Sony DCR-PC8E (serv.man2) Service Manual ▷ View online
5-5
DCR-PC8E
Fig. 5-1-2.
1-1-2.
Preparations
Note 1:
For details of how remove the cabinet and boards, refer to “2.
DISASSEMBLY”.
DISASSEMBLY”.
Note 2:
When performing only the adjustments, the lens block and boards
need not be disassembled.
need not be disassembled.
1)
Connect the equipment for adjustments according to Fig. 5-1-2.
Note 3:
As removing the control switch block (FK-1770)(removing the
VC-265D board CN013) means removing the lithium 3V power
supply (BT601), data such as date, time, user-set menus will be
lost. After completing adjustments, reset these data. If the cabinet
(R) has been removed, the self-diagnosis data, data on history of
use (total drum rotation time etc. ) will be lost. Before removing,
note down the self-diagnosis data (data of page:2, address: B0 to
C6) and the data on history use (data of page: 2, address: A2 to
AA). (Refer to “SELF-DIAGNOSIS FUNCTION” for the self-
diagnosis data, and to “5-4.Service Mode” for the data on the
history use.)
VC-265D board CN013) means removing the lithium 3V power
supply (BT601), data such as date, time, user-set menus will be
lost. After completing adjustments, reset these data. If the cabinet
(R) has been removed, the self-diagnosis data, data on history of
use (total drum rotation time etc. ) will be lost. Before removing,
note down the self-diagnosis data (data of page:2, address: B0 to
C6) and the data on history use (data of page: 2, address: A2 to
AA). (Refer to “SELF-DIAGNOSIS FUNCTION” for the self-
diagnosis data, and to “5-4.Service Mode” for the data on the
history use.)
Note 4:
Setting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (PS-1770) removed. After
completing adjustments, be sure to exit the “Forced Camera Power
ON Mode”.
on with the control switch block (PS-1770) removed. After
completing adjustments, be sure to exit the “Forced Camera Power
ON Mode”.
Note 5:
Exiting the “Forced Camera Power ON” Mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
Front of the lens
1.5 m
Pattern box
5-6
DCR-PC8E
Fig. 5-1-3.
Vector scope
Must be connected when performing
the LCD system adjustments.
the LCD system adjustments.
Must be connected when
performing the video or
EVF system adjustments.
performing the video or
EVF system adjustments.
Must be connected
Must be connected
Cabinet (R)
Color monitor
VIDEO (Yellew)
LANC
jack
jack
AUDIO/VIDEO
jack
CN3351
CN3354
CN011
CN001
CN2105
CN2100
PD-148A
board
board
Inverter
transformer
unit
transformer
unit
CN2101
CN2104
CN2103
CN3018
CN3105
Note
Note
Note: If CN3105 of BJ-002A board is mistaken for CN3100, the charge system of the unit may break.
So ascertain the color of the connector when assembling these connectors.
CN3106
BJ-002A board
CN3107
DV jack
DC IN jack
AC power adaptor
(8.4 Vdc)
AC-L10, AC-VQ800 etc.
(8.4 Vdc)
AC-L10, AC-VQ800 etc.
CN3100
VC-265D board
CN004
CN013
CN012
CN3353
CF-085
board
board
CN009
CN3355
AUDIO L
(White)
(White)
AUDIO R
(Red)
(Red)
Adjustment
remote commander
remote commander
CPC-6 terminal board jig
(J-6082-371-A)
(J-6082-371-A)
CPC-jig for LCD panel
(J-6082-529-A)
(J-6082-529-A)
6
1
CPC-6 flexible jig
(J-6082-370-B)
(J-6082-370-B)
Terminated at 75
Ω
(White)
(Blue)
5-7
DCR-PC8E
1-1-3.
Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1.
POWER (PS-1770 block) ...................................... CAMERA
2.
NIGHT SHOT (Lens block) ............................................ OFF
3.
FUNCTION settings of the touch panel
DIGITAL EFFECT ..................................................... OFF
EXPOSURE ................................................................ OFF
MANUAL SET of the MENU settings
EXPOSURE ................................................................ OFF
MANUAL SET of the MENU settings
PROGRAM AE ................................................ AUTO
PICTURE EFFECT .............................................. OFF
WHITE BALANCE .......................................... AUTO
PICTURE EFFECT .............................................. OFF
WHITE BALANCE .......................................... AUTO
CAMERA SET of the MENU settings
DIGITAL ZOOM .................................................. OFF
16:9 WIDE ............................................................ OFF
STEADY SHOT ................................................... OFF
16:9 WIDE ............................................................ OFF
STEADY SHOT ................................................... OFF
SETUP MENU of the MENU settings
DEMO MODE ...................................................... OFF
4.
FOCUS (FK-1770 block) ............................................ Manual
5.
BACK LIGHT (FK-1770 block) ...................................... OFF
2. Order of Adjustments
Basically carry out adjustments in the order given.
Fig.5-1-4.
