Sony DCR-SR32E / DCR-SR33E / DCR-SR42 / DCR-SR42A / DCR-SR42E / DCR-SR52E / DCR-SR62 / DCR-SR62E / DCR-SR72E / DCR-SR82 / DCR-SR82C / DCR-SR82E (serv.man2) Service Manual ▷ View online
1-1
DCR-SR32E/SR33E/SR42/SR42A/SR42E/SR52E/SR62/SR62E/SR72E/SR82/SR82C/SR82E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200/L200B).
1-2. SELF-DIAGNOSIS FUNCTION
1-2-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do. This function consists of two display; self-diagnosis display and
service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the LCD screen what to
do. This function consists of two display; self-diagnosis display and
service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
1-2-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
LCD screen shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
LCD screen shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
1 1
3 1
C
Repaired by:
Refer to “1-2-3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
H : Corrected by dealer
E : Corrected by service
engineer
LCD screen
C : 3 1 : 1 1
1-2
DCR-SR32E/SR33E/SR42/SR42A/SR42E/SR52E/SR62/SR62E/SR72E/SR82/SR82C/SR82E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-2-3. Self-diagnosis Code Table
C
C
C
C
E
E
E
E
E
E
E
Block
Function
0
4
1
3
1
3
3
2
2
0
3
1
6
1
6
1
6
2
6
2
9
4
Detailed
Code
0
0
0
1
0
2
6
0
0
0
0
0
1
0
1
1
0
0
0
1
0
0
Symptom/State
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
“Memory Stick Duo” is broken.
Disc access error
Difficult to adjust focus
(Cannot initialize focus)
(Cannot initialize focus)
EEPROM data are rewritten.
Drive fault
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
work well. (With YAW angular velocity
sensor output stopped.)
Fault of writing to or erasing the
flashmemory
flashmemory
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
camcorder again
camcorder again
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin 7 of
CN5301 on the VC-489 board). If it is OK, check the focus
motor drive IC (IC5601 on the VC-489 board: SR32E/SR33E/
SR42/SR42A/SR42E, IC5502 on the VC-489 board: SR52E/
SR62/SR62E/SR72E/SR82/SR82C/SR82E).
recover, check the focus MR sensor of lens block (pin 7 of
CN5301 on the VC-489 board). If it is OK, check the focus
motor drive IC (IC5601 on the VC-489 board: SR32E/SR33E/
SR42/SR42A/SR42E, IC5502 on the VC-489 board: SR52E/
SR62/SR62E/SR72E/SR82/SR82C/SR82E).
Make EEPROM data correct value.
Inspect or replacement of the hard disk drive.
Inspect the lens block zoom MR sensor (pin qa of CN5301 on
the VC-489 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5601 on
the VC-489 board: SR32E/SR33E/SR42/SR42A/SR42E, IC5502
on the VC-489 board: SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E) when zooming is not performed.
the VC-489 board) when zooming is performed when the zoom
lever is operated, and the zoom motor drive circuit (IC5601 on
the VC-489 board: SR32E/SR33E/SR42/SR42A/SR42E, IC5502
on the VC-489 board: SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E) when zooming is not performed.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Inspect PITCH angular velocity sensors (SE7002 on the CD-672
board) peripheral circuits.(SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E)
board) peripheral circuits.(SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E)
Inspect YAW angular velocity sensors (SE7001 on the CD-672
board) peripheral circuits.(SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E)
board) peripheral circuits.(SR52E/SR62/SR62E/SR72E/SR82/
SR82C/SR82E)
Inspect the flash memory (IC2201 on the VC-489 board).
1-3
DCR-SR32E/SR33E/SR42/SR42A/SR42E/SR52E/SR62/SR62E/SR72E/SR82/SR82C/SR82E_L2
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-3. PRECAUTION ON REPLACING THE VC-489 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-4. USING SERVICE JIG
Connect the extension cable between CN4008 on the DA-039 board and CN1005 on the VC-489 board.
CN4008
CN1005
DA-039 board (side B)
VC-489 board (side B)
Extension cable (100P)
1-4
DCR-SR32E/SR33E/SR42/SR42A/SR42E/SR52E/SR62/SR62E/SR72E/SR82/SR82C/SR82E_L2
(ENGLISH)
1-5. PRECAUTION ON REPLACING
1-5. PRECAUTION ON REPLACING
THE CABINET BOTTOM
(DCR-SR32E)
(DCR-SR32E)
* Cabinet bottom is registered as “bottom, cabinet” in the parts list.
The model display adopts the laser printing method.Therefore, the
cabinet bottom (BOTTOM, CABINET) for replacement differs
depending on the destination.
As similar displays are provided, choose the suitable one for order.
cabinet bottom (BOTTOM, CABINET) for replacement differs
depending on the destination.
As similar displays are provided, choose the suitable one for order.
Note1: After replacing the cabinet bottom (BOTTOM, CABINET),
the serial number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
the serial number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and change the serial
number in the repair data.
(JAPANESE)
1-5. キャビネットボトム 交換時の注意
1-5. キャビネットボトム 交換時の注意
(DCR-SR32E)
*
キャビネットボトムは部品表で“bottom, cabinet”とし
て登録されています。
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネットボトムは仕向けにより異な
ります。類似の表示もありますので，該当するものを選ん
この為，交換用のキャビネットボトムは仕向けにより異な
ります。類似の表示もありますので，該当するものを選ん
で注文して下さい。
注意1 : キャビネットボトム交換後はシリアルナンバーが
サービス専用のシリアルナンバーに変更されます。お客様
サービス専用のシリアルナンバーに変更されます。お客様
への案内と修理データのシリアルナンバー変更を行ってく
ださい。
ださい。
DCR-SR32E
(AEP, UK Models)
(AEP, UK Models)
Part No.
A-1246-539-A
Description
BOTTOM (SR-32E-1), CABINET
Serial No.
Click on the first or last page to see other DCR-SR32E / DCR-SR33E / DCR-SR42 / DCR-SR42A / DCR-SR42E / DCR-SR52E / DCR-SR62 / DCR-SR62E / DCR-SR72E / DCR-SR82 / DCR-SR82C / DCR-SR82E (serv.man2) service manuals if exist.