Sony DCR-PJ5 / DCR-PJ5E / DCR-PJ6 / DCR-PJ6E (serv.man2) Service Manual ▷ View online
DCR-PJ5/PJ5E_L2
– 2 –
SPECIFICATIONS
System
Signal format: PAL color, CCIR standards
Movie recording format:
Movie recording format:
Video: MPEG-2 PS
Audio recording system:
Dolby Digital 2ch
Dolby Digital Stereo Creator
Photo file format
: DCF Ver.2.0 Compatible
: Exif Ver.2.21 Compatible
: MPF Baseline Compatible
Recording media (Movie/Photo)
“Memory Stick PRO Duo” media
SD memory card (Class 2 or faster)
When measuring media capacity, 1 GB equals
1 billion bytes, a portion of which is used for
system management and/or application files.
The capacity that a user can use is
approximately 79.3 GB.
1 billion bytes, a portion of which is used for
system management and/or application files.
The capacity that a user can use is
approximately 79.3 GB.
Image device
2.25 mm (1/8 type) CCD (Charge Coupled
Device)
Gross: Approx. 800 000 pixels
Effective (Movie, 16:9): Approx.
490 000 pixels
490 000 pixels
Effective (Photo, 16:9): Approx. 490 000 pixels
Effective (Photo, 4:3): Approx. 560 000 pixels
Lens
57 × (Optical), 67 × (Extended), 1 800 ×
(Digital)
(Digital)
F1.8 ~ F5.7
Focal
length:
f=1.8 mm ~ 102.6 mm (3/32 in. ~ 4 1/8 in.)
When converted to a 35 mm still camera
For movies: 39 mm ~ 2 223 mm
(1 9/16 in. ~ 87 5/8 in.) (16:9)
(1 9/16 in. ~ 87 5/8 in.) (16:9)
For photos: 44 mm ~ 2 508 mm
(1 3/4 in. ~ 98 3/4 in.) (4:3)
(1 3/4 in. ~ 98 3/4 in.) (4:3)
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K), [OUTDOOR]
(5 800 K)
Minimum illumination
3 lx (lux) ([AUTO SLW SHUTTR] is set to [ON],
3 lx (lux) ([AUTO SLW SHUTTR] is set to [ON],
shutter speed 1/25 second)
Input/Output connectors
A/V OUT jack: Video/audio output jack
USB jack: mini-AB (Output only)
USB jack: mini-AB (Output only)
LCD screen
Picture: 6.7 cm (2.7 type, aspect ratio 16:9)
Total number of pixels: 230 400 (960 × 240)
Total number of pixels: 230 400 (960 × 240)
Projector (DCR-PJ5E)
Projection type: DLP
Light source: LED (R/G/B)
Focus: Manual
Image size: 10 type ~ 60 type
Throw Distance: Approx. 0.5 m ~ 3.0 m
Light source: LED (R/G/B)
Focus: Manual
Image size: 10 type ~ 60 type
Throw Distance: Approx. 0.5 m ~ 3.0 m
(1.6 feet ~ 9.8 feet)
Color repeatability: Approx. 16 700 000
Brightness*: Max. 10 lumens
Contrast ratio: 1500:1
Resolution (output): nHD (640 × 360)
Continuous projection time (when using the
Brightness*: Max. 10 lumens
Contrast ratio: 1500:1
Resolution (output): nHD (640 × 360)
Continuous projection time (when using the
supplied battery pack): Approx. 1.0 h
* The specification of the brightness given here
is the average value for this camcorder at the
time of shipment and is indicated in the format
specified in JIS X 6911:2003 for data projectors.
The measurement method and conditions are
based on Appendix 2 of the standard.
is the average value for this camcorder at the
time of shipment and is indicated in the format
specified in JIS X 6911:2003 for data projectors.
The measurement method and conditions are
based on Appendix 2 of the standard.
General
Power requirements: DC 6.8 V/7.2 V (battery
pack) DC 8.4 V (AC Adaptor)
Average power consumption: During camera
recording, using LCD screen at normal
brightness:
Memory card: 1.9W
DCR-PJ5E:
1.9W
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to + 60 °C
(–4 °F to +140 °F)
Dimensions (approx.)
