Sony DCR-PC10 / DCR-PC10E Service Manual ▷ View online
2-5
2-8. DD-103 BOARD
2
Battery terminal board
4
Three screws
(M2
×
6)
1
Screw
(M1.7
×
3)
3
Two screws
(M1.7
×
3)
Cabinet (bottom) assembly
6
DD-103 board
2-9. PD-97 BOARD, ND5500, LCD901
8
Connector
(From VC-199 board CN1001)
!¡
Two screws (M1.7
×
2.5)
7
Connector
(From VC-199 board CN1002)
9
LCD901
flexible board
5
FP-484 flexible board
!º
LCD901 LCD module
4
LCD case (L) assembly
2
Three screws
(M1.7
×
2.5)
3
Screw (M1.7
×
2.5)
6
Plate (3), PD ground
!£
ND5500
Cold cathode fluorescent tube
!™
PD-97 board
1
PD-97
BOARD
2-6
2-10.SERVICE POSITION-1
(MAINLY FOR VIDEO/AUDIO SYSTEM CHECKS OR ADJUSTMENTS)
Note: Do not apply excessive force to the flexible portion of DD-
103 board because of its shortness.
MR-39: CN3100
↔
Capstan motor flexible board
extension cable (18P)
(J-6082-374-A)
(J-6082-374-A)
MR-39 board
CPC terminal extension flexible board
(CPC-6 jig) (J-6082-370-A)
VC-199: CN6202
(CPC-6 jig) (J-6082-370-A)
VC-199: CN6202
CPC-6 terminal board jig
(J-6082-371-A)
(J-6082-371-A)
FK-4850
(Control switch block)
(Control switch block)
VC-199 board
DD-103 board
I/O board-1 jig
(J-6082-372-C)
DD-103: 26-pin MULTI connector
(J-6082-372-C)
DD-103: 26-pin MULTI connector
Regulated dc power supply
(8.4V)
VIDEO AUDIO OUT/
HEADPHONES jack
HEADPHONES jack
1
Remove each board in the disassembly procedure.
2
Connect the specified jigs as shown in the figure.
(Some connectors can be connected reversely by its shape.
So, note that its connection on removal.)
(Some connectors can be connected reversely by its shape.
So, note that its connection on removal.)
2-7
2-11.SERVICE POSITION-2
(MAINLY FOR CAMERA SYSTEM CHECKS OR ADJUSTMENTS)
Note: Do not apply excessive force to the flexible portion of DD-
103 board because of its shortness.
MR-39 board
CPC terminal extension flexible board
(CPC-6 jig) (J-6082-370-A)
VC-199: CN6202
(CPC-6 jig) (J-6082-370-A)
VC-199: CN6202
VC-199 board
DD-103 board
CPC-6 terminal board jig
(J-6082-371-A)
(J-6082-371-A)
Box or pedestal
Zoom lens
Mechanism deck block
Battery terminal
board
board
Battery terminal
FK-4850
(Control switch block)
(Control switch block)
’
‘
Regulated power supply
(8.4 V)
1
Remove each board in the disassembly procedure.
2
Connect the specified jigs as shown in the figure.
(Some connectors can be connected reversely by its shape.
So, note that its connection on removal.)
(Some connectors can be connected reversely by its shape.
So, note that its connection on removal.)
2-8E
2-12.CIRCUIT BOARDS LOCATION
MR-39
(REC/PB AMP, SERVO)
(REC/PB AMP, SERVO)
DD-103
(POWER SUPPLY, I/O)
(POWER SUPPLY, I/O)
CD-175 (CCD IMAGER)
PD-97 LCD RGB DRIVER,
TIMING GENERATOR,
LCD BACKLIGHT
LCD BACKLIGHT
CC-100
(TRANSLATION)
(TRANSLATION)
VF-117 (EVF)
VC-199
CAMERA, LENS DRIVE,
I/O, BLOCKING, ECC, TBC,
CHCD, AUDIO, DV I/O,
IR TRANSMITTER,
RGB DECODER,
MODE CONTROL
I/O, BLOCKING, ECC, TBC,
CHCD, AUDIO, DV I/O,
IR TRANSMITTER,
RGB DECODER,
MODE CONTROL
Click on the first or last page to see other DCR-PC10 / DCR-PC10E service manuals if exist.