Sony DCR-PC1 / DCR-PC1E Service Manual ▷ View online
1-30E
2-1
DCR-PC1/PC1E
SECTION 2
DISASSEMBLY
NOTE: Follow the disassembly procedure in the numerical order given.
The following flow chart shows the disassembly procedure.
2-1. CABINET (L) ASSEMBLY, CABINET (R) ASSEMBLY
VC
-2
10
Bo
ard
DD-111
Board
@§
Cabinet (L) assembly
(Refer to sec. 2-2.)
@∞
Cabinet (R) assembly
(Refer to sec. 2-5.)
@º
Control switch block
(ME-4780)
(VC-210 board CN2202)
(VC-210 board CN2202)
@¢
Remote control
window assembly
@™
Harness
(PD-107)
(VC-210 board CN2908)
(VC-210 board CN2908)
@£
Harness (PR-61)
(VC-210 board CN2201)
5
Harness (LI-58)
(MR-40 board CN2507)
!º
Open the LCD and
remove the screw.
(0-No. +P2 M1.7)
(0-No. +P2 M1.7)
!¡
Hinge cover
!§
Two screws
(0-No. +P2 M1.7)
!™
Open the
DV jack
cover
assembly.
cover
assembly.
!∞
Screw (0-No. +P2 M1.7)
!¶
Two screws
(0-No. +P2 M1.7)
4
Two screws
(+K M2
×
3.5 with 3 locks)
1
Two screws
(+K M2
×
3.5 with 3 locks)
!ª
Two screws
(0-No. +P2 M1.7)
!ª
Two screws
(0-No. +P2 M1.7)
!•
Open the cassette
lid by sliding the
EJECT knob in the
direction of the arrow.
EJECT knob in the
direction of the arrow.
9
Secondary
lithium batteries
(2 pcs)
(2 pcs)
6
Tripod screw
8
Remove the
two solderings.
7
FP-36 flexible
board
2
Accessory shoe
3
Shoe plate
!£
Two screws
(0-No. +P2 M1.7)
The FP-36 flexible
board is attached
on the tripod screw
by both sided
adhesive tape.
board is attached
on the tripod screw
by both sided
adhesive tape.
Remove
the claw.
the claw.
!¢
Remove the claw of the jack ornamental
plate and remove it in the direction shown by the arrow.
@¡
Harness (SP-158)
(DD-111 board CN9900)
The cabinet
(L) when viewed
from the bottom.
(L) when viewed
from the bottom.
2-1. CABINET (L) ASSEMBLY, CABINET (R) ASSEMBLY
1
-
7
DD-111 board,
Battery terminal
8
-
!•
MR-40 board
!ª
,
@º
VC-210 board
@¡
-
@∞
MD block
1
-
6
MD block assembly
7
,
8
EVF assembly
9
-
!£
Microrophone unit
1
-
8
Grip belt
9
-
!ª
Control switch block
@º
-
#º
Cabinet (G)
1
VF lens assembly
2
-
6
CD-203 board
7
-
!¡
Lens device
1
-
@¡
PD-102 board
1
-
6
,
@™
-
@•
LCD hinge assembly
@ª
-
#™
Speaker
#£
DV jack cover
#¢
,
#∞
S-terminal cover assembly
#§
Control switch block
(ME-4780)
(ME-4780)
1
-
!£
VF-125 board
#¶
-
$¡
LCD block
DCR-PC1
2-2.
2-3.
2-4.
2-4.
2-6.
2-6.
2-7.
2-5.
2-5.
2-5.
2-5.
2-5.
2-5.
2-5.
2-2
2-2. CABINET (L) ASSEMBLY, EVF, MD BLOCK ASSEMBLY
VC-210
DD-111
Board
MR-40 Board
Board
9
Pan head small screw
(0-No. special M2
×
4)
5
Connector
VC-210 board CN2001
2
Screw (0-No. +P2 M1.7)
3
VF-125 board (VC-210 board CN5000)
4
CD-203 board (VC-210 board CN201)
1
Control switch block (FX-4780)
(VC-210 board CN2910)
8
Remove the screw.
(0-No. +P2 M1.7)
7
Move in the direction of
the arrow
a
.
!£
Microphone case assembly
6
MD block assembly
(Refer to sec. 2-3)
!™
Microphone unit
!¡
Microphone GEL sheet
!º
Microphone
retainer plate
a
2-3. VC-210 BOARD, DC-111 BOARD, MF-40 BOARD
VC
-21
0
Boa
rd
D
D
-1
1
1
M
R
-40 Board
B
o
a
rd
D
D
-1
1
1
@∞
Two screws (Special head, small screw M1.7
×
3.5)
@¡
Two screws
(0-No. +P2 M1.7)
6
Two screws
(0-No. +P2 M1.7)
!ª
Two screws
(0-No. +P2 M1.7)
7
Two screws
(0-No. +P2 M1.7)
5
Battery plate
4
Battery terminal board
!™
Peel adhesive
tape off.
!¡
Peel off the
adhesive tape
(black).
(black).
!¢
Flexible board CN2505
(from mode switch)
!£
Flexible board CN2501
(from capstan motor)
!¶
Flexible board CN1810
(from video head)
!•
FP-586 flexible board CN2504
(from loading motor)
!∞
Flexible board CN2503
(from drum motor)
2
Remove the three solderings from the battery terminal.
@£
Stepped screws (3 pcs)
@§
Cassette compartment cover assembly
@¶
MD block
@¢
MD frame
@™
VC-210 board
!º
Connector
(VC-210 board CN2908)
1
Connector
(DD-111 board CN3200)
8
DD-111 board
3
TB-37
board
@º
MR-40 board
9
Connector
(VC-210 board CN2909)
!§
Flexible board CN2503
(from drum motor)
2-3
2-4. CONTROL SWITCH BLOCK
a
a
2
Remove an end of the grip belt.
9
Remove the area that is adhered, shown by hatching.
!•
Remove the area
that is adhered,
shown by hatching.
shown by hatching.
@¢
Cassette compartment window
Be sure to disengage the catch.
Be sure to disengage the catch.
Control switch block
Slant here in the direction of the
arrow
arrow
a
and remove it in the
direction of the arrow
b
.
1
Screw (0-No. +P2 M2.0)
4
Grip belt
7
Strap bracket
8
Bracket cap
5
Bracket cover
6
Belt bracket
!º
Two screws
(0-No. +P2 M1.7)
!£
Screw (0-No. +P2 M1.7)
!£
Three screws
(0-No. +P2 M1.7)
!™
Screw
(0-No. +P2 M1.7)
!£
Two screws (0-No. +P2 M1.7)
!¶
Two screws (0-No. +P2 M1.7)
@§
Two screws (0-No. +P2 M1.7)
@•
Two screws (0-No. +P2 M1.7)
@§
Screw (0-No. +P2 M1.7)
@¶
Lock board
#º
Cabinet (G)
#¡
Cabinet (L)
Cabinet (L) assembly
!§
Close the door of the grip lock
assembly once and remove the
control switch that is attached
to the cabinet (L), from the
cabinet (L) as shown.
control switch that is attached
to the cabinet (L), from the
cabinet (L) as shown.
@™
G lock slider
!ª
Control switch
block (FK-4780)
@º
FADER
button
!∞
Metal sheet nut
@£
EJECT knob
b
a
d
c
!¡
!¢
Remove the
claws.
@¡
Remove
the claws.
@ª
Remove the claws.
Be careful that the flexible
board is not caught.
board is not caught.
@∞
3
Two screws
(0-No. +P2 M2)
Click on the first or last page to see other DCR-PC1 / DCR-PC1E service manuals if exist.