Sony HDR-CX220 / HDR-CX220E / HDR-CX230 / HDR-CX230E / HDR-CX280 / HDR-CX280E / HDR-CX290 / HDR-CX290E / HDR-CX320 / HDR-CX320E / HDR-CX380 / HDR-CX380E / HDR-CX390 / HDR-CX390E / HDR-PJ220 / HDR-PJ220E / HDR-PJ230 / HDR-PJ230E / HDR-PJ320E / HDR-PJ380 / HDR-P Service Manual ▷ View online
1-5
HDR-CX220/CX220E/CX230/CX230E/CX280/CX280E/CX290/CX290E/CX320/CX320E/CX380/CX380E/CX390/CX390E/PJ220/PJ220E/PJ230/PJ230E/PJ320E/PJ380/PJ380E/PJ390/PJ390E_L2
– ENGLISH –
approx. 330 msec
Note: The length of low section will vary a little depending on the conditions.
Fig. 2
Change in output voltage of R5505 on the VC-1010 board
1-5-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5505 in the periphery of IC5501 on the VC-1010 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1301 of VC-1010 board) periphery.
the camera control circuit (IC1301 of VC-1010 board) periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Order
AdjustBlock
AdjustCode
Procedure
1
Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the
[SERVICE] tab.
[SERVICE] tab.
2
Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
3
While setting the order 1, measure with an oscilloscope the output voltage of C5513 and C5514 in
the periphery of IC5501 on the VC-1010 board to check the output voltage varies.
the periphery of IC5501 on the VC-1010 board to check the output voltage varies.
4
If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.
When the output voltage varied, proceed to the order 5.
5
Turn the power OFF.
6
While measuring with an oscilloscope the output voltage of R5505 in the periphery of IC5501 on the
VC-1010 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
VC-1010 board, turn the power ON to check that the output voltage immediately after the power on
change as shown in Fig. 2.
7
If the output voltage rises to 3V, replace the lens block (Note).
If it does not rises to 3V, inspect the camera control circuit (IC1301 and IC5501 of VC-1010 board)
periphery.
If it does not rises to 3V, inspect the camera control circuit (IC1301 and IC5501 of VC-1010 board)
periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5-3.E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Order
AdjustBlock
AdjustCode
Procedure
1
Start the Adjust Manual in the Adjust Station and execute the [Measure to E:62:11/12] on the [SER-
VICE] tab.
VICE] tab.
2
Check if the shift lens moves while setting the order 1.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
If the shift lens does not move, replace the lens block (Note).
When the shift lens moved, proceed to the order 3.
3
While setting the order 1, measure with an oscilloscope the output voltage of C5515 and C5516 in
the periphery of IC5501 on the VC-1010 board to check the output voltage varies.
the periphery of IC5501 on the VC-1010 board to check the output voltage varies.
4
If the output voltage does not vary, replace the lens block (Note).
When the output voltage varied, proceed to the order 5.
When the output voltage varied, proceed to the order 5.
5
Turn the power OFF.
6
While measuring with an oscilloscope the output voltage of R5505 in the periphery
of IC5501 on the VC-1010 board, turn the power ON to check that the output voltage
immediately after the power on change as shown in Fig. 2.
of IC5501 on the VC-1010 board, turn the power ON to check that the output voltage
immediately after the power on change as shown in Fig. 2.
7
If the output voltage rises to 3V, replace the lens block (Note).
If it does not rises to 3V, inspect the camera control circuit (IC1301 and IC5501 of VC-1010 board)
periphery.
If it does not rises to 3V, inspect the camera control circuit (IC1301 and IC5501 of VC-1010 board)
periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Confirm the connections of flexible flat cables and connectors between the lens block and VC-1010 board.
3
In case of no malfunction of connections, replace the lens block with new one (Note) . When the error has occurred in spite of the lens
replacement, replace VC-1010 board with new one.
replacement, replace VC-1010 board with new one.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-6
HDR-CX220/CX220E/CX230/CX230E/CX280/CX280E/CX290/CX290E/CX320/CX320E/CX380/CX380E/CX390/CX390E/PJ220/PJ220E/PJ230/PJ230E/PJ320E/PJ380/PJ380E/PJ390/PJ390E_L2
– ENGLISH –
1-6. NOTE ON REPLACING PROJECTOR UNIT
(PJ220/PJ220E/PJ230/PJ230E/PJ320E/PJ380/PJ380E/PJ390/PJ390E)
Refer to the following flowchart when repairing or inspecting the projector’s projection function.
