Sony DCR-PC106E / DCR-PC107E (serv.man2) Service Manual ▷ View online
1-1
SECTION 1
SERVICE NOTE
DCR-PC106E/PC107E
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
1-1. SERVICE NOTE
1.
NOTE FOR REPAIR
1-2E
DCR-PC106E/PC107E
2.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.
Use the AC power adaptor.
Use the AC power adaptor.
Method 2.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
3.
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1
Remove the front panel section and cabinet (R) section.
2
Remove the cabinet (upper) (G) assembly.
3
Remove the lens section.
4
Remove the rear panel assembly and control switch block (SS6800).
5
Remove the EVF section.
6
Open the VC-350 board.
7
Remove the mechanism deck and the VC-350 board.
8
Disconnect CN9002 (27P, 0.3mm) of VC-350 board.
9
Supply +4.5V from the DC power supply to the loading motor and unload with pressing the cassette compartment.
VC-350
CN9002
VC-350 board
DC power supply (+4.5Vdc)
Loading motor
Disconnect the flexible board from
CN9002 of VC-350 board.
CN9002 of VC-350 board.
DCR-PC106E/PC107E
2-1
2-2
2-1. DISASSEMBLY
The following flow chart shows the disassembly procedure.
SECTION 2
DISASSEMBLY
VC-350
VC-350
1
2
3
4
5
6
8
7
1
Two screws (M1.7x4) silver
2
Open the cassette lid.
3
Screw (M1.7x2.5) silver
4
Screw (M1.7x4) silver
1
Four screws (M1.7x2.5) silver
2
Eject knob
3
Two tapping screws (M1.7x3.5) black
4
Cabinet (G) section
3
1
2
4
1
1
5
6
7 qs
qd
qg
8
9
q;
qa
3
2
1
Screw (M1.7x4) silver
2
Rear panel assembly
3
Screw (M1.7x2.5) silver
4
Control key block (SS6800) (18P)
5
Control key block (SS6800)
6
FP-842 flexible board (20P)
7
FP-843 flexible board (39P)
8
Screw (M1.7x4) silver
9
Tapping screw (M1.7x3.5) black
q;
Two screws (M1.7x4) silver
qa
EVF section
4
3
2
5
4
1
1
Screw (M1.7x4) silver
2
Rear panel assembly
3
CR insulating sheet
4
Screw (M1.7x2.5) silver
5
to qf (CN9301 (20P), CN1001 (18P), CN1005 (20P), CN3001 (14P),
CN9002 (27P), CN9003 (27P), CN3101 (23P), CN1008 (39P),
CN9001 (10P),CN6501 (10P)) of VC-350 board.
qg
VC-350 board
5
Claw
6
FP-840 board (16P)
7
Harness (RR-057) (2P)
8
Front panel assembly (N)
1
Tape (A)
2
FP-844 flexible board (20P)
3
Screw (M1.7x2.5) silver
4
Return the VC-350 board.
