Sony DCR-SR50E / DCR-SR60 / DCR-SR60E / DCR-SR70E / DCR-SR80 / DCR-SR80E (serv.man2) Service Manual ▷ View online
1-2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR50E/SR60/SR60E/SR70E/SR80/SR80E_L2
1-3. SELF-DIAGNOSIS FUNCTION
1-3-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
1-3-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
LCD screen shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
LCD screen shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
1 1
3 1
C
Repaired by:
Refer to “1-3-3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
H : Corrected by dealer
E : Corrected by service
engineer
LCD screen
C : 3 1 : 1 1
1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR50E/SR60/SR60E/SR70E/SR80/SR80E_L2
1-3-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
3
2
2
0
3
1
4
0
4
0
6
1
6
1
6
1
6
2
6
2
9
4
9
4
Detailed
Code
0
0
0
0
0
2
5
0
0
0
0
0
0
0
0
1
0
0
1
0
1
1
0
0
0
1
0
0
0
1
-
Symptom/State
Non-standard battery is used.
Disk is faulty.
Disk access error
Codec IC dose not return any reply
EEPROM data are rewritten.
Drive fault
Codec IC fault
Audio Codec IC fault
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Fault of writing to or erasing the
flashmemory
flashmemory
Fault of writing to or erasing EEPROM
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Make EEPROM data correct value. (Note 1)
Inspect or replacement of the hard disk drive
Inspect or replacement of the codec IC (IC2301on the VC-463
board) peripheral circuits
board) peripheral circuits
Inspect or replacement of the Audio Codec IC (IC2301 on the
VC-463 board) peripheral circuits
VC-463 board) peripheral circuits
Inspect the lens block focus MR sensor (pin 2, 4 of CN1501
on the VC-463 board) when focusing is performed when the
focus buttons of the touch panel are pressed in the focus manual
mode, and the focus motor drive circuit (IC1501 on the VC-463
board) when the focusing is not performed.
on the VC-463 board) when focusing is performed when the
focus buttons of the touch panel are pressed in the focus manual
mode, and the focus motor drive circuit (IC1501 on the VC-463
board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (pin w; of CN1501 on
the VC-463 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC1501 on
the VC-463 board) when zooming is not performed.
the VC-463 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC1501 on
the VC-463 board) when zooming is not performed.
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC1501 on the VC-463 board).
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC1501 on the VC-463 board).
Inspect PITCH angular velocity sensors (SE701 on the CD-652
board) peripheral circuits.
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE702 on the CD-652
board) peripheral circuits.
board) peripheral circuits.
Inspect the flash memory (IC2401 on the VC-463 board). (Note 1)
Inspect the EEPROM (IC2303 on the VC-463 board). (Note 1)
Note 1:
Refer to “ 11-2. Record of Self-diagnosis Check” of “2-5. SERVICE MODE”, ADJ 9-852-138-51).
1-4
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR50E/SR60/SR60E/SR70E/SR80/SR80E_L2
1-4. PRECAUTION ON REPLACING THE VC-463 BOARD
Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc., check the data setting (Exif Model Data) is right. If not, rewrite to the right
value.
When the data has changed because of board replaceing etc., check the data setting (Exif Model Data) is right. If not, rewrite to the right
value.
Writing Method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: B6 to B8, and set the Exif Model Data.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: B6 to B8, and set the Exif Model Data.
Note:
To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Address
B6
B7
B8
Page
A
A
A
Data
DCR-SR60
36
30
00
DCR-SR80
38
30
00
Address
B6
B7
B8
Page
A
A
A
Data
DCR-SR50E
35
30
45
DCR-SR60E
36
30
45
DCR-SR70E
37
30
45
DCR-SR80E
38
30
45
Exif Model Data
1-5
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR50E/SR60/SR60E/SR70E/SR80/SR80E_L2
1. SERVICE NOTE
1-2. 強制電源ONモードの設定
調整リモコン（RM-95またはNEW
LANC
JIG）を使用して，電源を入れることが出来ます。
カムコーダの操作は調整リモコンで行えます。
1-2-1. 強制Movie電源ONモードの設定
1) ページ：0，アドレス：01にデータ：01をセット。
2) ページ：A，アドレス：10にデータ：01をセットしPAUSE（Write）ボタンを押す。
1-2-2. 強制Play/Edit電源ONモードの設定
1) ページ：0，アドレス：01にデータ：01をセット。
2) ページ：A，アドレス：10にデータ：02をセットしPAUSE（Write）ボタンを押す。
1-2-3. 強制電源ONモードの解除
1) ページ：0，アドレス：01にデータ：01をセット。
2) ページ：A，アドレス：10にデータ：00をセットしPAUSE（Write）ボタンを押す。
3) ページ：0，アドレス：01にデータ：00をセット。
3) ページ：0，アドレス：01にデータ：00をセット。
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。
方法：
DC入力端子を使用する。（ACアダプタ（AC-L25A/L25Bなど）を使用する。）
DC入力端子を使用する。（ACアダプタ（AC-L25A/L25Bなど）を使用する。）
Click on the first or last page to see other DCR-SR50E / DCR-SR60 / DCR-SR60E / DCR-SR70E / DCR-SR80 / DCR-SR80E (serv.man2) service manuals if exist.