Sony DCR-SC100 / DCR-SC100E Service Manual ▷ View online
— 1 —
MICROFILM
SERVICE MANUAL
US Model
Canadian Model
DCR-SC100
AEP Model
UK Model
E Model
Tourist Model
DCR-SC100E
For MECHANISM ADJUSTMENTS, refer to the
“DV MECHANICAL ADJUSTMENT MANUAL I”
(9-973-815-11) and “DV MECHANICAL
ADJUSTMENT MANUAL III” (9-973-981-11).
“DV MECHANICAL ADJUSTMENT MANUAL I”
(9-973-815-11) and “DV MECHANICAL
ADJUSTMENT MANUAL III” (9-973-981-11).
Photo : DCR-SC100E
: RMT-808
DIGITAL VIDEO CAMERA RECORDER
NTSC : DCR-SC100
PAL
PAL
: DCR-SC100E
— Continued on next page —
DCR-SC100/SC100E
RMT-808/809
D200 MECHANISM
SPECIFICATIONS
• Tourist model of DCR-SC100E is the same as
E model of DCR-SC100E.
— 2 —
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit board Repairing
• Keep the temperature of the soldering iron around 270°C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer:
safety checks before releasing the set to the customer:
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK
! OR DOTTED LINE WITH
MARK
! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
! SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Table for difference of function
Model
Destination
Remote Commander
Color System
Lens
CCD imager
VTR REC
TV ON
DCR-SC100
US, Canadian
RMT-808
NTSC
10X
120X
ICX089AK
¬
¬
¬
DCR-SC100E
AEP, UK
RMT-809
PAL
10X
40X
ICX091AK
DCR-SC100E
E, Tourist
RMT-808
PAL
10X
120X
ICX091AK
¬
¬
¬
Optical
Digital
G
G
G
— 3 —
RMT-808
RMT-809
Supplied Accessories
2
!£
!¢
1
5
4
3
6
7
8
!¡
0
9
!™
1 Wireless Remote Commander (1)
RMT-808 ; DCR-SC100/DCR-SC100E : E
RMT-809 ; DCR-SC100E : AEP, UK
RMT-809 ; DCR-SC100E : AEP, UK
2 NP-F530 battery pack (1)
3 AC power adaptor (1)
AC-V615A
4 R6 (size AA) battery for remote Commander (2)
5 A/V connecting cable (1)
6 Shoulder strap (1)
7 21-pin adaptor (1)
DCR-SC100E : AEP, UK
8 Lens cap (1)
9 Sun shade (1)
0 DK-415 connecting cord (1)
!¡ 2-pin conversion adaptor (1)
DCR-SC100E : E
!™ 3-pin conversion plug adaptor (1)
DCR-SC100E : UK
!£ Step up ring (1)
!¢ String cap (1)
— 4 —
SERVICE NOTE
Battery terminal
‘
Battery switch
Battery terminal
’
Battery SIG terminal
1. POWER SUPPLY DURING REPAIRS
In this unit, about 25 seconds after power is supplied (8.4V) to the
battery terminal using the service power cord (J-6082-223-A), the
power is shut off so that the unit cannot operate.
This following two methods are available to prevent this. Take note
of which to use during repairs.
battery terminal using the service power cord (J-6082-223-A), the
power is shut off so that the unit cannot operate.
This following two methods are available to prevent this. Take note
of which to use during repairs.
Method 1.
Connect the servicing remote commander RM-95 (J-6082-053-B) to
the LANC jack, and set the remote commander switch to the “ADJ”
side.
the LANC jack, and set the remote commander switch to the “ADJ”
side.
Method 2.
Press the following battery switch using adhesive tape, etc.
2. HANDLING THE VC. MR BOARD
Never heat the VC and MR boards with hot air. (Malfunctions may
result.)
Also remove after dehumidifying.
result.)
Also remove after dehumidifying.
3. SPECIAL PRECAUTIONS ON DISCONNECTION
OF CONNECTOR ATTACHED TO THE FLEXIBLE
BOARD
BOARD
•
Apply force in the arrow direction and disconnect.
•
Do not apply force in the direction as this will cause the solder
(of the pin) to float easily.
(of the pin) to float easily.
•
When touching the pins with the solder iron, do not touch other
parts. (deformation may occur.)
parts. (deformation may occur.)
•
Ensure no folding lines are formed on the flexible board.
(This will cause the internal copper film to cut easily.)
(This will cause the internal copper film to cut easily.)
Flexible board
Connector
*
*
*
