Sony DCR-SR21 / DCR-SR21E / DCR-SX21 / DCR-SX21E / DCR-SX22 / DCR-SX22E (serv.man2) Service Manual ▷ View online
DCR-SR21/SR21E/SX21/SX21E_L2
1-2E
1-3-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
0
4
0
0
Non-standard battery is used.
Use the InfoLITHIUM battery.
C
0
6
0
0
The battery pack temperature is high.
Change the battery pack or replace it in a cool place.
C
1
3
0
1
Memory card is unformatted.
Memory card is broken.
Memory card is broken.
Format the Memory card.
Insert a new Memory card.
Insert a new Memory card.
C
1
3
0
2
Disc access error.
Remove the power source. Reconnect it again and operate your
camcorder again.
camcorder again.
E
2
0
0
0
Flash memory data are rewritten.
Make flash memory data correct value. (Note 1)
E
3
1
0
0
Drive fault
Turn power off and turn power on again.
E
6
1
0
0
Difficult to adjust focus
(Cannot initialize focus).
(Cannot initialize focus).
Inspect the lens block focus reset sensor (pin 8 of CN5401 on the
VC-611 (F) /(H) board) when focusing is performed when the focus
button is pressed in the focus manual mode, and the focus motor drive
circuit (IC5401 on the VC-611 (F) /(H) board) when the focusing is
not performed.
VC-611 (F) /(H) board) when focusing is performed when the focus
button is pressed in the focus manual mode, and the focus motor drive
circuit (IC5401 on the VC-611 (F) /(H) board) when the focusing is
not performed.
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens).
(Cannot initialize zoom lens).
Inspect the lens block zoom reset sensor (pin 0 of CN5401 on the
VC-611 (F) /(H) board) when zooming is performed when the zoom
lever is operated, or the zoom motor drive circuit (IC5401 on the VC-
611 (F) /(H) board) when zooming is not performed.
VC-611 (F) /(H) board) when zooming is performed when the zoom
lever is operated, or the zoom motor drive circuit (IC5401 on the VC-
611 (F) /(H) board) when zooming is not performed.
E
6
1
1
1
The abnormalities in initialization of the focus
lens and the abnormalities in initialization of the
zoom lens occurred simultaneously.
lens and the abnormalities in initialization of the
zoom lens occurred simultaneously.
Check both E: 61: 00 and E: 61: 10 of the self-diagnosis code.
E
9
2
0
1
Battery current value goes over the max
discharge current.
discharge current.
Check the remaining battery power because this symptom may be
depended on the remaining battery level, and confirm whether or not
the symptom is occurred after replacing the battery. If the symptom
is still occurred, overhaul inspection is needed. Check each output of
DC-DC converter (IC4701) on the VC-611 (F) /(H) board with the AC
adaptor connected to DC JACK (J901) on the VC-611 (F) /(H) board.
(the minimum connection to periphery)
depended on the remaining battery level, and confirm whether or not
the symptom is occurred after replacing the battery. If the symptom
is still occurred, overhaul inspection is needed. Check each output of
DC-DC converter (IC4701) on the VC-611 (F) /(H) board with the AC
adaptor connected to DC JACK (J901) on the VC-611 (F) /(H) board.
(the minimum connection to periphery)
E
9
4
0
0
Fault of writing to or erasing the flash memory. Inspect the flash memory (IC7801 on the VC-611 (F) /(H) board).
Note 1 : Start the Adjust Manual in the Adjust Station and refer to the “DESTINATION DATA WRITE”.
DCR-SR21/SR21E/SX21/SX21E_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link
ACCESSORIES
ASSEMBLY
VC-61
1
SR21/SR21E
SR21/SR21E
SX21/SX21E
SX21/SX21E
4
HDD
1
F Panel Assy
2
Top Cabinet Assy
6
Control Switch Block
(PS24400)
q;
VC-611 (F)/(H) Board
9
Lens Block
• CD-801 Board
3
Cabinet (G )Assy
7
Cabinet (R) Section
• PD-426 Board
• FP-1479 Flexible Board
• FP-1479 Flexible Board
8
Battery Panel Section
• MS-451 Board
• FP-1290 Flexible Board
• FP-1290 Flexible Board
2
Top Cabinet Assy
6
Control Switch Block
(PS24400)
3
Cabinet (G )Assy
5
HDD Holder
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not sup-
plied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF:
uF:
μF
• COILS
uH:
uH:
μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...:
In each case, u: μ, for example:
uA...:
μA... , uPA... , μPA... ,
uPB...
,
μPB... , μPC... , μPC... ,
uPD...,
μPD...
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian Model
CH
AR : Argentine model
AUS : Australian model
BR : Brazilian Model
CH
:
Chinese
model
CND : Canadian model
MX :
MX :
Mexican
model
NE : North European model
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
DCR-SR21/SR21E/SX21/SX21E_L2
2-2
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at
the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that
a wire is snapped.
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DCR-SR21/SR21E/SX21/SX21E_L2
2-3
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION-1
(SX21/SX21E)
Refer to page 2-4 about SR21/SR21E.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1. Remove to numerical order (
1
to
3
) in the left figure.
DISASSEMBLY
1
#2 X 1 → #12 X 2 → #2 X 1
Screw
1
1
(Note 1)
2
1
3
2
(Note 2)
2
3
OVERALL SECTION-2
(See page 2-5)
#2
#12
#12
#2
#2
#2
1
(Claws)
2
(Claw)
2
(Claws)
3
(Claw)
2
#2 X 3
#2
Left View
Back View
Bottom View
#12
#2
Right View
Left View
#2
#2
#2
#2
#12
Left View
Bottom View
Note 2: Refer to "Assembly-1: Installation Cautions of DC-IN Harness".
3
#2 X 3 → #12 X 1
Note
Note 1:
d
2
1
1
2
b
a
c
d
REMOVING METHOD OF F PANEL ASSY
While pushing to the a portion,
twist the F panel assy in the
direction of the arrow b.
twist the F panel assy in the
direction of the arrow b.
While pulling the belt sheet metal
(front 244) in the direction of the
arrow c, and removing the F panel
assy in the direction of the arrow d.
(front 244) in the direction of the
arrow c, and removing the F panel
assy in the direction of the arrow d.
Belt sheet metal
(front 244)
(front 244)
F panel assy
1
A-1840-005-A PANEL ASSY (B), F (BLACK) (Note 1)
1
A-1840-006-A PANEL ASSY (S), F (SILVER) (Note 1)
2
A-1790-716-A CABINET (G (244)) ASSY (Note 2)
3
A-1840-020-A CABINET (246) ASSY (B), TOP (BLACK)
3
A-1840-021-A CABINET (246) ASSY (S), TOP (SILVER)
#2
2-635-562-31 SCREW
(M1.7)
#12
3-080-204-21 SCREW,
TAPPING,
P2
Click on the first or last page to see other DCR-SR21 / DCR-SR21E / DCR-SX21 / DCR-SX21E / DCR-SX22 / DCR-SX22E (serv.man2) service manuals if exist.