9
1
q;
3
5
8
6
2
7
qa
4
1
Screw (M1.7
×
2.5) silver
2
Four claws
3
Hinge cover (M), FP-926 flexible board
4
Hinge cover (C)
5
FP-848 flexible board,
Hinge (63) assembly
HELP 03
HELP 01
HELP 02
1
2
5
3
4
1
4
2
3
1
Control key block (SB6800) (6P)
2
Tapping screw (M1.7x5) black
3
Two claws
4
TP cushion
5
P cabinet (M) assembly
6
PD-213 board,
LCD unit (ACX528AKP-J),
Light guide plate block
5
6
qf
1
Screw (M1.7x2.5) silver
2
Two screws (M1.7x4) silver
3
Two screws (M1.7x4) silver
4
Screw (M1.7x4) silver
5
FP-841 flexible board (26P)
1
9
2
3
4
7 8
q;
6
BT flexible adhesive sheet
7
FP-848 flexible board (22P)
8
FP-926 flexible board (6P)
9
FP-846 flexible board (51P)
q;
Cabinet (R) section
5
6
2
3
4
8
6
7
9
q;
qa
1
1
Tape (A)
2
Three tapping screws (M1.7x5) black
3
Hinge blind
4
Two screws (M1.7x3) black
5
Tapping screw (M1.7x3.5) black
6
P cabinet (C) (N) assembly
7
Tape (A)
8
FP-848 flexible board (22P)
9
Screw (M1.7x2.5) black
q;
LCD panel section
qa
Hinge section
5
3
5
7
q;
8
4
1
2
1
Two screws (M2x2.5) silver
2
Accessory shoe
3
Microphone unit (960H) (6P)
4
Screw (M1.7x2.5) silver
5
Cabinet (upper) (N) assembly
6
CR insulating sheet
7
Flexible board (from lens device) (23P)
8
FP-838 flexible board (14P)
9
Screw (M1.7x2.5) silver
q;
Screw (M1.7x2.5) silver
qa
Lens block assembly
9
6
qa
7
5
Four screws (M1.4x1.5) silver
6
Open the cassette lid.
7
VC-350 board, Mechanism deck.
6
1
Release the lock
2
Screw (M1.7x2.5) silver
3
Tapping screw (M1.7x3.5) black
1
4
5 3
6
2
4
Belt shaft
5
Belt bracket (front)
6
Grip belt assembly
2
3
1
2
1
Screw (M1.7x3) black
2
Tapping screw (M1.7x3.5) black
3
P cabinet (C) (N) assembly
1
1
Two screws (M1.4x2) black
2
Eye cup assembly
3
Two screws (M2x2.5) silver
4
Accessory shoe
3
4
DCR-PC106E/PC107E
2. DISASSEMBLY
2. DISASSEMBLY
2-3
2-4
2-2. SERVICE POSITION
VC-350
VC-350
AC power
adaptor
adaptor
AC IN
1
8
[SERVICE POSITION TO CHECK THE VTR SECTION]
Connection to Check the VTR Section
To check the VTR section, set the VTR to the "Forced VTR power ON" mode.
Operate the VTR functions using the touch panel. (When the control switch block (ZM6800) is removed, the function
buttons of the adjustment remote commander are not effective even if the HOLD switch of the adjustment remote
commander is set to the OFF position.)
Connection to Check the VTR Section
To check the VTR section, set the VTR to the "Forced VTR power ON" mode.
Operate the VTR functions using the touch panel. (When the control switch block (ZM6800) is removed, the function
buttons of the adjustment remote commander are not effective even if the HOLD switch of the adjustment remote
commander is set to the OFF position.)
Setting the "Forced VTR Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
To eject a cassette, connect the
control key block (SS6800)(18P)
control key block (SS6800)(18P)
Exiting the "Forced VTR Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
Adjustment remote
commander (RM-95)
commander (RM-95)
Cabinet (R) section
FP-848 Flexible
board (22P)
board (22P)
FP-843 Flexible
board (39P)
board (39P)
FP-841 Flexible
board (26P)
board (26P)
CN9003
CN6501
CN1008
CN1001
CN1007
CN2001
VC-350 board
Mechanism deck
Battery terminal board,
FP-841 flexible board
FP-841 flexible board
LANC
DC-IN
I/F unit for LANC control
(J-6082-521-A)
(J-6082-521-A)
CPC-15
(J-6082-564-A)
(J-6082-564-A)
1
2
3
4
5
6
8
7
2
1
3
3
2
5
4
1
3
5
7
q;
8
4
1
2
9
6
qa
9
1
q;
3
5
8
6
2
7
qa
4
CN1006
CN9002
CN9001
1
4
q;
2
5
6
9
8
7
3
7
6
1
9
2
3
4
7 8
q;
5
6
Click on the first or last page to see other DCR-PC106E / DCR-PC107E (serv.man2) service manuals if exist.