Sony DCR-TRV30E Service Manual ▷ View online
— 17 —
2-9.
FLASH UNIT
A
A
1
Two tapping
screws
(M1.7
(M1.7
×
3.5)
2
FP-330 flexible board (23P)
qa
Two claws
0
Two dowels
qs
ST cabinet (lower)
9
ST cabinet (upper)
(Note)
qf
Flash unit
qd
ST hinge assembly
4
Screw
(M1.7
×
2.5), p
3
Plunger solenoid (6P)
6
Plunger solenoid
5
Bolt screw (M1.4)
8
Two claws
7
Two tapping
screws
(M1.7
(M1.7
×
5)
Xenon tube
Note:
The power supply capacitor of the flash unit is charged to the high tension voltage as high as 300 V at a maximum. You will get
electrical shock when you touch the terminal of the charged capacitor. The charged potential remains even after the main power
of the machine is turned off. Discharge the remaining power in the capacitor referring to Service Note (page 6).
of the machine is turned off. Discharge the remaining power in the capacitor referring to Service Note (page 6).
Caution: High voltage
Caution: High voltage
Flash unit
Power supply
capacitor
2-10. PO-006 BOARD, HINGE ASSEMBLY
1
Two screws
(M1.7
×
4),
lock ace, p2
3
Two screws
(M1.7
×
2.5),
lock ace, p2
6
Screw
(M1.7
×
2.5),
lock ace, p2
1
Screw
(M1.7
×
2.5), p
2
q;
Screw
(M1.7
×
2.5), p
5
Hinge cover (front)
7
Hinge cover (rear)
2
PO-006 board
8
Harness
(PC-118) (12P)
9
Harness
(PC-119) (14P)
qa
FP-181 flexible board
qs
Hinge assembly
4
Two claws
Remove the LCD unit referring to section “2-1. DISASSEMBLY” of Level 2 before starting the following disassembling
work.
work.
— 18 —
2-11. GRIP BELT
9
Grip belt
2
Two tapping
screws (M1.7
×
5)
5
Tapping
screw (M1.7
×
3.5)
7
Screw
(M2
×
4)
3
Three tapping
screws (M1.7
×
3.5)
1
Open the
cassette lid
4
Grip cover
6
Control switch block
(PS-1800)
8
Claw
Flash unit
Caution: High voltage
PRECAUTION DURING
INSTALLATION
INSTALLATION
To attach, align the switch
position as shown.
position as shown.
Power supply
capacitor
Note:
The power supply capacitor of the flash unit is charged to the high tension voltage as high as 300 V at a maximum. You will get
electrical shock when you touch the terminal of the charged capacitor. The charged potential remains even after the main power
of the machine is turned off. Discharge the remaining power in the capacitor referring to Service Note (page 6).
of the machine is turned off. Discharge the remaining power in the capacitor referring to Service Note (page 6).
— 19 —
3.
REPAIR PARTS LIST
3-1.
EXPLODED VIEWS
NOTE:
•
-XX, -X mean standardized parts, so they may
have some differences from the original one.
have some differences from the original one.
•
Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
The mechanical parts with no reference number
in the exploded views are not supplied.
in the exploded views are not supplied.
3-1-1.
OVERALL SECTION
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
The components identified by mark
0
or
dotted line with mark
0
are critical for safety.
Replace only with part number specified.
1
4-974-725-01 SCREW (M1.7X2.5), P
2
not supplied
MI-043 BOARD, COMPLETE
3
3-066-994-01 MF RUBBER
4
3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2
5
3-067-081-11 SHEET, POWER
6
not supplied
ML-023 BOARD, COMPLETE
7
1-681-511-11 FP-329 FLEXIBLE BOARD
8
3-067-006-01 RETAINER, FB PWB
9
3-989-735-81 SCREW (M1.7), LOCK ACE, P2
10
X-3951-556-1 PANEL ASSY, FRONT
11
3-067-007-01 SHEET, MUFFLE
12
X-3949-944-1 CAP ASSY, LENS
13
X-3951-455-1 COVER ASSY, JACK
14
3-066-974-01 ST COVER
15
3-067-008-01 CLAMP, PHOTO
16
not supplied
SE-121 BOARD, COMPLETE
17
1-681-508-21 FP-325 FLEXIBLE BOARD
18
X-3951-555-1 CABINET ASSY, TOP
19
3-989-735-01 SCREW (M1.7), LOCK ACE, P2
20
1-475-950-53 REMOTE COMMANDER (RMT-811)
21
3-053-056-01 LID, BATTERY CASE (FOR RMT-811)
22
3-068-834-01 SHEET, TS
MIC901 1-418-351-11 MICROPHONE UNIT
Cabinet (L) section
(See page 22, 23)
(See page 22, 23)
Cabinet (R) section
(See page 20)
(See page 20)
1
1
2
4
4
4
4
11
9
9
5
22
18
9
9
9
17
4
7
8
9
3
9
9
20
21
10
12
13
14
15
16
16
6
not
supplied
not
supplied
MIC901
19
Ver 1.1 2002. 06
— 20 —
3-1-2.
CABINET (R) SECTION
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
51
3-055-573-01 SCREW (M1.7), LOCK ACE, P2
52
X-3951-440-1 FRAME ASSY, BOTTOM
* 53
3-069-706-01 SHEET, TRIPOD CONDUCTIVE
54
3-055-257-01 TRIPOD (LARGE)
55
3-067-122-01 SHEET, SP INSULATING
56
3-959-978-02 CUSHION, PANEL
57
3-713-791-51 SCREW (M1.7X3.5), TAPPING, P2
58
not supplied
CK-102 BOARD, COMPLETE
59
1-476-611-11 SWITCH BLOCK, CONTROL (KP-1800)
60
3-055-324-01 KNOB, EJECT
61
X-3951-557-1 CABINET (R) ASSY
62
4-974-725-01 SCREW (M1.7X2.5), P
63
not supplied
PO-006 BOARD, COMPLETE
64
3-060-164-01 TAPE (B)
SP901
1-529-590-11 SPEAKER (2.0CM)
CK-102
A
D
B
C
A
D
B
C
LCD section
(See page 21)
(See page 21)
: BT3201 (Lithium battery) CK-102 board on the mount position.
not
supplied
not
supplied
not
supplied
not
supplied
SP901
51
51
52
53
54
55
57
58
59
60
57
61
56
63
62
64
Click on the first or last page to see other DCR-TRV30E service manuals if exist.