If you have received an indication on the projector’s projection function from the customer, check defective part according to the following flow-
chart.
When a defective part has been clarified, repair the projector according to the check result.
chart.
When a defective part has been clarified, repair the projector according to the check result.
Note 1: The projector unit (copper plate in particular) becomes hot after it is used.
When replacing a part of the projector unit, wait until it is cooled down.
Note 2: Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth.
Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water.
Never use a solvent such as alcohol, benzene or thinner; acid, alkaline or abrasive detergent; or a chemical cleaning cloth, as they will damage the lens sur-
face.
face.
Projector problem checking procedure (other than indication on brightness)
Indicated defective
projector received
Measure brightness.
( 2)
Yes
No
OK
OK
NG
NG
OK
NG
A
B
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
Inspect projector
LED.
( 1)
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40
Enter the number on the label attached to the unit.
Serial number input
LD40
Syywwnnnnn
Enter the red part.
Projector problem checking procedure (indication on brightness)
Yes
No
OK
NG
OK
NG
OK
NG
A
B
Indicated defective
projector received
Measure brightness.
( 2)
Measure brightness.
( 2)
Indication on
brightness
Inspect projector
LED.
( 1)
1 Refer to the ADJUST tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
2 Refer to the SERVICE tab of Adjust Manual.
END
-
-
-
-
-
-
-
Replace projector unit (light emitting block). (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Replace PJ board. (*1)
Replace both projector unit (light emitting block)
and PJ board. (*1)
Projector Data Input
Fixed value input
Enter the number on the label attached to the unit.
Serial number input
LD40
Enter the number on the label attached to the unit.
Serial number input
LD40
Syywwnnnnn
Enter the red part.
1-7
HDR-CX220/CX220E/CX230/CX230E/CX280/CX280E/CX290/CX290E/CX320/CX320E/CX380/CX380E/CX390/CX390E/PJ220/PJ220E/PJ230/PJ230E/PJ320E/PJ380/PJ380E/PJ390/PJ390E_L2
1-1. 修理時の電源供給について
本機では,安定化電源(8.4Vdc)からバッテリ端子に電源を供給した場合,約10秒後にシャットオフし,動作しなくなります。
これを避けるため,下記の方法を用いてください。
これを避けるため,下記の方法を用いてください。
方法:
ACアダプタを使用する。
1-2. VC-1010基板交換時の注意
基板交換時は,下記の点に注意してください。
仕向けデータ
補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を実行させてください。
補修用基板交換後,電源を入れると内蔵記録メディアエラーが表示される場合がありますが,「DESTINATION DATA WRITE」を実行
させると消えます。「DESTINATION DATA WRITE」実行しても消えない場合は,内蔵記録メディアをフォーマットしてください。
Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を実行させてください。
補修用基板交換後,電源を入れると内蔵記録メディアエラーが表示される場合がありますが,「DESTINATION DATA WRITE」を実行
させると消えます。「DESTINATION DATA WRITE」実行しても消えない場合は,内蔵記録メディアをフォーマットしてください。
USBシリアルセーブ
補修用基板と交換する時,交換前の基板よりUSBシリアルNo.を取得してください。
データの取得はAdjust StationからAdjust Manualを起動させて「USB SERIAL SAVE」を実行させてください。
データの取得はAdjust StationからAdjust Manualを起動させて「USB SERIAL SAVE」を実行させてください。
USBシリアルNo.およびプロダクトIDについて
本機はセット固有のID(USBシリアルNo.)と機種固有のID(プロダクトID)を書き込んだ後に出荷されています。
