Sony DCR-SX45 / DCR-SX45E / DCR-SX65 / DCR-SX65E / DCR-SX85 / DCR-SX85E (serv.man2) Service Manual ▷ View online
DCR-SX45/SX45E/SX65/SX65E/SX85/SX85E_L2
1-2E
1-3-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
0
4
0
0
Non-standard battery is used.
Use the InfoLITHIUM battery.
C
0
6
0
0
The battery pack temperature is high.
Change the battery pack or replace it in a cool place.
C
1
3
0
1
Memory card is unformatted.
Memory card is broken.
Memory card is broken.
Format the Memory card.
Insert a new Memory card.
Insert a new Memory card.
E
2
0
0
0
Flash memory data are rewritten.
Make flash memory data correct value. (Note 1)
E
6
1
0
0
Difficult to adjust focus
(Cannot initialize focus).
(Cannot initialize focus).
Inspect the lens block focus reset sensor (pin 8 of CN1003 on the
VC-616 board) when focusing is performed when the focus button is
pressed in the focus manual mode, and the focus motor drive circuit
(IC5401 on the VC-616 board) when the focusing is not performed.
VC-616 board) when focusing is performed when the focus button is
pressed in the focus manual mode, and the focus motor drive circuit
(IC5401 on the VC-616 board) when the focusing is not performed.
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens).
(Cannot initialize zoom lens).
Inspect the lens block zoom reset sensor (pin 0 of CN1003 on the
VC-616 board) when zooming is performed when the zoom lever is
operated, or the zoom motor drive circuit (IC5401 on the VC-616
board) when zooming is not performed.
VC-616 board) when zooming is performed when the zoom lever is
operated, or the zoom motor drive circuit (IC5401 on the VC-616
board) when zooming is not performed.
E
6
1
1
1
The abnormalities in initialization of the focus
lens and the abnormalities in initialization of the
zoom lens occurred simultaneously.
lens and the abnormalities in initialization of the
zoom lens occurred simultaneously.
Check both E: 61: 00 and E: 61: 10 of the self-diagnosis code.
E
6
2
0
0
Handshake correction function does not
work well. (With PITCH angular velocity
sensor output stopped.)
work well. (With PITCH angular velocity
sensor output stopped.)
Inspect PITCH angular velocity sensors (SE9301 on the MS-453
board) peripheral circuits.
board) peripheral circuits.
E
6
2
0
1
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Inspect YAW angular velocity sensors (SE9301 on the MS-453 board)
peripheral circuits.
peripheral circuits.
E
9
2
0
1
Battery current value goes over the max
discharge current.
discharge current.
Check the remaining battery power because this symptom may be
depended on the remaining battery level, and confirm whether or not
the symptom is occurred after replacing the battery. If the symptom
is still occurred, overhaul inspection is needed. Check each output of
DC-DC converter (IC4701) on the VC-616 board with the AC adaptor
connected to DC JACK (J901) on the VC-616 board. (the minimum
connection to periphery)
depended on the remaining battery level, and confirm whether or not
the symptom is occurred after replacing the battery. If the symptom
is still occurred, overhaul inspection is needed. Check each output of
DC-DC converter (IC4701) on the VC-616 board with the AC adaptor
connected to DC JACK (J901) on the VC-616 board. (the minimum
connection to periphery)
E
9
4
0
0
Fault of writing to or erasing the flash memory. Inspect the flash memory (IC7801 on the VC-616 board).
E
9
4
0
1
Internal flash memory fault.
Inspect the flash memory (IC7801 on the VC-616 board).
Note 1 : Start the Adjust Manual in the Adjust Station and refer to the “DESTINATION DATA WRITE”.
DCR-SX45/SX45E/SX65/SX65E/SX85/SX85E_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link
ACCESSORIES
ASSEMBLY
VC-616
DD-340
5
Front Panel Section
3
Cabinet Top Assy
Control Switch Block
(PS36500)
(PS36500)
9
VC-616 Board
q;
Lens Section
• CD-772 Board
1
Cabinet (L) Assy
7
Cabinet R Section
• PD-428 Board
• FP-1308 Flexible Board
• FP-1308 Flexible Board
4
Battery Panel Section
• MS-453 Board
• FP-1309 Flexible Board
• FP-1309 Flexible Board
8
DD-340 Board
2
BM Cabinet
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not sup-
plied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF:
uF:
μF
• COILS
uH:
uH:
μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...:
In each case, u: μ, for example:
uA...:
μA... , uPA... , μPA... ,
uPB...
,
μPB... , μPC... , μPC... ,
uPD...,
μPD...
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
• Abbreviation
AR :
AR :
Argentine
model
AUS :
Australian
model
CH :
Chinese
model
CND :
Canadian
model
NE
: North European model
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
DCR-SX45/SX45E/SX65/SX65E/SX85/SX85E_L2
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at
the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that
a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DCR-SX45/SX45E/SX65/SX65E/SX85/SX85E_L2
2-3
#1: M1.7 X 2.5
(Black)
2-635-562-11
2-635-562-11
2.5
1.7
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION-1
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-265-543-01
CABINET (BM (365))
2
3-283-643-01 SCREW,
TRIPOD
3
4-265-542-01 RETAINER,
TRIPOD
4
A-1806-120-A CABINET (L) ASSY (365 SL) (SILVER)
4
A-1806-121-A CABINET (L) ASSY (365 BK) (BLACK)
4
A-1806-122-A CABINET (L) ASSY (365 BL) (BLUE)
4
A-1806-123-A CABINET (L) ASSY (365 RD) (RED)
5
4-265-549-01
BELT (K), 11 TYPE GRIP (SILVER, BLACK)
5
4-265-548-11
BELT (A), 11 TYPE GRIP (BLUE)
5
4-265-548-21
BELT (A), 11 TYPE GRIP (RED)
6
1-838-712-11
CABLE, BUILT-IN USB
7
4-265-544-01 GUARD
(365),
BELT
8
4-265-545-01
SHEET METAL (365), CONNECT
9
4-265-546-01
SHEET METAL (R (365)), BELT
10
4-272-621-01
SHEET (UA), SHIELD (Note 2)
#1
2-635-562-11 SCREW
(M1.7)
#2
2-635-562-31 SCREW
(M1.7)
#11
3-078-890-11 SCREW,
TAPPING
#12
3-080-204-21 SCREW,
TAPPING,
P2
1. Remove to numerical order (
1
to
2
) in the left figure.
DISASSEMBLY
1
Disconnect → #12 X 1 → #2 X 5 → #1 X 1
Screw
#2
#1
#2
#2
#12
#2
#2
#2
#2
#11
1
(Claws)
1
(Claws)
2
1
1
4
3
5
6
7
9
10
(Note 2)
8
2
2
(Claws)
Overall Section-2
(See page 2-4)
(Note 1)
Left View
Left View
Right View
Left View
Bottom View
Back View
#12
Disconnect
#2
#2
#2
#2
#1
Bottom View
#2
#2
2
#2 X 4
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
3-078-890-11
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
Note
Note 1: Refer to "Assembly-1: Installation Cautions of the USB
Harness and the DC Jack Harness".
Note 2: Refer to "Assembly-2: Installation Cautions of the Shield Sheet
(UA)".
Click on the first or last page to see other DCR-SX45 / DCR-SX45E / DCR-SX65 / DCR-SX65E / DCR-SX85 / DCR-SX85E (serv.man2) service manuals if exist.