DOWNLOAD Sony DCR-TRV12E / DCR-TRV14E / DCR-TRV19 / DCR-TRV19E (serv.man4) Service Manual ↓ Size: 1.26 MB | Pages: 59 in PDF or view online for FREE

6-5

For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.

When performing only the adjustments, the lens block and boards
need not be disassembled.

Before performing the adjustments, check the data of page: 0,
address: 10 is “00”. If not, set data: 00 to this address.

1)

Connect the equipment for adjustments according to Fig. 6-1-3.

As removing the cabinet (R) assembly (removing CN4005 of the
VA-118 board) means removing the lithium 3V power supply
(BT5201 on the CK-129 board), data such as date, time, user-set
menus will be lost. After completing adjustments, reset these data.
But the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the lithium 3V power
supply is removed. (Refer to “6-4.Service Mode” for the self-
diagnosis data and the data on history of use.)

Setting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE

button.

The above procedure will enable the camera power to be turned
on with the control switch block (FK-CX4000) removed. After
completing adjustments, be sure to exit the “Forced Camera Power
ON Mode”.

Exiting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE

button.

3) Select page: 0, address: 01, and set data: 00.

Fig. 6-1-2.

1.5 m

Front of the lens

Pattern box

6-6

Fig. 6-1-3.

Adjustment remote
commander (RM-95)

AC power
adaptor 

AC IN

CPC-7 jig
(J-6082-382-A)

Screw 
(M1.7 

× 

4),

lock ace, p2

CPC lid

LANC jack

DC-IN connector

6-7

Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.

1.

POWER switch (FK-CX4000 block) ..................... CAMERA

2.

NIGHT SHOT switch (Lens block) ................................. OFF

3.

BACK LIGHT switch (CF-CX4000 block) ..................... OFF

4.

FUNCTION settings (Touch panel)

FOCUS (Page1) ................................................ MANUAL
SPOT METER (Page1) ............................................ AUTO
MANUAL SET of the MENU settings (Page1)

PROGRAM AE .................................................... AUTO
PICTURE EFFECT .................................................. OFF
WHITE BALANCE ............................................. AUTO

CAMERA SET of the MENU settings (Page1)

DIGITAL ZOOM ..................................................... OFF
16:9 WIDE ................................................................ OFF
STEADY SHOT ....................................................... OFF

SETUP MENU of the MENU settings (Page1)

DEMO MODE ......................................................... OFF

EXPOSURE (Page1) ................................................ AUTO

Basically carry out adjustments in the order given.

Fig. 6-1-4.

1)

Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 6-1-4. (Color reproduction
adjustment frame)

2)

Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)

3)

Flange back adjustment chart
Make the chart shown in Fig. 6-1-5 using A0 size (1189mm 

×

841mm) black and white vellum paper.

Fig. a

(Video output terminal

output waveform)

Fig. b (TV monitor picture)

Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.

Fig. 6-1-5.

Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.

6-8

When reading or writing the 1C page data, select page: 0, address:
10, and set data: 01, then select C page. The 1C page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
“00”.

1)

Connect the regulated power supply and the digital voltmeter
to the battery terminal as shown in Fig. 6-1-6.

2)

Adjust the output voltage of the regulated power supply so that
the digital voltmeter display is 6.0 ± 0.1Vdc.

3)

Turn off the power supply.

4)

Turn on the HOLD switch of the adjusting remote commander.

5)

Turn on the power supply.

6)

Perform the initialization of the data.

This is normal though the following message is indicated on the
LCD screen.

“FOR InfoLITHIUM BATTERY ONLY”

1.

Initialization of A, D page data

2.

Initialization of 8, C, 1C page data

3.

Initialization of E, F page data

fig. 6-1-6

Regulated power supply

Battery terminal

Digital volt meter