DOWNLOAD Sony DCR-TRV75 / DCR-TRV75E / DCR-TRV80 / DCR-TRV80E (serv.man4) Service Manual ↓ Size: 1.34 MB | Pages: 70 in PDF or view online for FREE

6-46

Use the following measuring instruments for video section
adjustments.

1)

TV monitor

2)

Oscilloscope (dual-phenomenon, band width above 30 MHz
with delay mode) (Unless specified otherwise, use a 10 : 1
probe.)

3)

Frequency counter

4)

Pattern generator with video output terminal

5)

Digital voltmeter

6)

Audio generator

7)

Audio level meter

8)

Audio distortion meter

9)

Audio attenuator

10) Regulated power supply
11) Alignment tapes

• Tracking standard (XH2-1)

Parts code: 8-967-997-01

• SW/OL standard (XH2-3)

Parts code: 8-967-997-11

• Audio operation check for NTSC (XH5-3)

Parts code: 8-967-997-51

• System operation check for NTSC (XH5-5)

Parts code: 8-967-997-61

• Audio operation check for PAL (XH5-3P)

Parts code: 8-967-997-55

• System operation check for PAL (XH5-5P)

Parts code: 8-967-997-66

12) Adjustment remote commander (J-6082-053-B)
13) CPC-7 jig (J-6082-382-A)
14) Extension cable (100P 0.5mm) (J-6082-352-A)

For extension between the DI-089 board (CN4004) and the
VC-316 board (CN1003)

6-47

Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.

1)

The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to “VCR” (or
“PLAYER”) or set the “Forced VTR Power ON mode” using
the adjustment remote commander (Note2).
To set to the Camera mode, set the power switch to “CAMERA”
or set the “Forced Camera Power ON mode” using the
adjustment remote commander (Note3).
After completing adjustments, be sure to exit the “Forced VTR
Power ON Mode” or “Forced Camera Power ON Mode”.
(Note5)

2)

The front panel block (Microphone unit, MA-424 board, FP-
633 flexible (MF sensor)) must be assembled for connecting
the adjustment remote commander. To remove it, disconnect
the following connector.

MA-424 board CN5903 (30P, 0.5mm)

3)

Cabinet (R) (CK-132board, LCD block) need not be connected.
But removing the cabinet (R) (removing the VC-316 board
CN1007) means removing the lithium 3V power supply (CK-
132 board, BT5201), data such as date, time, user-set menus
will be lost. After completing adjustments, reset these data.
But, the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the cabinet (R) has
been removed. (Refer to “6-4.Service Mode” for the data on
the history use and the self-diagnosis data.)
To remove the cabinet (R), disconnect the following connector.

VC-316 board CN1007 (51P, 0.3mm)

4)

The EVF block (LB-088 board) is need not be connected. To
remove it, disconnect the following connector.

DI-089 board CN3201 (20P, 0.5mm)

5)

The intelligent accessory shoe is need not be connected. To
remove it, disconnect the following connector.

DI-089 board CN4001 (10P, 0.5mm)

6)

The flash unit is need not be connected. To remove it, disconnect
the following connector.

DI-089 board CN4005 (33P, 0.3mm)

7)

To open the DI-089 board, use the following extension cable
between the DI-089 board CN4004 and VC-316 board CN1003.

J-6082-352-A (100P, 0.5mm)

8)

The CD-437 board of the lens block is must be connected,
because the timing generator (IC7501) is provided on the board.

9)

By setting the “Forced VTR Power ON mode”, the video section
can be operate even if the control switch block (PS-2890) has
been removed. When removing the control switch blocks (PS-
2890 and FK-4200) and the memory stick connector, disconnect
the following connector.

VC-316 board CN1006 (27P, 0.3mm)

Setting the “Forced VTR Power ON” mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE

button of the adjustment remote commander.
The above procedure will enable the VTR power to be turned
on with the control switch block (PS-2890 block) removed.
After completing adjustments, be sure to exit the “Forced Power
ON mode”.

Setting the “Forced Camera Power ON” mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE

button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (PS-2890 block) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".

Setting the “Forced Memory Power ON” mode (Memory mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press the PAUSE

button of the adjustment remote commander.
The above procedure will enable the memory power to be turned
on with the control switch block (PS-2890 block) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".

Exiting the “Forced Power ON” mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE

button of the adjustment remote commander.

3) Select page: 0, address: 01, and set data: 00.

6-48

The measuring point of the playback RF signal is CN1004 of VC-
315 board. Connect the measuring instruments via the CPC-7 jig
(J-6082-382-A). Refer to “MECHANISM SECTION ADJUST-
MENT” for the measuring method. The following table lists the pin
numbers and signal names of CN1004.

Table 6-3-1.

Connect the measuring instruments as shown in Fig. 6-3-2, and
perform the adjustments.

1

2

3

4

5

6

7

8

FRRV

RF MON

RF IN/LANC
JACK IN

SWP

PANEL COM

REG_GND

H START

REG_GND

9

10

11

12

13

14

15

16

PANEL VG

REG_GND

EVF VCO

REG_GND

EVF VG

EXT DA

N.C.

N.C.

Fig. 6-3-2.

CN1004

16

1

Remove the 
CPC lid.

Fig. 6-3-1.

6-49

Use the alignment tapes shown in the following table.
Use tapes specified in the signal column of each adjustment.

Fig. 6-3-3 shows the 75% color bar signals recorded on the alignment
tape for Audio Operation Check.

Measure with video terminal (Terminated at 75 

Ω

)

Tape path adjustment

Switching position adjustment

Audio system adjustment

Operation check

Tracking standard (XH2-1)

SW/OL standard (XH2-3)

Audio operation check
(XH5-3 (NTSC), XH5-3P (PAL))

System operation check
(XH5-5 (NTSC), XH5-5P (PAL))

Color bar signal waveform

Color bar pattern

Color bar signal waveform

Color bar pattern

Fig. 6-3-3. Color bar signal of alignment tapes

Video input/output

Special stereo mini jack
Video signal:

1 Vp-p, 75 

Ω

 unbalanced,

sync negative

S video input/output

4-pin mini DIN
Luminance signal:

1 Vp-p, 75 

Ω

 unbalanced,

sync negative

Chrominance signal: 0.286 Vp-p, 75 

Ω

 unbalanced (NTSC)

: 0.300 Vp-p, 75 

Ω

 unbalanced (PAL)

Audio input/output

Special stereo mini jack
Input level: 327mV
Input impedance: More than 47k

Ω

Output level: 327 mV (at load impedance 47 k

Ω

)

Output impedance: Below 2.2 k

Ω