Sony DCR-PC115E / DCR-PC120E Service Manual ▷ View online
— 10 —
DCR-PC115E/PC120E
2.
DISASSEMBLY
The following flow chart shows the disassembly procedure.
DCR-PC115E/PC120E
2-10. Cabinet (G) block assembly, etc
2-11. Control switch block (FK-1850)
2-12. Control switch block (PS-1850)
2-13. Blind plate assembly
2-14. PD-148B board,
Inverter transformer unit
Inverter transformer unit
2-15. Hinge assembly
2-9. Flash unit (ST)
2-7. Mechanism deck
2-8. Flash unit (MC)
2-3. FJ-035 board
2-6. VC-270 board
2-4. VM-027 board
2-5. CD-349P board, Lens device
2-2. VTR complete, Cabinet (R) section
2-1. Cabinet (L) section
— 11 —
DCR-PC115E/PC120E
Attach the BT cable so
that it stretches straight
downward.
that it stretches straight
downward.
A
B
1
Pass the cable through the hole
A
of the
Cabinet (R) section.
2
Draw the cable through clearance of the flexible
board of the FJ-035 board and route it under the
flexible board of the FJ-035 board.
flexible board of the FJ-035 board.
3
Route the cable under the rigid portion of the
FJ-035 board.
4
Insert it into the notch of the lens rubber (R).
5
Insert it into the notch of the BT cable sheet.
6
Route the cable through the clearance
B
.
7
Insert it to the connector on the BT-003 board.
[Routing the Bluetooth BT cable] (PC120E)
BT cable
BT cable
BT cable
BT cable
guide
guide
Lens
rubber (R)
rubber (R)
BT cable
sheet
sheet
BT-003 board
BT cable
Rigid portion of the
FJ-035 board
FJ-035 board
Flexible board of
the FJ-035 board
the FJ-035 board
Route the cable through the
clearance
clearance
B
, and then hook
it on the clearance between
the BT cable guide and
lens device.
the BT cable guide and
lens device.
BT cable
BT cable
guide
guide
Lens device
BT-003
board
board
Connector of
BT cable
BT cable
When removing the BT cable
from the BT-003 board, be sure
to hold the connector of the
BT-003 cable and remove it.
from the BT-003 board, be sure
to hold the connector of the
BT-003 cable and remove it.
— 12 —
DCR-PC115E/PC120E
2-1.
CABINET (L) SECTION
NOTE: Follow the disassembly procedure in the numerical order given.
ON
OFF
When installing the Cabinet (L) section to the Cabinet (R) section
and to the VTR complete, install it while the "Night-Shot switch
outside the Cabinet (L) section" and "Night-Shot switch on top of
the Lens Device" are facing upward.
and to the VTR complete, install it while the "Night-Shot switch
outside the Cabinet (L) section" and "Night-Shot switch on top of
the Lens Device" are facing upward.
1
Screw
(M1.7
×
2.5),
lock ace, p2
3
HS
Cabinet
2
Two claws
4
Three screws
(M1.7
×
2.5),
lock ace, p2
5
Jack ornamental
cover assembly
Jack ornamental
cover assembly
cover assembly
Lens Device
Night-Shot switch on top of
the Lens Device
the Lens Device
Night-Shot switch outside the
Cabinet (L) section
Cabinet (L) section
3
Two screws
(M1.7
×
4),
lock ace, p2
2
Two screws
(M1.7
×
2.5),
lock ace, p2
4
Screw
(M1.7
×
2.5),
lock ace, p2
1
Screw
(M1.7
×
2.5),
lock ace, p2
6
Cabinet (R) section,
VTR complete
5
Control switch block
(FK-1850) (51P)
(Caution:
High voltage)
High voltage)
Flash unit (MC)
7
Cabinet (L) section
Note: The power capacitor (C2010) of the flash unit is charged to the high tension voltage as high as 300 V at a maximum.
You will get electrical shock when you touch the Flash unit (MC) mounted with the terminal of the charged capacitor.
The charged potential remains even after the main power of the machine is turned off.
Discharge the remaining power in the capacitor referring to Service Note (page 6).
The charged potential remains even after the main power of the machine is turned off.
Discharge the remaining power in the capacitor referring to Service Note (page 6).
PRECAUTION DURING CABINET (L) SECTION
INSTALLATION
INSTALLATION
PRECAUTION DURING
JACK ORNAMENTAL COVER
ASSEMBLY INSTALLATION
JACK ORNAMENTAL COVER
ASSEMBLY INSTALLATION
IR window
assembly
assembly
OK
NG
Be careful that top of the Jack
ornamental cover assembly does not
hang over the IR window assembly.
ornamental cover assembly does not
hang over the IR window assembly.
— 13 —
DCR-PC115E/PC120E
2-2.
VTR COMPLETE, CABINET (R) SECTION
Routing of the flexible board of the
Operation Flash unit (ST) when
attaching the Cabinet (L) section.
Operation Flash unit (ST) when
attaching the Cabinet (L) section.
Routing of the flexible board of the
Operation FP-383 flexible board when
attaching the Cabinet (L) section.
Operation FP-383 flexible board when
attaching the Cabinet (L) section.
6
Flash unit (ST) (33P)
5
Microphone unit (5P)
4
FP-385 flexible
board (27P)
2
CPC lid
1
Screw
(M1.7
×
2.5),
lock ace, k3
3
FJ-035 board (88P)
3
FP-383 flexible board
(15P)
4
Cabinet (R) section
1
Screw
(M1.7
×
2.5),
lock ace, p2
5
VTR complete
2
Two screws
(M1.7
×
2.5),
lock ace, p2
1
Antenna (2.4GHz)
(PC120E)
See to "Routing the
Bluetooth BT cable" when
re-assembling parts
See to "Routing the
Bluetooth BT cable" when
re-assembling parts
3
BT-003 board
(PC120E)
4
FK flexible guard
2
Two screws
(M1.4
×
2),
lock ace
(PC120E)
(PC120E)
BT-003
board
board
Connector of
BT cable
BT cable
When removing the BT cable
from the BT-003 board, be sure
to hold the connector of the
BT-003 cable and remove it.
from the BT-003 board, be sure
to hold the connector of the
BT-003 cable and remove it.
Click on the first or last page to see other DCR-PC115E / DCR-PC120E service manuals if exist.