Sony DCR-TRV238E / DCR-TRV239E (serv.man3) Service Manual ▷ View online
— 9 —
DCR-TRV238E/TRV239E
1. MAIN PARTS
Note:
• Follow the disassembly procedure in the numerical order given.
• Items marked “*” are not stocked since they are seldom required for routine service.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The parts numbers of such as a cabinet are also appeared in this section.
Refer to the parts number mentioned below the name of parts to order.
1.
ORNAMENTAL PARTS
The components identified by mark
0
or
dotted line with mark
0
are critical for safety.
Replace only with part number specified.
Retainer Jack cover
3-072-344-01
3-072-344-01
Jack cover
3-072-343-01
3-072-343-01
MI screw (M2
×
4) (H)
3-067-347-01
MI screw (M2
×
4) (H)
3-067-347-01
MI screw (M2
×
4) (H)
3-067-347-01
CPC lid (BT)
3-072-271-01
3-072-271-01
Jack lid (2500)
Note: Disassembling the main unit
is necessary to replace it.
Note: Disassembling the main unit
is necessary to replace it.
Remote commander (RMT-814)
1-475-141-61
1-475-141-61
Battery case lid
3-742-854-01
3-742-854-01
— 10 —
DCR-TRV238E/TRV239E
2.
DISASSEMBLY
The following flow chart shows the disassembly procedure.
DCR-TR
V238E/TR
V239E
2-1. LCD unit, PD-156 board -1
2-2. LCD unit, PD-156 board -2
2-3. Front panel section
2-4. SI-032 board
2-5. Microphone
2-6. Cabinet (R) section
2-7. Lens section
2-19. Hinge section
2-17. Control switch block (CF-2500)
2-18 . Control switch block (FK-2500)
2-9. LB-076 board
2-8. EVF section
2-10. Battery panel section
2-11. Battery terminal board
2-12. Control switch block (SS-1380)
2-13. Cabinet (L) section
2-14. CS frame assembly (25)
2-15. VC-276 board
2-16. Mechanism deck
— 11 —
DCR-TRV238E/TRV239E
2-1.
LCD UNIT, PD-156 BOARD-1
NOTE: Follow the disassembly procedure in the numerical order given.
6
Claw
5
Claw
2
Two
claws
1
Four tapping screws (M1.7
×
5)
3
P cabinet (C (2))
4
Reversed the LCD unit
in the direction of the arrow
A
.
A
7
Indication LCD block assembly,
LCD holder, Back light
2-2.
LCD UNIT, PD-156 BOARD-2
PD-156
Board
8
Claw
4
LCD insulating sheet (SH)
A
q;
P frame (2)
6
Back light
(Cold cathode
fluorescent tube)
fluorescent tube)
1
Two tapping screws
(B1.7
×
6)
7
Screw
(M1.7
×
2.5), p
3
P cabinet (M) (2) assembly
9
Remove the PD-156 board
in the direction of the arrow
A
.
5
Liquid crystal
indicator module
2
Two claws
2
Four claws
Two claws
B
3
Remove the indication LCD block assembly
in the direction of the arrow
B
.
1
Push this point to
remove the two
claws.
claws.
— 12 —
DCR-TRV238E/TRV239E
2-3.
FRONT PANEL SECTION
2-4.
SI-032 BOARD
1
When removing Front panel section, do not
press down the drum of mechanism deck.
press down the drum of mechanism deck.
The drum of
mechanism deck.
mechanism deck.
2
MI screw
(M2
×
4) (H)
3
MI screw
(M2
×
4) (H)
6
FP-406 flexible
board (30P)
4
Two MI screws
(M2
×
4) (H)
Push the eject knob in
the direction of the arrow
the direction of the arrow
A
,
and open the cassette lid.
A
7
Front panel section
5
Claw
Remove it while taking
care as the FP-406 flexible
cable is connected.
care as the FP-406 flexible
cable is connected.
B
7
SI-032 board
1
Cushion (1), F
3
Tapping screw
(M1.7
×
5)
2
Two tapping screws
(M1.7
×
5)
6
Tapping screw
(M1.7
×
5)
4
Remove the FP-411 flexible board
in the direction of the arrow
B
.
5
Microphone
(4P)
Click on the first or last page to see other DCR-TRV238E / DCR-TRV239E (serv.man3) service manuals if exist.