Sony DCR-HC94E / DCR-HC96 / DCR-HC96E (serv.man4) Service Manual ▷ View online
6-4
DCR-HC94E/HC96/HC96E_ADJ
• Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
Table 6-1-1 (2)
Adjustment Section
Adjustment
(COMPLETE)
(COMPLETE)
(COMPLETE)
(COMPLETE)
(COMPLETE) (Note 4)
(EEP ROM)
CD-634 board
LB-124 board
PD-284 board
SI-054 board
VC-419 board
VC-419 board IC5302
Supporting
Initialization of A, B, D, 1A, 1B page data
z
Initialization of 8, C, 18, 1C page data
z
z
Initialization of E, F, 14, 19, 1E, 1F page data
z
z
Camera
67.5MHz/54MHz origin oscillation check
z
z
z
HALL adj.
z
z
z
MR adj.
z
z
z
CCD output 2ch matching adj.
z
z
z
z
Flange back and zoom lever center adj.
z
z
z
z
Mixed color compensation adj.
z
z
z
z
F No.& ND light quality standard data input
z
z
z
z
Auto white balance standard data input
z
z
z
z
LV standard data input
z
z
z
z
Auto white balance adj.
z
z
z
z
Color reproduction adj.
z
z
z
z
MAX GAIN adj.
z
z
z
z
Mechanical shutter adj.
z
z
z
Strobe light level adj.
z
z
z
z
Strobe white balance adj.
z
z
z
z
Steadyshot check
z
z
z
z
EVF
EVF automatic adj.
z
z
z
White balance adj.
z
z
z
LCD
LCD automatic adj.
z
z
z
z
V-COM adj.
z
z
z
Transmissive mode white balance adj.
z
z
z
Touch panel adj.
z
Mechanism
Tape path adj.
System control
Node uniqe ID No. input
z
z
Servo, RF
CAP FG duty adj.
z
z
z
Switching position adj.
z
z
z
Error rate check
z
z
z
Video
IC4701 LINE OUT Y level adj.
z
z
IC4701 LINE OUT chroma level adj.
z
z
S VIDEO OUT Y level adj.
z
z
S VIDEO OUT chroma level adj.
z
z
IC4701 automatic sdj.
z
z
Initialization of 8,
A, B, C, D, E, F, 14,
18, 19, 1A, 1B, 1C,
1E, 1F page data
A, B, C, D, E, F, 14,
18, 19, 1A, 1B, 1C,
1E, 1F page data
Replaced part
RadarW
RadarW
RadarW
Note 2: When the repair is finished,
confirm the following items.
1. Shoot the all black subject, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
2. Shoot a subject of low light, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
3. Shoot a subject of normal light, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
When the above symptom occurs,
perform the whole process of
“CCD Output 2ch Matching Ad-
justment”.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
When the above symptom occurs,
perform the whole process of
“CCD Output 2ch Matching Ad-
justment”.
Note 3: IC5202 (Flash memory) on
the VC-419 board cannot be
replaced.
replaced.
Note 4: When replacing the VC-419
board, perform “Exif Model
Data check” after replace-
ment.
Data check” after replace-
ment.
6-5
DCR-HC94E/HC96/HC96E_ADJ
J-13
J-14
J-15
J-10
J-9
J-7
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-4
Color bar chart
For PTB-450:
J-6020-250-A
J-6020-250-A
For PTB-1450:
J-6082-559-A
J-6082-559-A
J-5
Clear chart
For PTB-450:
J-6080-621-A
J-6080-621-A
For PTB-1450:
J-6082-560-A
J-6082-560-A
J-6
J-11
J-8
J-12
J-1
Adjustment remote
commander
(RM-95)
J-6082-053-B
commander
(RM-95)
J-6082-053-B
J-16
J-18
J-3
LANC cable
J-6082-442-A
J-6082-442-A
J-2
Adjustment remote
commander
(NEW LANC JIG)
J-6082-565-A
commander
(NEW LANC JIG)
J-6082-565-A
J-17
J-19
A: CPC-15
J-6082-564-A
J-6082-564-A
B: I/F unit for
LANC control
J-6082-521-A
LANC control
J-6082-521-A
A
B
Minipattern box
J-6082-353-B
J-6082-353-B
Flange back
adjustment jig
J-6082-563-A
adjustment jig
J-6082-563-A
Siemens star chart
J-6080-875-A
J-6080-875-A
Filter for color
temperature correction
(C14)
J-6080-058-A
temperature correction
(C14)
J-6080-058-A
ND filter 1.0
J-6080-808-A
J-6080-808-A
ND filter 0.4
J-6080-806-A
J-6080-806-A
ND filter 0.1
J-6080-807-A
J-6080-807-A
Camera table
J-6082-384-A
J-6082-384-A
Tracking standard
(XH2-1)
8-967-997-01
(XH2-1)
8-967-997-01
SW/OL standard
(XH2-3)
8-967-997-11
(XH2-3)
8-967-997-11
Audio operation check
for NTSC (XH5-3)
8-967-997-51
8-967-997-51
for PAL (XH5-3P)
8-967-997-55
8-967-997-55
System operation check
for NTSC (XH5-5)
8-967-997-61
8-967-997-61
for PAL (XH5-5P)
8-967-997-66
8-967-997-66
AC power adaptor
(AC-L25A/L25B)
1-479-288-13
(AC-L25A/L25B)
1-479-288-13
Mixed color
compensation chart
compensation chart
For PTB-450:
J-6082-558-A
J-6082-558-A
For PTB-1450:
J-6082-561-A
J-6082-561-A
1-2. List of service tools
• Oscilloscope
• Oscilloscope
• Color monitor
• Vectorscope
• Digital voltmeter
• Frequency counter
• Audio level meter
• Audio generator
• Audio attenuator
• Audio distortion meter
Fig. 6-1-1
6-6
DCR-HC94E/HC96/HC96E_ADJ
Fig. 6-1-2
Fig. 6-1-3
6-1. CAMERA SECTION ADJUSTMENTS
1-1.
