• VC-367 (7/25) (BASE BAND PROCESS)
SCHEMATIC DIAGRAM ···························· 4-73
• VC-367 (8/25) (OSD, D3 FILTER)
SCHEMATIC DIAGRAM ···························· 4-75
• VC-367 (9/25) (HDV VIDEO ENCODER)
SCHEMATIC DIAGRAM ···························· 4-77
• VC-367 (10/25) (64MBIT SDRAM (L/U))
SCHEMATIC DIAGRAM ···························· 4-79
• VC-367 (11/25) (HDV SIGNAL/RF SIGNAL PROCESS)
SCHEMATIC DIAGRAM ···························· 4-81
• VC-367 (12/25) (HDV VIDEO DECODER)
SCHEMATIC DIAGRAM ···························· 4-83
• VC-367 (13/25) (64MBIT Y/C-SDRAM)
SCHEMATIC DIAGRAM ···························· 4-85
• VC-367 (14/25) (I LINK INTERFACE)
SCHEMATIC DIAGRAM ···························· 4-87
• VC-367 (15/25) (DV/RF SIGNAL PROCESS)
SCHEMATIC DIAGRAM ···························· 4-89
• VC-367 (16/25) (VIDEO A/D CONV.)
SCHEMATIC DIAGRAM ···························· 4-91
• VC-367 (17/25) (EVF RGB DRIVER, TIMING
GENERATOR)
SCHEMATIC DIAGRAM ···························· 4-93
• VC-367 (18/25) (HDV AUDIO SIGNAL PROCESS)
SCHEMATIC DIAGRAM ···························· 4-95
• VC-367 (19/25) (AUDIO INPUT SELECT, AUDIO
CONVERTOR)
SCHEMATIC DIAGRAM ···························· 4-97
• VC-367 (20/25) (DS CONTROL)
SCHEMATIC DIAGRAM ···························· 4-99
• VC-367 (21/25) (FRONT CONTROL)
SCHEMATIC DIAGRAM ·························· 4-101
• VC-367 (22/25) (LSI CONTROL)
SCHEMATIC DIAGRAM ·························· 4-103
• VC-367 (23/25) (MECHA CONTROL)
SCHEMATIC DIAGRAM ·························· 4-105
• VC-367 (24/25) (CONNECTOR-1)
SCHEMATIC DIAGRAM ·························· 4-107
• VC-367 (25/25) (CONNECTOR-2)
SCHEMATIC DIAGRAM ·························· 4-109
4-3.
PRINTED WIRING BOARDS ··································· 4-151
• CD-522 (R.G.B-CH CCD IMAGER, S/H, AGC)
PRINTED WIRING BOARD ····················· 4-151
• DA-033 (DC/DC CONVERTER)
PRINTED WIRING BOARD ····················· 4-155
• DB-018 (DC IN, CHARGE, DC/DC CONVERTER)
PRINTED WIRING BOARD ····················· 4-159
• VC-367 (CCD RF IN, R.G.B-CH AGC, A/D CONV.,
TIMING GENERATOR, CAMERA RGB PROCESS,
LENS DRIVE, LENS DRIVE CONTROL, CAMERA
CONTROL, BASE BAND PROCESS, OSD, D3 FILTER,
HDV VIDEO ENCODER, 64MBIT SDRAM (L/U),
HDV SIGNAL/RF SIGNAL PROCESS, HDV VIDEO
DECODER, 64MBIT Y/C-SDRAM, I LINK
INTERFACE, DV/RF SIGNAL PROCESS, VIDEO A/D
CONV., EVF RGB DRIVER, TIMING GENERATOR,
HDV AUDIO SIGNAL PROCESS, AUDIO INPUT
SELECT, AUDIO CONVERTOR, DS CONTROL,
FRONT CONTROL, LSI CONTROL, MECHA
CONTROL, CONNECTOR-1, CONNECTOR-2)
PRINTED WIRING BOARD ····················· 4-163
4-4.
WAVEFORMS ···························································· 4-169
4-5.
MOUNTED PARTS LOCATION ······························· 4-173
5.
REPAIR PARTS LIST
5-2.
ELECTRICAL PARTS LIST ········································ 5-31
Page of 77
Display

Sony HDR-FX1 / HDR-FX1E / Q002-HDR1 Service Manual ▷ Download

  • DOWNLOAD Sony HDR-FX1 / HDR-FX1E / Q002-HDR1 Service Manual ↓ Size: 9.35 MB | Pages: 77 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony HDR-FX1 / HDR-FX1E / Q002-HDR1 in PDF for free, which will help you to disassemble, recover, fix and repair Sony HDR-FX1 / HDR-FX1E / Q002-HDR1 Movie. Information contained in Sony HDR-FX1 / HDR-FX1E / Q002-HDR1 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.