新品の補修用基板にはこれらのIDが書き込まれていないため,基板交換後にIDを入力する必要があります。
補修用基板に交換した後はAdjust StationからAdjust Manualを起動し,「PRODUCT ID & USB SERIAL No. INPUT」を実行させてIDを入
力してください。
新品の補修用基板にはこれらのIDが書き込まれていないため,基板交換後にIDを入力する必要があります。
補修用基板に交換した後はAdjust StationからAdjust Manualを起動し,「PRODUCT ID & USB SERIAL No. INPUT」を実行させてIDを入
力してください。
Note: 新しくプロダクトIDを入力すると,必ずしも基板交換前のIDと同じIDになるとは限りません。新しいIDと元のIDが違う場合にはお客様がユーザー登録さ
れているIDと相違が出てしまう可能性があります。
プロジェクター用のデータ (Projector Model)
補修用基板と交換する時,交換前の基板より下記のデータを取得してください。
・ Fixed value(プロジェクターの照射性能を示す値)。
・ Serial number(プロジェクターユニットの製造シリアル番号)。
・ Serial number(プロジェクターユニットの製造シリアル番号)。
データの取得はAdjust StationからAdjustManualを起動させて,[DATA]タブにある[Projector Data Reference]を参照してください。
内蔵メモリー搭載機について (IM Model)
補修用基板に交換後は,最初に下記の手順を実行してください。
1. Adjust ManualのADJUSTタブにある,「DESTINATION DATA WRITE」を実行する。
2. 下記のスクリプトファイルを実行する。
1. Adjust ManualのADJUSTタブにある,「DESTINATION DATA WRITE」を実行する。
2. 下記のスクリプトファイルを実行する。
・ 13DdmMmcReadTestMINI_v5.vbe
・ 13DdmMmcMakePartition_v5.vbe
Note: スクリプトファイルはTISSホームページより入手してください。
TISSホームページで検索する際はPart Number欄に
「IM_VC_TOOL」
と入力して検索してください。
このスクリプトファイルを実行しなかった場合,以下のような症状が発生する可能性があります。
必ず上記のスクリプトを実行してください。
必ず上記のスクリプトを実行してください。
・ 内蔵メモリーがメディアとして認識できない
・ 内蔵メモリー内に保存されている,管理ファイルの修復ができない
・ 内蔵メモリーのフォーマットができない
・ 内蔵メモリー内に保存されている,管理ファイルの修復ができない
・ 内蔵メモリーのフォーマットができない
– JAPANESE –
START
END
セットが自動的に再起動される
USB
接続を解除し, 電源を切る
“USB接続”を選択し,
USB
接続を行う
“13DdmMmcReadTestMINI_v5.vbe”
を実行
(数秒後)
“SetOverallReadMINI OK”表示
(約10秒後)
セットが自動的に再起動される
“13DdmMMCMakePartition_v5.vbe”
を実行
(数秒後)
“MakePartition OK”表示
電源を入れたまま,
AC
アダプタを抜き挿しする
処理は自動で実行される
(Blue画面)
セットをPCにUSB接続し, 電源を入れる
* PC
はSeusEX がインストール済で,
SeusEX
への接続が可能であること
Fig.1
1-8
HDR-CX220/CX220E/CX230/CX230E/CX280/CX280E/CX290/CX290E/CX320/CX320E/CX380/CX380E/CX390/CX390E/PJ220/PJ220E/PJ230/PJ230E/PJ320E/PJ380/PJ380E/PJ390/PJ390E_L2
– JAPANESE –
1-3. Destination Data ファイルの追加について
Adjust manual に含まれる Destination Data ファイルが古い場合,
「DESTINATION DATA WRITE」 が実行できないことがあります。
その場合は,下記の手順を参考にして, TISS ホームページより新しい Destination Data ファイル を入手してください。
Note 1: この機種で仕向け設定を行うには,DSC-WX50シリーズの Adjust manual がインストールされている必要があります。
先に DSC-WX50 シリーズの Adjust manual をインストールしてください。
Note 2: 手順中の画像は実際と異なる場合があります。
1) 使用している Adjust manual の Destination Data ファイルが古い場合, Fig. 1 のようなウインドウが表示される。
[OK] ボタンをクリックする。
Fig.
1
2) Destination Data Write ウインドウが表示される。
Adjust manual の保持している Destination Data ファイル のバージョンを確認する。
Destination Ver. ウインドウ
3) TISSホームページにて,新しい Destination Data ファイルを入手したい機種を検索する。
Destination Data ファイルが更新されている場合,「Destination File For 機種名 .zip」 という名称のファイルが登録されてい
る。
る。
(例) Destination File For DSC-WX50.zip
また,Remarks欄にはこの Destination Data ファイルが対応するバージョンが記載されています。
Note: バージョンが更新されていなかった場合は,サービスヘッドクォーターへお問い合わせください。
4) 該当機種の Destination Data ファイルをダウンロードし,解凍する。
5) Adjust manual の Adjust タブにある,「DESTINATION DATA WRITE」 を実行する。
[START] ボタンをクリックする。
Click on the first or last page to see other HDR-CX220 / HDR-CX220E / HDR-CX230 / HDR-CX230E / HDR-CX280 / HDR-CX280E / HDR-CX290 / HDR-CX290E / HDR-CX320 / HDR-CX320E / HDR-CX380 / HDR-CX380E / HDR-CX390 / HDR-CX390E / HDR-PJ220 / HDR-PJ220E / HDR-PJ230 / HDR-PJ230E / HDR-PJ320E / HDR-PJ380 / HDR-P service manuals if exist.