DOWNLOAD Sony DCR-TRV75 / DCR-TRV75E / DCR-TRV80 / DCR-TRV80E (serv.man2) Service Manual ↓ Size: 10.4 MB | Pages: 103 in PDF or view online for FREE

2-11

1

 Screw

     (M1.7 

×

 4),

     lock ace, p2

3

 BT panel assembly

4

 Battery terminal board

2

 Strap bracket

     (lower) 

A

2

 

Two screws

     (M1.7 

× 

2.5), 

     lock ace, p2

1

 Slide the EVF 

     in the direction of the arrow 

A

.

Be careful because the 

6

 FP-637 flexible board 

may be damaged if it is removed forcibly from the 

5

 External connector (hot shoe) .

6

 

FP-637 flexible board

    (10P)

3

 

Two dowels

4

 Two claws

5

 Remove the external connector

     (hot shoe) and shoe base 
     in the direction of the arrow 

B

.

B

Shoe base

2-12

BT-
012

VC-316

VC-316

VC-316

BT

-012

3

 

BT frame

7

 

BT sheet insulating

     (TRV80/TRV80E)

5

 

FP-457 Flexible board (15P)

     (TRV80/TRV80E)

FP-457 Flexible board 
(TRV80/TRV80E)

4

 

Screw (M1.7 

× 

2.5)

     (TRV80/TRV80E)

1

 

Screw (M1.7 

× 

2.5)

8

 

BT-012 board

     (TRV80/TRV80E)

BT-012 board
(TRV80/TRV80E)

6

 

BA-001 Harness

     (TRV80/TRV80E)

2

 

Two dowels

Route the Antenna cord underneath 
the FP-634 Flexible board.

2-13

VC-
316

DI-
089

3

 DI heat sink

     assembly

7

 Two tapping screws

     (M1.7 

×

 5)

4

 Peel off the tape.

6

 Slide the EVF slightly

     in the direction of the
     arrow so that the two
     screws 

7

 become 

     visible.

5

 FP-435 flexible board (20P)

8

 EVF section

Tape (A)

2

 

Two dowels

1

 

Two dowels

FP-435 flexible board

Routing of the FP-435 flexible board

2-14

A

2

 

Two tapping screws

     (M1.7 

× 

5)

3

 VF base assembly

qf

 VF lens assembly

qs

 

LB-088 board, 

     Lamp guide

8

 

FP-435 Flexible 

     board (20P)

0

 

LCX033AN-J (16P)

qj

 

LB-088 board

qh

 Lamp guide

qa

 

Three claws

qd

 

Four claws

9

 

Ferrite core

7

 

VF electrostatic 

     sheet

5

 

Tape (A)

4

Two claws

qg

 Two claws

1

 Raise the EVF in the 

     direction of the arrow 

A

.

Prism sheet

Illuminator

LCX033AN-J

LCD Cushion

When separating the 

qs

 LB-088 board and 

Lamp guide from the 

qf

 VF lens assembly 

by removing the three 

qa

 claws, do not face 

the side of the VF lens assembly on which 
the LB-088 board is installed, downwards. 
Because the Illuminator and others may fall 
out of the VF lens assembly, hold the 
illuminator and others using tape or paper 
as shown to prevent them from falling. 
Be careful on this point especially when 
removing the LB-088 board and Lamp guide 
because the three claws located in the VF 
lens assembly are easy to break.

Hold the illuminator 
and others using 
tape or paper as 
shown to prevent 
them from falling.

Tape (A)

FP-435 
flexible 
board

Flexible 
electrostatic 
sheet 

6

 

Flexible 

     electrostatic 
     sheet 

 

Reinforcement board

Insert the ferrite core in place.

Align it with 

flexible electrostatic sheet 

 

and attach. 

Tape (A)

Ferrite core

Reinforcement 
board