Sony DCR-TRV16E / DCR-TRV18E Service Manual ▷ View online
— 8 —
DCR-TRV16E/TRV18E/TRV116E/TRV118E
1. MAIN PARTS
Note:
• Follow the disassembly procedure in the numerical order given.
• Items marked “*” are not stocked since they are seldom required for routine service.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The parts numbers of such as a cabinet are also appeared in this section.
Refer to the parts number mentioned below the name of parts to order.
1.
ORNAMENTAL PARTS
The components identified by mark
0
or
dotted line with mark
0
are critical for safety.
Replace only with part number specified.
COVER
COVER
Jack cover assembly
Note: Disassembling the main unit
is necessary to replace it.
Grip belt
Note: Disassembling the main unit
is necessary to replace it.
Screw
(M1.7
(M1.7
×
4),
lock ace, p2
3-989-735-81
3-989-735-81
CPC lid
3-067-025-01
3-067-025-01
Remote commander (RMT-814)
1-475-141-61
1-475-141-61
Battery case lid
3-742-854-01
3-742-854-01
— 9 —
DCR-TRV16E/TRV18E/TRV116E/TRV118E
2.
DISASSEMBLY
The following flow chart shows the disassembly procedure.
COVER
COVER
DCR-TR
V16E/TR
V18E/TR
V116E/TR
V118E
2-1. LCD section (PD-161 board)
2-2. EVF section (LB-077 board)
2-3. Front panel section
2-5. Top cabinet assembly
(page 11)
(page 12)
(page 13)
2-6. Cabinet (R) section
(page 13)
2-7. Battery panel section
(page 14)
2-8. EVF section
(page 14)
2-10. VA-117 board (1)
(page 16)
2-11. Main chassis complete section (page 17)
2-12. VA-117 board (2)
(page 18)
2-16. JK-217, JK-218 boards
(page 20)
2-14. Lens section
(page 19)
2-17. CK-108 board
(page 21)
2-18. Hinge assembly
(page 22)
2-19. Control switch block (PS-CX2670)
(page 23)
2-20. Memory stick connector
(TRV18E/TRV118E)
(TRV18E/TRV118E)
(page 24)
2-13. VC-280 board
(page 18)
(page 10)
(page 12)
2-4. MA-409, FB-219 boards
(page 15)
2-9. LB-077 board
(page 19)
2-15. Mechanism deck
— 10 —
DCR-TRV16E/TRV18E/TRV116E/TRV118E
2-1.
LCD SECTION (PD-161 BOARD)
NOTE: Follow the disassembly procedure in the numerical order given.
PD-161
B
B
A
A
7
P cabinet (c) assembly,
Indication LCD block assembly
P cabinet (c) assembly
5
P cabinet (M)
8
Liquid crystal
indicator module
9
Back light
(Cold cathode fluorescent tube)
1
Screw
(M2
×
4),
lock ace, p2
6
FP-441 flexible board
(Indication LCD block assembly)
(20P)
(20P)
2
Screw
(M2
×
4),
lock ace, p2
0
PD-161 board,
P frame assembly
3
Two screws
(M2
×
4),
lock ace, p2
4
Five claws
Caution
Caution
FP-441 flexible board
The
7
P cabinet (C) assembly is securely
fixed in the LCD unit by the five
4
claws.
Because the Indication LCD block assembly
installed in the Cabinet (C) assembly is
connected to the PD-161 board with the
FP-441 flexible board, the flexible board
may be damaged if the Cabinet (C)
assembly is removed forcibly.
Be careful not to damage the flexible board.
installed in the Cabinet (C) assembly is
connected to the PD-161 board with the
FP-441 flexible board, the flexible board
may be damaged if the Cabinet (C)
assembly is removed forcibly.
Be careful not to damage the flexible board.
Indication LCD
block assembly
block assembly
— 11 —
DCR-TRV16E/TRV18E/TRV116E/TRV118E
2-2.
EVF SECTION (LB-077 BOARD)
B
A
2
Two tapping screws
(M1.7
×
6)
4
VF cabinet (upper)
assembly
6
VF lens assembly
7
LB-077 board,
Lamp guide
q;
LB-077 board
9
Lamp guide
5
Three claws
Prism sheet
Illuminator
3
Two claws
8
Two claws
1
Raise the EVF in the
direction of the arrow
A
and slide it in the direction
of the arrow
of the arrow
B
.
When separating the
7
LB-077 board and
Lamp guide from the
6
VF lens assembly
by removing the three
5
claws, do not face
the side of the VF lens assembly on which
the LB-077 board is installed, downwards.
Because the Illuminator and others may fall
out of the VF lens assembly, hold the
illuminator and others using tape or paper
as shown to prevent them from falling.
Be careful on this point especially when
removing the LB-077 board and Lamp guide
because the three claws located in the VF
lens assembly are easy to break.
the LB-077 board is installed, downwards.
Because the Illuminator and others may fall
out of the VF lens assembly, hold the
illuminator and others using tape or paper
as shown to prevent them from falling.
Be careful on this point especially when
removing the LB-077 board and Lamp guide
because the three claws located in the VF
lens assembly are easy to break.
Hold the illuminator
and others using
tape or paper as
shown to prevent
them from falling.
and others using
tape or paper as
shown to prevent
them from falling.
Caution
Click on the first or last page to see other DCR-TRV16E / DCR-TRV18E service manuals if exist.