Sony HDR-CX6EK / HDR-CX7 / HDR-CX7E / HDR-CX7EK / HDR-CX7K (serv.man2) Service Manual ▷ View online
1-2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-3-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
3
2
2
0
6
1
6
1
6
2
6
2
6
2
6
2
6
2
6
2
6
2
6
2
9
1
9
4
Detailed
Code
0
0
0
1
0
2
6
0
0
0
1
0
1
1
0
0
0
1
0
2
0
3
1
0
1
1
1
2
2
0
0
1
0
0
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Access error
Difficult to adjust forcus
(Cannot initialize focus)
(Cannot initialize focus)
EEPROM data are rewritten.
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Abnormality of IC for steadyshot.
IC for steadyshot and micro controller
communication abnormality among.
communication abnormality among.
Shift lens initializing failure.
Shift lens overheating (Pitch).
Shift lens overheating (Yaw).
Abnormality of thermistor.
Abnormality when flash is being charged.
Fault of writing to or erasing the
flashmemory
flashmemory
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
camcorder again.
camcorder again.
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin qh, qk of
CN5302 on the LD-222 board). If it is OK, check the focus
motor drive IC (IC5404 on the LD-222 board).
recover, check the focus MR sensor of lens block (pin qh, qk of
CN5302 on the LD-222 board). If it is OK, check the focus
motor drive IC (IC5404 on the LD-222 board).
Make EEPROM data correct value.
Inspect the lens block zoom MR sensor (pin w;, wa of CN5302
on the LD-222 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC5404 on the LD-222 board) when zooming is not performed.
on the LD-222 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC5404 on the LD-222 board) when zooming is not performed.
Check both C : 32 : 60 and E : 61 : 10 of the self-diagnosis code.
Inspect PITCH angular velocity sensors (SE7202 on the CM-077
board) peripheral circuits.
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE7201 on the CM-077
board) peripheral circuits.
board) peripheral circuits.
Refer to “1-4-1. E : 62 : 02 [Abnormality of IC for Steadyshot]
Occurred”.
Occurred”.
Inspect the steadyshot circuit (IC5703 on the LD-222 board).
Refer to “1-4-2. E : 62 : 10 [Shift Lens Initializing Failure]
Occurred”.
Occurred”.
Refer to “1-4-3. E : 62 : 11 [Shift Lens Overheating (Pitch)]
Occurred”.
Occurred”.
Refer to “1-4-4. E : 62 : 12 [Shift Lens Overheating (Yaw)]
Occurred”.
Occurred”.
Refer to “1-4-5. E : 62 : 20 [Abnormality of Thermistor]
Occurred”.
Occurred”.
Checking of flash unit or replacement of flash unit. (Note 1)
Inspect the flash memory (IC2201 on the VC-493 board).
(Note 2)
(Note 2)
Note 1: After repair, be sure to perform “1-5. PROCESS AFTER FIXING FLASH ERROR”.
Note 2: Refer to Service Manual, ADJ (“1-3. DESTINATION DATA WRITE”).
Note 2: Refer to Service Manual, ADJ (“1-3. DESTINATION DATA WRITE”).
1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-4. METHOD OF COPING WITH SHIFT LENS ERROR
about 330 msec
Fig. 3
Measurement points on the VC-493 board
Fig. 2
Change in output voltage of R5792 on the LD-222 board
Note: The length of low section will vary a little depending on the
conditions.
Fig. 1
Measurement points on the LD-222 board
R5792
IC5703
R5721
R5737
LD-222 BOARD (SIDE A)
IC1803
R1846
VC-493 BOARD (SIDE A)
1-4
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-4-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-222 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1803 of VC-493 board) periphery.
the camera control circuit (IC1803 of VC-493 board) periphery.
Note: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld
operation.
operation.
1-4-2. E : 62 : 10 [Shift Lens Initializing Failure] Occurred
Inspection method:
1)
1)
Perform the “Check 1” of “Shift Lens Check” (Note 1).
Note 1: For “Shift Lens Check”, refer to Service Manual, ADJ (“7. Shift Lens Check” of “3-2. SERVICE MODE”).
Note 1: For “Shift Lens Check”, refer to Service Manual, ADJ (“7. Shift Lens Check” of “3-2. SERVICE MODE”).