DCR-PJ5E:
DCR-PJ5E:
58.5 mm × 55.5 mm × 113.5 mm
(2 3/8 in. × 2 1/4 in. × 4 1/2 in.) (w/h/d)
including the projecting parts
(2 3/8 in. × 2 1/4 in. × 4 1/2 in.) (w/h/d)
including the projecting parts
58.5 mm × 55.5 mm × 124.5 mm
(2 3/8 in. × 2 1/4 in. × 5 in.) (w/h/d)
including the projecting parts, and the supplied
(2 3/8 in. × 2 1/4 in. × 5 in.) (w/h/d)
including the projecting parts, and the supplied
rechargeable battery pack attached
Mass (approx.)
DCR-PJ5E:
DCR-PJ5E:
230 g (8.0 oz) main unit only
270 g (9.0 oz) including the supplied
rechargeable battery pack and memory card
AC Adaptor AC-L200C/AC-L200D
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 0.35 A - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to + 60 °C
(–4 °F to +140 °F)
Dimensions (approx.): 48 mm × 29 mm × 81 mm
(1 15/16 in. × 1 3/16 in. × 3 1/4 in.) (w/h/d)
excluding the projecting parts
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
* See the label on the AC Adaptor for other
specifications.
specifications.
Rechargeable battery pack NP-FV30
Maximum output voltage: DC 8.4 V
Output voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.12 A
Capacity
Output voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.12 A
Capacity
typical: 3.6 Wh (500 mAh)
minimum: 3.6 Wh (500 mAh)
Type: Li-ion
Design and specifications of your camcorder and
accessories are subject to change without notice.
accessories are subject to change without notice.
●
Manufactured under license from Dolby
Laboratories.
Model information table
Model
DCR-PJ5
DCR-PJ5E
Destination
US,
CND, E, MX, BR, AR
AEP, UK, NE, E, AUS
Color system
NTSC
PAL
• Abbreviation
AR :
AR :
Argentine
model
AUS :
Australian
model
BR :
Brazilian
model
CND :
Canadian
model
MX :
Mexican
model
NE
: North European model
SPECIFICATIONS
System
Signal format: NTSC color, EIA standards
Movie recording format:
Movie recording format:
Video: MPEG-2 PS
Audio recording system:
Dolby Digital 2ch
Dolby Digital Stereo Creator
Photo file format
: DCF Ver.2.0 Compatible
: Exif Ver.2.21 Compatible
: MPF Baseline Compatible
Recording media (Movie/Photo)
“Memory Stick PRO Duo” media
SD memory card (Class 2 or faster)
When measuring media capacity, 1 GB equals
1 billion bytes, a portion of which is used for
system management and/or application files.
The capacity that a user can use is
approximately 79.3 GB.
1 billion bytes, a portion of which is used for
system management and/or application files.
The capacity that a user can use is
approximately 79.3 GB.
Image device
2.25 mm (1/8 type) CCD (Charge Coupled
Device)
Gross: Approx. 800 000 pixels
Effective (Movie, 16:9): Approx.
490 000 pixels
Effective (Photo, 16:9): Approx. 490 000 pixels
Effective (Photo, 4:3): Approx. 490 000 pixels
Lens
57 × (Optical), 67 × (Extended), 1 800 ×
(Digital)
F1.8 ~ F5.7
Focal
length:
f=1.8 mm ~ 102.6 mm (3/32 in. ~ 4 1/8 in.)
