Sony DCR-TRV5 / DCR-TRV5E Service Manual ▷ View online
2-4
2-6. REMOVAL OF CD-193 BOARD
2
M1.7
×
2
3
M1.7
×
2
5
CD-193 board
4
BTP2
×
7
1
CD-193 board from CN302
6
Remove soldering
9
Remove soldering
7
Two screw
+P type2 LOCKACE M1.7
×
2
8
Zoom motor
!º
Two screw
+P type2 LOCKACE M1.7
×
2
!¡
Focus motor
Zoom lens (VCL- 4010VD)
2-5
a
a
Board
PD-100
2
Press the claw
3
Pull
1
Cushion
5
FP-699 flexible board
PANEL CLOSE switch (S002) block
6
M2
×
2.5
@º
M1.7
×
2.5
#¢
Lithium battery
lid
#§
Harness SP-155
#∞
Insert a tweezers tip
or the like and snap
it out
it out
8
Turn the LCD block in
the direction of the arrow
!¡
Hinge cover (front)
!¡
Hinge cover (rear)
!º
Claws
!∞
Claws
@¡
Claws
#º
Claws
!£
FP-699 flexible board
7
Turn the tilt base
in the direction
of the arrow
of the arrow
!§
Remove the LCD cabinet (R) assembly
in the direction of the arrow while taking
care not to damage the harness (SP-154)
care not to damage the harness (SP-154)
!§
LCD cabinet (R)
assembly
@™
LCD cabinet (L)
#¡
LCD frame
@¢
ND901
@£
LCD901
@•
Hinge assembly
*
1
@§
Harness SP-152
(from CN5802)
@∞
Harness blind tape
!•
PD flexible
sheet
#™
PD-100 board
!ª
From CN5501
!ª
From CN5804
!ª
From CN5701
Remove the flexible board
connected to the LCD,
from the cabinet (R) assembly
connected to the LCD,
from the cabinet (R) assembly
Harness
4
M1.7
×
2
6
M2
×
2.5
#£
2
×
5
#¶
LI-65 board
9
M1.7
×
2
9
M1.7
×
2
!™
M1.7
×
2
@ª
M1.7
×
2
@¶
M1.7
×
2
!¢
M1.7
×
2
@§
Harness SP-153
(from CN5801)
!¶
Harness SP-154
(from CN5803)
Hinge cover (lower)
(3-989-856-01)
(3-989-856-01)
Melt them by soldering iron or
attach them with adhesive agent
attach them with adhesive agent
Hinge assembly
(X-3948-660-1)
(X-3948-660-1)
*
1 When replacing the hinge assembly, replace the hinge cover (lower)
and sleeve harness at the same time because the hinge assembly
does not include the hinge cover (lower) and sleeve harness.
does not include the hinge cover (lower) and sleeve harness.
Speaker
Speaker
LCD lock spring
Open button
Control switch block (VL4680)
Cushion (VL)
Sleeve harness
(3-051-046-01)
(3-051-046-01)
Attach sleeve harness to
hinge assembly by
adhesive agent.
hinge assembly by
adhesive agent.
2-7. REMOVAL OF LCD BLOCK
2-6
2-8. SERVICE POSITION
(ADJUSTMENT, CHECK, OR/AND VOLTAGE MEASUREMENT MAINLY)
Procedure : Remove the following parts as shown referring to sections 2-1 to 2-7, and connect them as shown below.
DD-110 board
MD
FK/PS block
Work table
MA-330 board
VC-207 board
Blocks
Use appropriate boxes or the like to support
the VC-207 board, lens block, LCD block,
FK/PS block and MA-330 board.
Use appropriate boxes or the like to support
the VC-207 board, lens block, LCD block,
FK/PS block and MA-330 board.
Work table
Lens block
LCD block
CPC-8 jig
(J-6082-388-A)
(J-6082-388-A)
LI-65 board
Extension cable
(J-6082-395-A)
(J-6082-395-A)
2-7E
2-9. CIRCUIT BOARDS LOCATION
FP-694
(FUNCTION KEY)
(FUNCTION KEY)
PS4680
(POWER SW)
(POWER SW)
FP-691
(A/V OUT JACK)
(A/V OUT JACK)
LI-65
(BATTERY)
(BATTERY)
FP-695
(LED)
(LED)
MA-330
(AUDIO PROCESSOR & IR TRANSMITTER)
(AUDIO PROCESSOR & IR TRANSMITTER)
PD-100
RGB DECODER,
TIMMING GENERATOR,
BACK LIGHT GENERATOR
RGB DECODER,
TIMMING GENERATOR,
BACK LIGHT GENERATOR
FK4680
(USER CONTROL)
(USER CONTROL)
VL4680
(VOLUME)
(VOLUME)
FP-699
(FUNCTION KEY)
(FUNCTION KEY)
VC-207
CAMERA PROCESS, FOCUS/ZOOM/IRIS DRIVE, VIDEO OUT, REC/PB PROCESS,
RF INTERFACE, RGB DECODER, BLOCKING, ECC. TBC. CHCD, DV SIGNAL PROCESS,
AUDIO PROCESS, MODE CONTROL, EVR/AUDIO, MECHA CON/SERVO
CAMERA PROCESS, FOCUS/ZOOM/IRIS DRIVE, VIDEO OUT, REC/PB PROCESS,
RF INTERFACE, RGB DECODER, BLOCKING, ECC. TBC. CHCD, DV SIGNAL PROCESS,
AUDIO PROCESS, MODE CONTROL, EVR/AUDIO, MECHA CON/SERVO
DD-110
(DRUM/CAPSTAN PWM DRIVE)
(DRUM/CAPSTAN PWM DRIVE)
AU-204
(AUDIO PROCESSOR)
(AUDIO PROCESSOR)
CD-193
(CCD IMAGER)
(CCD IMAGER)
VF-124
(COLOR EVF)
(COLOR EVF)
Click on the first or last page to see other DCR-TRV5 / DCR-TRV5E service manuals if exist.