3. Subjects
1)
Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)
When performing adjustments using the color bar chart, adjust
the picture frame as shown in Fig. 5-1-4. (Color reproduction
adjustment frame)
2)
Clear chart (Color reproduction adjustment frame)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
Remove the color bar chart from the pattern box and insert a
clear chart in its place. (Do not perform zoom operations during
this time.)
3)
Flange back adjustment chart
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm
Make the chart shown in Fig. 5-1-5 using A0 size (1189mm
×
841mm) black and white vellum paper.
Fig. 5-1-5.
Note:
Use matte vellum paper bigger than A0, and make sure the edges of
the black and white paper joined together are not rough.
the black and white paper joined together are not rough.
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame )
Fig. a
(Video output terminal
output waveform)
Fig. b (TV monitor picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
obtain the output waveform shown in Fig. a
and the TV monitor display shown in Fig. b.
White
Black
841mm
1189mm
5-8
DCR-PC8E
1-2.
INITIALIZATION OF C, D, E, F, 7, 8 PAGE
DATA
DATA
1-2-1.
INITIALIZATION OF C, D, 8 PAGE DATA
1. Initializing the C, D, 8 Page Data
Note1: If “Initializing the C, D, 8 Page Data” is performed, all
data of the C page, D page and 8 page will be initialized.
(It is impossible to initialize a single page.)
(It is impossible to initialize a single page.)
Note2:
If the C, D, 8 page data has been initialized, the following
adjustments need to be performed again.
1) Modification of C, D, 8 page data
2) Serial No. input
3) Servo and RF system adjustments
4) Video system adjustments
5) Color viewfinder system adjustments
6) LCD system Adjustments
adjustments need to be performed again.
1) Modification of C, D, 8 page data
2) Serial No. input
3) Servo and RF system adjustments
4) Video system adjustments
5) Color viewfinder system adjustments
6) LCD system Adjustments
Adjusting page
C
Adjusting Address
10 to FF
Adjusting page
D
Adjusting Address
10 to FF
Adjusting page
8
Adjusting Address
00 to FF
Initializing Method:
Order Page Address Data
Procedure
1
0
01
01
Set the data
2
3
81
Check that the data is “00”.
3
3
80
0A
Set the data, and press the PAUSE
button.
button.
4
3
80
Check that the data changes to
“1A”
“1A”
5
Perform “Modification of C, D, 8
Page Data”.
Page Data”.
2. Modification of C, D, 8 Page Data
If the C, D, 8 page data has been initialized, change the data of the
“Fixed data-2” address shown in the following tables by manual
input.
“Fixed data-2” address shown in the following tables by manual
input.
Modifying Method:
1)
1)
Before changing the data, select page: 0, address: 01, and set
data: 01.
data: 01.
2)
New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
they are different in destination. When changing the data, copy
the data built in the same model.
Note:
If copy the data built in the different model, the camcorder may
not operate.
not operate.
3)
When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
4)
Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
If not, change the data to the initial value.
Processing after Completing Modification of C, D, 8 Page data
Order Page Address Data
Procedure
1
2
00
29
Set the data
2
2
01
29
Set the data, and press the PAUSE
button.
button.
Note:
If the following symptoms occur after completing of the
“Modification of C, D, 8 page data”, check that the data of the “Fixed
data-2” addresses of D page are same as those of the same model of
the same destination.
1) The battery end mark on the LCD or viewfinder screen is flashing.
2) The power is shut off so that unit cannot operate.
“Modification of C, D, 8 page data”, check that the data of the “Fixed
data-2” addresses of D page are same as those of the same model of
the same destination.
1) The battery end mark on the LCD or viewfinder screen is flashing.
2) The power is shut off so that unit cannot operate.
3. C Page Table
Note:
Fixed data-1: Initialized data. (Refer to “1. Initializing the C, D, 8
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8
Page Data”.)
Page Data”.)
Fixed data-2: Modified data. (Refer to “2. Modification of C, D, 8
Page Data”.)
00 to 0F
10
11
12
13
14 to 15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23 to 24
25
26
27
28
29
2A to 2B
2C
2D to 46
47
48 to 4B
4C
4D
4E to 4F
50
51
52 to 68
69
6A to 6F
EE
00
00
00
E0
2A
2A
32
32
25
3E
3E
DC
99
88
E3
A1
04
20
03
Switching position adj.
Fixed data-1
Cap FG duty adj.
Fixed data-2
AEQ adj.
Fixed data-1
AEQ adj.
Fixed data-1
AGC center level adj.
PLL fo adj.
APC adj.
LPF fo adj.
Fixed data-1
S VIDEO out Y level adj.
S VIDEO out Cr level adj.
S VIDEO out Cb level adj.
Chroma BPF fo adj.
PLL fo fine adj.
Fixed data-1
APC adj.
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Fixed data-2
Fixed data-1
Address
Remark
Initial value
Click on the first or last page to see other DCR-PC8E (serv.man2) service manuals if exist.