When converted to a 35 mm still camera
For movies: 39 mm ~ 2 223 mm
(1 9/16 in. ~ 87 5/8 in.) (16:9)
(1 9/16 in. ~ 87 5/8 in.) (16:9)
For photos: 44 mm ~ 2 508 mm
(1 3/4 in. ~ 98 3/4 in.) (4:3)
(1 3/4 in. ~ 98 3/4 in.) (4:3)
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K), [OUTDOOR]
(5 800 K)
Minimum illumination
3 lx (lux) ([AUTO SLW SHUTTR] is set to [ON],
3 lx (lux) ([AUTO SLW SHUTTR] is set to [ON],
shutter speed 1/30 second)
Input/Output connectors
A/V OUT jack: Video/audio output jack
USB jack: mini-AB
USB jack: mini-AB
LCD screen
Picture: 6.7 cm (2.7 type, aspect ratio 16:9)
Total number of pixels: 230 400 (960 × 240)
Total number of pixels: 230 400 (960 × 240)
Projector (DCR-PJ5)
Projection type: DLP
Light source: LED (R/G/B)
Focus: Manual
Image size: 10 type ~ 60 type
Throw Distance: Approx. 0.5 m ~ 3.0 m
Light source: LED (R/G/B)
Focus: Manual
Image size: 10 type ~ 60 type
Throw Distance: Approx. 0.5 m ~ 3.0 m
(1.6 feet ~ 9.8 feet)
Color repeatability: Approx. 16 700 000
Brightness*: Max. 10 lumens
Contrast ratio: 1500:1
Resolution (output): nHD (640 × 360)
Continuous projection time (when using the
Brightness*: Max. 10 lumens
Contrast ratio: 1500:1
Resolution (output): nHD (640 × 360)
Continuous projection time (when using the
supplied battery pack): Approx. 1.0 h
* The specification of the brightness given here
is the average value for this camcorder at the
time of shipment and is indicated in the format
specified in JIS X 6911:2003 for data projectors.
The measurement method and conditions are
based on Appendix 2 of the standard.
is the average value for this camcorder at the
time of shipment and is indicated in the format
specified in JIS X 6911:2003 for data projectors.
The measurement method and conditions are
based on Appendix 2 of the standard.
General
Power requirements: DC 6.8 V/7.2 V (battery
pack) DC 8.4 V (AC Adaptor)
Average power consumption: During camera
recording, using LCD screen at normal
brightness:
Memory card: 1.9W
DCR-PJ5:
1.9W
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to + 60 °C
(–4 °F to +140 °F)
Dimensions (approx.)
DCR-PJ5:
DCR-PJ5:
58.5 mm × 55.5 mm × 113.5 mm
(2 3/8 in. × 2 1/4 in. × 4 1/2 in.) (w/h/d)
including the projecting parts
(2 3/8 in. × 2 1/4 in. × 4 1/2 in.) (w/h/d)
including the projecting parts
58.5 mm × 55.5 mm × 124.5 mm
(2 3/8 in. × 2 1/4 in. × 5 in.) (w/h/d)
including the projecting parts, and the supplied
(2 3/8 in. × 2 1/4 in. × 5 in.) (w/h/d)
including the projecting parts, and the supplied
rechargeable battery pack attached
Mass (approx.)
DCR-PJ5:
DCR-PJ5:
230 g (8.0 oz) main unit only
270 g (9.0 oz) including the supplied
rechargeable battery pack and memory card
AC Adaptor AC-L200C/AC-L200D
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 0.35 A - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
Storage temperature: –20 °C to + 60 °C
(–4 °F to +140 °F)
Dimensions (approx.): 48 mm × 29 mm × 81 mm
(1 15/16 in. × 1 3/16 in. × 3 1/4 in.) (w/h/d)
excluding the projecting parts
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
* See the label on the AC Adaptor for other
specifications.
specifications.
Rechargeable battery pack NP-FV30
Maximum output voltage: DC 8.4 V
Output voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.12 A
Capacity
Output voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.12 A
Capacity
typical: 3.6 Wh (500 mAh)
minimum: 3.6 Wh (500 mAh)
Type: Li-ion
Design and specifications of your camcorder and
accessories are subject to change without notice.
accessories are subject to change without notice.
●
Manufactured under license from Dolby
Laboratories.
These specifications are extracted from instruction manual of
DCR-PJ5E.
DCR-PJ5E.
These specifications are extracted from instruction manual of
DCR-PJ5.
DCR-PJ5.
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2012.03
DCR-PJ5/PJ5E_L2
– 3 –
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
leaded solder and leaded solder will cause detachment phenomenon.
DCR-PJ5/PJ5E_L2
1-1
1. SERVICE NOTE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off
so that the unit cannot operate.
These following method is available to prevent this.
so that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor.
1-2. PRECAUTION ON REPLACING THE VC-648 BOARD
Turn on the set and establish a USB connection , save the USB serial data before replacing the board.
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
Start the Adjust Manual in the Adjust Station and execute the “DESTINATION DATA WRITE”.
After the board replacement, the error of the built-in recording media may be displayed.
In this case, execute the [DESTINATION DATA WRITE] then the error will be cleared.
If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
In this case, execute the [DESTINATION DATA WRITE] then the error will be cleared.
