DOWNLOAD Sony DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E (serv.man8) Service Manual ↓ Size: 61.31 KB | Pages: 4 in PDF or view online for FREE

Model
DCR-PC103E DCR-PC104E DCR-PC105 DCR-PC105E (serv.man8)
Pages
4 Few pages! See other manuals at the bottom of the first or last page.
Size
61.31 KB
Type
PDF
Document
Service Manual
Brand
Device
Movie / CORRECTION-1 LEVEL 2
File
dcr-pc103e-dcr-pc104e-dcr-pc105-dcr-pc105e-sm8.pdf
Date

Sony DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E (serv.man8) Service Manual ▷ View online

SERVICE MANUAL
CORRECTION-1
Correct your service manual as shown below.
LEVEL
 
2
DCR-PC103E/PC104E/
PC105/PC105E
RMT-830/RMT-831
US Model
Canadian Model
Korea Model
DCR-PC105
AEP Model
UK Model
East European Model
DCR-PC103E/PC105E
E Model
Hong Kong Model
DCR-PC104E/PC105/PC105E
Chinese Model
DCR-PC104E/PC105E
Australian Model
DCR-PC105E
Tourist Model
DCR-PC105/PC105E
Ver 1.1  2003. 06
Correction of service note and printed wiring boards
— 2 —
DCR-PC103E/PC104E/PC105/PC105E
1-1. SERVICE NOTE
1.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.
Use the AC power adaptor (AC-L10, AC-VQ800 etc.).
Method 2.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
2.
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1
Only for DCR-PC105/PC105E, open the flash.
2
Only for DCR-PC105/PC105E, refer to “3. DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR” to discharge
the flash power supply capacitor.
3
Refer to page 2-3, 2-4 to remove the cabinet (front) assembly, cabinet (G) assembly and cabinet (L).
4
Refer to page 2-5 to remove the cabinet (R) section.
5
Refer to page 2-11, 2-14 to remove the cabinet (rear), control switch block (PS4400).
6
Refer to page 2-12, 2-13 to remove the ST-084 board and LENS/EVF/ST section.
7
Refer to page 2-22, 2-23 to remove the VC-319 board and mechanism deck (Z100).
8
Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
3.
HOW TO OPEN THE FLASH WHEN THE FLASH DOSEN’T OPEN (DCR-PC105/PC105E)
1
Refer to page 2-3, 2-4 to remove cabinet (G) assembly and cabinet (L).
2
Push the part pointed out with the arrow in the direction of the arrow.
DC power supply (+4.5Vdc)
Loading motor
SECTION 1
SERVICE NOTE
Note:
Exchange page 1-1 and page1-2 of Service Manual with page 2 and
page 3 of this Correction-1.
— 3 —
DCR-PC103E/PC104E/PC105/PC105E
4.
DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR (DCR-PC105/PC105E)
The power supply capacitor (C6606) of the ST-084 board is charged up to the maximum 300V potential.
There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged
voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be
discharged as described below.
4-1.
PREPARING THE SHORT JIG
To preparing the short jig. a small clip is attached to each end of a resistor of 1k
/1W (1-215-869-119)
Wrap insulating tape fully around the reads of the resistor to prevent electric shock.
4-2.
DISCHARGING THE CAPACITOR (DCR-PC105/PC105E)
1 k
/1 W
Wrap insulating tape.
A
K
Xenon tube
Accessory shoe GND
Short jig
ST-084 board TP6600
Accessory
shoe GND
C6606
Short jig
Discharging method (1):
1
Open the flash.
2
Remove the power supply (Battery or AC power adaptor).
3
Remove the ST cabinet (Upper).
4
Short-circuit between the Xenon tube anode and the GND
(GND of the accessory shoe) with the short jig about 10 seconds.
Discharging method (2):
1
Remove the power supply (Battery or AC power adaptor).
2
Refer to page 2-3 to remove the cabinet (front) section.
3
Refer to page 2-5 to release the cassette cover lock and remove
the cabinet (R) section.
4
Short-circuit between the TP6600 of the ST-084 board and the
GND (GND of the accessory shoe) with the short jig about 10
seconds.
— 4 —
DCR-PC103E/PC104E/PC105/PC105E
Sony EMCS Co.
2003F1600-1
  ©2003.6
Published by DI CS Strategy Div.
9-876-258-92
Page
Supplied contents
4-65
4-3. PRINTED WIRING BOARDS
LI-070 (BATTERY) PRINTED WIRING BOARD
NS-018 (SIRCS,NS) PRINTED WIRING BOARD
4-66
LI-070 BOARD(SIDE B)
NS-018 BOARD(SIDE B)
Display

Sony DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E (serv.man8) Service Manual ▷ Download

  • DOWNLOAD Sony DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E (serv.man8) Service Manual ↓ Size: 61.31 KB | Pages: 4 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E (serv.man8) in PDF for free, which will help you to disassemble, recover, fix and repair Sony DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E (serv.man8) Movie. Information contained in Sony DCR-PC103E / DCR-PC104E / DCR-PC105 / DCR-PC105E (serv.man8) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.