2)
If “EEPROM Error” is displayed while executing the “Check 1”, inspect the EEPROM (IC1804 of VC-493 board).
3)
Turn the power OFF and ON again.
4)
Check that no error occurs. If an error occurs, replace the lens block (Note 2).
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the hand-
held operation.
held operation.
1-4-3. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Inspection method:
1)
1)
Perform the “Check 2” of “Shift Lens Check” (Note 1).
Note 1: For “Shift Lens Check”, refer to Service Manual, ADJ (“7. Shift Lens Check” of “3-2. SERVICE MODE”).
Note 1: For “Shift Lens Check”, refer to Service Manual, ADJ (“7. Shift Lens Check” of “3-2. SERVICE MODE”).
2)
Check if the shift lens moves while executing the “Check 2”. If the shift lens does not move, replace the lens block (Note 2). When the
shift lens moved, proceed to the order 3.
shift lens moved, proceed to the order 3.
3)
While executing the “Check 2”, measure with an oscilloscope the output voltage of R5721 in the periphery of IC5703 on the LD-222
board to check the output voltage varies.
board to check the output voltage varies.
4)
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage varied, proceed to the order 5.
5)
Turn the power OFF.
6)
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-222 board, turn the power ON
to check that the output voltage immediately after the power on change as shown in Fig. 2.
to check that the output voltage immediately after the power on change as shown in Fig. 2.
7)
If the output voltage changes as shown in Fig. 2, replace the lens block (Note 2). If it does not change as shown in Fig. 2, inspect the
camera control circuit (IC1803 of VC-493 board) periphery.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
camera control circuit (IC1803 of VC-493 board) periphery.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the hand-
held operation.
held operation.
1-4-4. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Inspection method:
1)
1)
Perform the “Check 3” of “Shift Lens Check” (Note 1).
Note 1: For “Shift Lens Check”, refer to Service Manual, ADJ (“7. Shift Lens Check” of “3-2. SERVICE MODE”).
Note 1: For “Shift Lens Check”, refer to Service Manual, ADJ (“7. Shift Lens Check” of “3-2. SERVICE MODE”).
2)
Check if the shift lens moves while executing the “Check 3”. If the shift lens does not move, replace the lens block (Note 2). When the
shift lens moved, proceed to the order 3.
shift lens moved, proceed to the order 3.
3)
While executing the “Check 3”, measure with an oscilloscope the output voltage of R5737 in the periphery of IC5703 on the LD-222
board to check the output voltage varies.
board to check the output voltage varies.
4)
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage varied, proceed to the order 5.
5)
Turn the power OFF.
6)
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-222 board, turn the power ON
to check that the output voltage immediately after the power on change as shown in Fig. 2.
to check that the output voltage immediately after the power on change as shown in Fig. 2.
7)
If the output voltage changes as shown in Fig. 2, replace the lens block (Note 2). If it does not change as shown in Fig. 2, inspect the
camera control circuit (IC1803 of VC-493 board) periphery.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
camera control circuit (IC1803 of VC-493 board) periphery.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the hand-
held operation.
held operation.
1-5
ENGLISH
JAPANESE
ENGLISH
JAPANESE
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-5. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by execution of “Clear All record-data”.
Note: For “Clear All record-data”, refer to Service Manual, ADJ (“6. Record Data” of “3-2. SERVICE MODE”).
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by execution of “Clear All record-data”.
Note: For “Clear All record-data”, refer to Service Manual, ADJ (“6. Record Data” of “3-2. SERVICE MODE”).
1-4-5. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Check that R1846 in the periphery of IC1803 on the VC-493 board is 0
Ω and energizes. If it is not energizes, replace the R1846.
When R1846 is 0
Ω and energizes, replace the lens block (Note).
3
Check that no error occurs, after replacing the lens block and performing the necessary adjustment. If an error occurs, inspect
the camera control circuit (IC1803 of VC-493 board) periphery.
the camera control circuit (IC1803 of VC-493 board) periphery.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld
operation.
operation.
Click on the first or last page to see other HDR-CX6EK / HDR-CX7 / HDR-CX7E / HDR-CX7EK / HDR-CX7K (serv.man2) service manuals if exist.