If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB SERIAL SAVE
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB SERIAL No. INPUT”.
1-3. SELF-DIAGNOSIS FUNCTION
1-3-1. Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis func-
tion starts working, and displays on the LCD screen what to do.
This function consists of two display; self-diagnosis display and service
mode display. Details of the self-diagnosis functions are provided in the
Instruction manual.
tion starts working, and displays on the LCD screen what to do.
This function consists of two display; self-diagnosis display and service
mode display. Details of the self-diagnosis functions are provided in the
Instruction manual.
1-3-2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the LCD
screen shows a 4-digit display consisting of an alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”of the
problem.
screen shows a 4-digit display consisting of an alphabet and numbers,
which blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”of the
problem.
1 1
3 1
C
Repaired by:
Refer to “1-3-3. Self-diagnosis Code Table” .
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
LCD screen
C : 3 1 : 1 1
1 1
3 1
C
Repaired by:
Refer to “1-3-3. Self-diagnosis Code Table” .
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
LCD screen
C : 3 1 : 1 1
DCR-PJ5/PJ5E_L2
1-2E
1-3-3. Self-diagnosis Code Table
Self-diagnosis Code
Symptom/State
Correction
Repaired by:
Block
Function
Detailed
Code
C
0
4
0
0
Non-standard battery is used.
Use the InfoLITHIUM battery.
C
0
6
0
0
The battery pack temperature is high.
Change the battery pack or replace it in a cool place.
C
1
3
0
1
Memory card is unformatted.
Memory card is broken.
Memory card is broken.
Format the Memory card.
Insert a new Memory card.
Insert a new Memory card.
C
1
3
0
2
Disc access error.
Remove the power source. Reconnect it again and operate your
camcorder again.
camcorder again.
E
2
0
0
0
Flash memory data are rewritten.
Make flash memory data correct value. (Note 1)
E
6
1
0
0
Difficult to adjust focus
(Cannot initialize focus).
(Cannot initialize focus).
Inspect the lens block focus reset sensor (pin 8 of CN5401 on the
VC-648 board) when focusing is performed when the focus button is
pressed in the focus manual mode, and the focus motor drive circuit
(IC5401 on the VC-648 board) when the focusing is not performed.
VC-648 board) when focusing is performed when the focus button is
pressed in the focus manual mode, and the focus motor drive circuit
(IC5401 on the VC-648 board) when the focusing is not performed.
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens).
(Cannot initialize zoom lens).
Inspect the lens block zoom reset sensor (pin 0 of CN5401 on the
VC-648 board) when zooming is performed when the zoom lever is
operated, or the zoom motor drive circuit (IC5401 on the VC-648
board) when zooming is not performed.
VC-648 board) when zooming is performed when the zoom lever is
operated, or the zoom motor drive circuit (IC5401 on the VC-648
board) when zooming is not performed.
E
6
1
1
1
The abnormalities in initialization of the focus
lens and the abnormalities in initialization of the
zoom lens occurred simultaneously.
lens and the abnormalities in initialization of the
zoom lens occurred simultaneously.
Check both E: 61: 00 and E: 61: 10 of the self-diagnosis code.
E
9
2
0
1
Battery current value goes over the max
discharge current.
discharge current.
Check the remaining battery power because this symptom may be
depended on the remaining battery level, and confirm whether or not
the symptom is occurred after replacing the battery. If the symptom
is still occurred, overhaul inspection is needed. Check each output of
DC-DC converter (IC4701) on the VC-648 board with the AC adaptor
connected to DC JACK (J901) on the VC-648 board. (the minimum
connection to periphery)
depended on the remaining battery level, and confirm whether or not
the symptom is occurred after replacing the battery. If the symptom
is still occurred, overhaul inspection is needed. Check each output of
DC-DC converter (IC4701) on the VC-648 board with the AC adaptor
connected to DC JACK (J901) on the VC-648 board. (the minimum
connection to periphery)
E
9
4
0
0
Fault of writing to or erasing the flash memory. Inspect the flash memory (IC7801 on the VC-648 board).
E
9
4
0
1
Internal flash memory fault.
Inspect the flash memory (IC7801 on the VC-648 board).
Note 1 : Start the Adjust Manual in the Adjust Station and refer to the “DESTINATION DATA WRITE”.