PREPARATIONS BEFORE ADJUSTMENTS
(CAMERA SECTION)
(CAMERA SECTION)
1-1-1.
Preparations
Note: Before perform the adjustment, check that the data of page:
0, address: 10 is “00”.
If not, select page: 0, address: 10, and set data “00”.
If not, select page: 0, address: 10, and set data “00”.
1) Connect the equipment for adjustments according to Fig. 6-1-
3.
Pattern box
Front of the lens
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
L = 40 cm (PTB-1450)
L
Camera
A/V OUT
Adjustment remote
commander
commander
(RM-95)
(NEW LANC JIG)
A/V jack (Except DCR-HC94E)
A/V OUT jack (DCR-HC94E)
A/V OUT jack (DCR-HC94E)
AC adaptor
AC IN
To DC IN jack
Audio L
(White)
(White)
Audio R
(Red)
(Red)
Video
(yellow)
(yellow)
S Video
(Black)
(Black)
Color monitor Vectorscope
Terminated
75
Ω
6-7
DCR-HC94E/HC96/HC96E_ADJ
H
A=B
C=D
A B
B
C
D
A
Enlargement
V
Electronic beam scanning frame
CRT picture frame
B
A
Difference in level
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Y
ello
w
Cy
an
Green
White
Magenta
Red
Blue
Color bar chart (Color reproduction adjustment frame)
Fig. a
(VIDEO terminal of A/V jack
output waveform)
(VIDEO terminal of A/V jack
output waveform)
Fig. b (monitor TV picture)
Adjust the camera zoom and direction to
obtain the output waveform shown in Fig. a and
the monitor TV display shown in Fig. b.
obtain the output waveform shown in Fig. a and
the monitor TV display shown in Fig. b.
1-1-2.
Precaution
1.
Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1.
POWER switch (SS17000 block) .............. CAMERA-TAPE
2.
NIGHTSHOT switch (Lens block) ................................ OFF
3.
WIDE SELECT (Panel block) .......................................... 4:3
4.
BACK LIGHT (CF17000 block) ................................... OFF
5.
PROGRAM AE (MENU setting) ................................ AUTO
6.
EXPOSURE (MENU setting) ..................................... AUTO
7.
WHITE BAL. (MENU setting) ................................... AUTO
8.
AE SHIFT ............................................................................. 0
9.
FOCUS (MENU setting) ...................................... MANUAL
10. TELE MACRO ............................................................... OFF
11. COLOR SLOW S (MENU setting) ................................ OFF
12. ZEBRA ........................................................................... OFF
13. DIGITAL ZOOM (MENU setting) ................................ OFF
14. STEADY SHOT (MENU setting) .................................. OFF
15. D. EFFECT (MENU setting) ......................................... OFF
16. PICT. EFFECT (MENU setting) .................................... OFF
17. DEMO MODE (MENU setting) .................................... OFF
11. COLOR SLOW S (MENU setting) ................................ OFF
12. ZEBRA ........................................................................... OFF
13. DIGITAL ZOOM (MENU setting) ................................ OFF
14. STEADY SHOT (MENU setting) .................................. OFF
15. D. EFFECT (MENU setting) ......................................... OFF
16. PICT. EFFECT (MENU setting) .................................... OFF
17. DEMO MODE (MENU setting) .................................... OFF
2.
Order of Adjustments
Basically carry out adjustments in the order given.
3.
Subjects
1) Color bar chart (Color reproduction adjustment frame)
When performing adjustments using the color bar chart, ad-
just the picture frame as shown in Fig. 6-1-4. (Color reproduc-
tion adjustment frame)
just the picture frame as shown in Fig. 6-1-4. (Color reproduc-
tion adjustment frame)
2) Mixed color compensation chart (Color reproduction adjust-
ment frame)
Remove the color bar chart from the pattern box and insert a
mixed color compensation chart in its place. (Do not perform
zoom operations during this time)
Remove the color bar chart from the pattern box and insert a
mixed color compensation chart in its place. (Do not perform
zoom operations during this time)
3) Clear chart (AWB adjustment frame)
Shoot the color bar chart. Then adjust the zoom to TELE side
from WIDE side, and stop it when the black frame of the chart
disappears. Remove the color bar chart from pattern box and
insert a clear chart in its place.
from WIDE side, and stop it when the black frame of the chart
disappears. Remove the color bar chart from pattern box and
insert a clear chart in its place.
4) Chart for flange back adjustment
Join together a piece of white A0 size paper (1189mm
× 841
mm) and a piece of black paper to make the chart shown in
Fig. 6-1-5.
Fig. 6-1-5.
Note: Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white
and black paper must not have any undulations.
and black paper must not have any undulations.
Fig. 6-1-5
Black
White
841 mm
1189 mm
Fig. 6-1-4
Click on the first or last page to see other DCR-HC94E / DCR-HC96 / DCR-HC96E (serv.man4) service manuals if exist.