Sony DCR-HC94E / DCR-HC96 / DCR-HC96E (serv.man4) Service Manual ▷ View online
6-2
DCR-HC94E/HC96/HC96E_ADJ
Precaution on Replacing the VC-419 Board
• Perform “Exif Model Data Check” mentioned below, and also the adjustment items necessary after VC Board re-
placement.
Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
Exif Model Data
Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: C, address: D2 to D4, and set the Exif Model Data.
Note: To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
1) Select page: 0, address: 01 and set data: 01.
2) Select page: C, address: D2 to D4, and set the Exif Model Data.
Note: To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Page
C
C
C
DCR-HC94E
39
34
45
Address
D2
D3
D4
Data
DCR-HC96
39
36
00
DCR-HC96E
39
36
45
6-3
DCR-HC94E/HC96/HC96E_ADJ
Table 6-1-1 (1)
1-1. Adjusting items when replacing main parts and boards
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note 1: When replacing the drum assy or the mechanism deck, reset the data of page: 7, address: A8 to AB to “00”. (Refer to “Record of
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note 1: When replacing the drum assy or the mechanism deck, reset the data of page: 7, address: A8 to AB to “00”. (Refer to “Record of
Use check” of “6-4. SERVICE MODE”)
Replaced part
Adjustment Section
Adjustment
(LCD panel, Touch panel)
(LCD panel)
(Drum assembly) (Note 1)
(CCD imager)
(Timing generator)
(S/H)
(Back light (EVF))
(Back lihgt (LCD))
(LCD drive)
(PANEL I/F)
(PITCH, YAW sensor)
(A/D converter)
(Video/Audio DSP)
(DV signal process)
(REC/PB AMP)
(Video audio IN/OUT)
(Aspect ratio converter)
(EVF drive)
Lens device
LCD block LCD901
EVF block LCD902
Flash unit
Mechanism deck (Note 1)
Mechanism deck M901
Mechanism deck MD block
CD-634 board IC3601
CD-634 board IC3602, X3601
CD-634 board IC3603
LB-124 board D302
PD-284 board D9602, 9603, 9605
PD-284 board IC9601
PD-284 board Q9601, 9602
SI-054 board SE401, 402
VC-419 board IC3501
VC-419 board IC4001
VC-419 board IC4201
VC-419 board IC4301
VC-419 board IC4401
VC-419 board IC4701
VC-419 board IC7001
Initialization of A, B, D, 1A, 1B page data
Initialization of 8, C, 18, 1C page data
Initialization of E, F, 14, 19, 1E, 1F page data
Camera
67.5MHz/54MHz origin oscillation check
z
HALL adj.
z
MR adj.
z
CCD output 2ch matching adj.
z
z
z
Flange back and zoom lever center adj.
z
z
Mixed color compensation adj.
z
z
z
F No.& ND light quality standard data input
z
z
Auto white balance standard data input
z
z
z
LV standard data input
z
z
z
Auto white balance adj.
z
z
z
Color reproduction adj.
z
z
z
MAX GAIN adj.
z
z
z
Mechanical shutter adj.
z
Strobe light level adj.
z
Strobe white balance adj.
z
Steadyshot check
z
EVF
EVF automatic adj.
z
z
White balance adj.
z
z
z
LCD
LCD automatic adj.
z
z
z
V-COM adj.
z
z
Transmissive mode white balance adj.
z
z
z
Touch panel adj.
z
z
Mechanism
Tape path adj.
z
z
z
System control
Node uniqe ID No. input
Servo, RF
CAP FG duty adj.
z
z
Switching position adj.
z
z
z
Error rate check
z
z
z
z
z
Video
IC4701 LINE OUT Y level adj.
z
z
IC4701 LINE OUT chroma level adj.
z
z
S VIDEO OUT Y level adj.
z
z
S VIDEO OUT chroma level adj.
z
z
IC4701 automatic adj.
z
z
z
Mounted part replacement
Initialization of 8,
A, B, C, D, E, F, 14,
18, 19, 1A, 1B, 1C,
1E, 1F page data
A, B, C, D, E, F, 14,
18, 19, 1A, 1B, 1C,
1E, 1F page data
Block replacement
6-4
DCR-HC94E/HC96/HC96E_ADJ
• Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
Table 6-1-1 (2)
Adjustment Section
Adjustment
(COMPLETE)
(COMPLETE)
(COMPLETE)
(COMPLETE)
(COMPLETE) (Note 4)
(EEP ROM)
CD-634 board
LB-124 board
PD-284 board
SI-054 board
VC-419 board
VC-419 board IC5302
Supporting
Initialization of A, B, D, 1A, 1B page data
z
Initialization of 8, C, 18, 1C page data
z
z
Initialization of E, F, 14, 19, 1E, 1F page data
z
z
Camera
67.5MHz/54MHz origin oscillation check
z
z
z
HALL adj.
