Sony DCR-SR35E / DCR-SR36E / DCR-SR45 / DCR-SR45E / DCR-SR46 / DCR-SR46E / DCR-SR55E / DCR-SR65 / DCR-SR65E / DCR-SR75E / DCR-SR85 / DCR-SR85E (serv.man2) Service Manual ▷ View online
1-2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR35E/SR36E/SR45/SR45E/SR46/SR46E/
SR55E/SR65/SR65E/SR75E/SR85/SR85E_L2
SR55E/SR65/SR65E/SR75E/SR85/SR85E_L2
1-3-3. Self-diagnosis Code Table
C
C
C
E
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
2
0
3
1
6
1
6
1
6
1
6
2
6
2
9
4
Detailed
Code
0
0
0
1
0
2
0
0
0
0
0
0
1
0
1
1
0
0
0
1
0
0
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Disk access error
Flash memory data are rewritten.
Drive fault
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Fault of writing to or erasing the flash
memory
memory
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
camcorder again.
camcorder again.
Make flash memory data correct value. (Note 1)
Inspect or replacement of the hard disk drive
Inspect the lens block focus reset sensor (pin 7 of CN5101 on
the VC-518 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor driver circuit (IC5401 (Non MEGA model)
or IC5301 (MEGA model) on the VC-518 board) when focusing
is not performed.
the VC-518 board) when focusing is performed when the focus
buttons of the touch panel are pressed in the focus manual mode,
and the focus motor driver circuit (IC5401 (Non MEGA model)
or IC5301 (MEGA model) on the VC-518 board) when focusing
is not performed.
Inspect the lens block zoom reset sensor (pin qa of CN5101 on
the VC-518 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5401 (Non
MEGA model) or IC5301 (MEGA model) on the VC-518 board)
when zooming is not performed.
the VC-518 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5401 (Non
MEGA model) or IC5301 (MEGA model) on the VC-518 board)
when zooming is not performed.
Check whether the flexible board of the lens is broken, and
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5401 (Non MEGA model) or IC5301 (MEGA model) on the
VC-518 board).
check whether it is inserted imperfectly. If there is no problem in
the flexible board, inspect the focus/zoom motor drive circuit
(IC5401 (Non MEGA model) or IC5301 (MEGA model) on the
VC-518 board).
Inspect PITCH angular velocity sensors (SE7002 on the CD-
672/CD-687 board) peripheral circuits (MEGA model only).
672/CD-687 board) peripheral circuits (MEGA model only).
Inspect YAW angular velocity sensors (SE7001 on the CD-672/
CD-687 board) peripheral circuits (MEGA model only).
CD-687 board) peripheral circuits (MEGA model only).
Inspect the flash memory (IC2101 on the VC-518 board). (Note 1)
Note 1:
Refer to Service Manual, ADJ (“1-4. DESTINATION DATA WRITE”).
Note 2:
Non MEGA model: DCR-SR35E/SR36E/SR45/SR45E/SR46/SR46E
MEGA model: DCR-SR55E/SR65/SR65E/SR75E/SR85/SR85E
MEGA model: DCR-SR55E/SR65/SR65E/SR75E/SR85/SR85E
1-3
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR35E/SR36E/SR45/SR45E/SR46/SR46E/
SR55E/SR65/SR65E/SR75E/SR85/SR85E_L2
SR55E/SR65/SR65E/SR75E/SR85/SR85E_L2
1-4-1. Laser Printed Unit
The model display adopts the laser printing method.
Therefore, the HDD Lid Assy for replacement differs depending on
the destination.
As similar displays are provided, choose the suitable one for order.
Therefore, the HDD Lid Assy for replacement differs depending on
the destination.
As similar displays are provided, choose the suitable one for order.
Note:
After replacing the HDD Lid Assy, the serial number for it
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change
the serial number in the repair data.
will be changed to the one exclusive for service use.
Inform a customer of the serial number change and change
the serial number in the repair data.
DCR-SR35E (AEP, UK, NE)
DCR-SR36E (AEP, UK)
DCR-SR36E (NE)
DCR-SR45 (E, AR)
DCR-SR45E (NE)
DCR-SR45E (E, HK, AUS, TH)
DCR-SR45 (KR)
DCR-SR46E (NE)
DCR-SR46E (E, HK, AUS, TH)
Part No.
Description
A-1498-616-A LID (35), SERVICE (HDD)
Part No.
Description
A-1498-617-A LID (36H), SERVICE (HDD)
Part No.
Description
A-1498-618-A LID (36L), SERVICE (HDD)
Part No.
Description
A-1498-622-A LID (45EA), SERVICE (HDD)
Part No.
Description
A-1498-621-A LID (45E), SERVICE (HDD)
Part No.
Description
A-1498-619-A LID (45), SERVICE (HDD)
Part No.
Description
A-1498-620-A LID (45K), SERVICE (HDD)
Part No.
Description
A-1498-625-A LID (46E), SERVICE (HDD)
Part No.
Description
A-1498-626-A LID (46EA), SERVICE (HDD)
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
Serial No.
DCR-SR46 (KR)
Part No.
Description
A-1498-624-A LID (46K), SERVICE (HDD)
Serial No.
1-4. PRECAUTION ON REPLACING THE HDD LID ASSY
[Repair Operation]
This unit has two kinds of HDD Lid Assy.
1.
This unit has two kinds of HDD Lid Assy.
1.
Laser Print HDD Lid Assy
Replace the laser print HDD Lid Assy for a new one.
Replace the laser print HDD Lid Assy for a new one.
2.
No Laser Print Cabinet (Model number label)
Swap the model number label for a new one after exchanging the HDD Lid Assy.
Swap the model number label for a new one after exchanging the HDD Lid Assy.
Note:
Repair and return customers’ unit as same as customers send the repair unit to your service center.
(Do not mix the laser print HDD Lid Assy with No laser print HDD Lid Assy.)
(Do not mix the laser print HDD Lid Assy with No laser print HDD Lid Assy.)
Ver. 1.4 2008.11
The changed portions from
Ver. 1.3 are shown in blue.
Ver. 1.3 are shown in blue.
1-4
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR35E/SR36E/SR45/SR45E/SR46/SR46E/
SR55E/SR65/SR65E/SR75E/SR85/SR85E_L2
SR55E/SR65/SR65E/SR75E/SR85/SR85E_L2
1-4-2. Precaution on Replacing the HDD Lid Assy for KR Models (SR45/SR46)
The date of manufacture on the labels should be the same as the previous HDD Lid Assy (circled portions shown on the below).
Example: For the figure below, attach the “2007.12” label.
Example: For the figure below, attach the “2007.12” label.
* The replacement label and “inset (how to affix)” are supplied together with HDD Lid Assy for service.
DCR-SR45
DCR-SR46
*
Manufacturing year
* Affix the label
*
Manufacturing year
* Affix the label
1-4-3. Unit with Model Number Label
Repaste the model number label after replacing HDD Lid assy.
Part No.
Description
A-1454-416-A
X-2187-939-1
LID ASSY (SSGE), HDD
(SR45: US, CND/SR45E: CH/SR46: US, CND/SR46E: CH
SR65: US, CND/SR65E: CH/SR85: US, CND/SR85E: CH)
LID ASSY, HDD
(SR45: BR/SR55E/SR65: E, KR, J/SR65E: NE, E, HK, AUS,
(SR45: US, CND/SR45E: CH/SR46: US, CND/SR46E: CH
SR65: US, CND/SR65E: CH/SR85: US, CND/SR85E: CH)
LID ASSY, HDD
(SR45: BR/SR55E/SR65: E, KR, J/SR65E: NE, E, HK, AUS,
TH
/
SR75E/SR85: E, BR, KR, JE/SR85E: NE, E, HK, AUS,
TH
, JE)
Model Number Label
Ver. 1.2 2008.05
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
1-5
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-SR35E/SR36E/SR45/SR45E/SR46/SR46E/
SR55E/SR65/SR65E/SR75E/SR85/SR85E_L2
SR55E/SR65/SR65E/SR75E/SR85/SR85E_L2
1. SERVICE NOTE
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなりま
す。
これを避けるため，下記の方法を用いてください。
す。
これを避けるため，下記の方法を用いてください。
方法：
DC入力端子を使用する。（ACアダプタ（AC-L200/L200B）を使用する。）
DC入力端子を使用する。（ACアダプタ（AC-L200/L200B）を使用する。）
1-2. VC-518基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
ADJ編を参照して，「DESTINATION DATA WRITE」を行ってください。
ADJ編を参照して，「DESTINATION DATA WRITE」を行ってください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
ADJ編を参照して，「USB SERIAL No. INPUT」を行ってください。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
ADJ編を参照して，「USB SERIAL No. INPUT」を行ってください。
1 1
3 1
C
対応者分類
「1 -3 -3 . 自己診断コード表」
を参照
対応方法の違いにより分類
例
例
31 ･･ ･テープを入れ直す
32 ･･ ･電源を入れ直す
ブロック分類
詳細コード
3.2Hz点滅
C ：お客さま自身で対応
H ：販売店で対応
E ：サービスエンジニア
H ：販売店で対応
E ：サービスエンジニア
で対応
LCD画面
C : 3 1 : 1 1
1-3. 自己診断機能
1-3-1.
自己診断機能について
本機の動作に不具合が生じたとき，自己診断機能が働き，
L C D 画面に，どう処置したらよいか判断できる表示を行い
ます。自己診断機能については取扱説明書にも掲載されて
います。
L C D 画面に，どう処置したらよいか判断できる表示を行い
ます。自己診断機能については取扱説明書にも掲載されて
います。
1-3-2.
自己診断表示
本機の動作に不具合が生じたとき，L C D 画面のカウンタ表
示部分がアルファベットと数字の4 桁表示になり，3 . 2 H z で
点滅します。この5 文字の表示によって対応者分類および不
具合の生じたブロックの分類，不具合の詳細コードを示し
ます。
示部分がアルファベットと数字の4 桁表示になり，3 . 2 H z で
点滅します。この5 文字の表示によって対応者分類および不
具合の生じたブロックの分類，不具合の詳細コードを示し
ます。
Click on the first or last page to see other DCR-SR35E / DCR-SR36E / DCR-SR45 / DCR-SR45E / DCR-SR46 / DCR-SR46E / DCR-SR55E / DCR-SR65 / DCR-SR65E / DCR-SR75E / DCR-SR85 / DCR-SR85E (serv.man2) service manuals if exist.