z
z
z
MR adj.
z
z
z
CCD output 2ch matching adj.
z
z
z
z
Flange back and zoom lever center adj.
z
z
z
z
Mixed color compensation adj.
z
z
z
z
F No.& ND light quality standard data input
z
z
z
z
Auto white balance standard data input
z
z
z
z
LV standard data input
z
z
z
z
Auto white balance adj.
z
z
z
z
Color reproduction adj.
z
z
z
z
MAX GAIN adj.
z
z
z
z
Mechanical shutter adj.
z
z
z
Strobe light level adj.
z
z
z
z
Strobe white balance adj.
z
z
z
z
Steadyshot check
z
z
z
z
EVF
EVF automatic adj.
z
z
z
White balance adj.
z
z
z
LCD
LCD automatic adj.
z
z
z
z
V-COM adj.
z
z
z
Transmissive mode white balance adj.
z
z
z
Touch panel adj.
z
Mechanism
Tape path adj.
System control
Node uniqe ID No. input
z
z
Servo, RF
CAP FG duty adj.
z
z
z
Switching position adj.
z
z
z
Error rate check
z
z
z
Video
IC4701 LINE OUT Y level adj.
z
z
IC4701 LINE OUT chroma level adj.
z
z
S VIDEO OUT Y level adj.
z
z
S VIDEO OUT chroma level adj.
z
z
IC4701 automatic sdj.
z
z
Initialization of 8,
A, B, C, D, E, F, 14,
18, 19, 1A, 1B, 1C,
1E, 1F page data
A, B, C, D, E, F, 14,
18, 19, 1A, 1B, 1C,
1E, 1F page data
Replaced part
RadarW
RadarW
RadarW
Note 2: When the repair is finished,
confirm the following items.
1. Shoot the all black subject, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
2. Shoot a subject of low light, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
3. Shoot a subject of normal light, and
confirm that a vertical line is not
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
When the above symptom occurs,
perform the whole process of
“CCD Output 2ch Matching Ad-
justment”.
displayed in the center of the
screen, and that there is no differ-
ence in left-right brightness level
of the screen.
When the above symptom occurs,
perform the whole process of
“CCD Output 2ch Matching Ad-
justment”.
Note 3: IC5202 (Flash memory) on
the VC-419 board cannot be
replaced.
replaced.
Note 4: When replacing the VC-419
board, perform “Exif Model
Data check” after replace-
ment.
Data check” after replace-
ment.
6-5
DCR-HC94E/HC96/HC96E_ADJ
J-13
J-14
J-15
J-10
J-9
J-7
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
J-4
Color bar chart
For PTB-450:
J-6020-250-A
J-6020-250-A
For PTB-1450:
J-6082-559-A
J-6082-559-A
J-5
Clear chart
For PTB-450:
J-6080-621-A
J-6080-621-A
For PTB-1450:
J-6082-560-A
J-6082-560-A
J-6
J-11
J-8
J-12
J-1
Adjustment remote
commander
(RM-95)
J-6082-053-B
commander
(RM-95)
J-6082-053-B
J-16
J-18
J-3
LANC cable
J-6082-442-A
J-6082-442-A
J-2
Adjustment remote
commander
(NEW LANC JIG)
J-6082-565-A
commander
(NEW LANC JIG)
J-6082-565-A
J-17
J-19
A: CPC-15
J-6082-564-A
J-6082-564-A
B: I/F unit for
LANC control
J-6082-521-A
LANC control
J-6082-521-A
A
B
Minipattern box
J-6082-353-B
J-6082-353-B
Flange back
adjustment jig
J-6082-563-A
adjustment jig
J-6082-563-A
Siemens star chart
J-6080-875-A
J-6080-875-A
Filter for color
temperature correction
(C14)
J-6080-058-A
temperature correction
(C14)
J-6080-058-A
ND filter 1.0
J-6080-808-A
J-6080-808-A
ND filter 0.4
J-6080-806-A
J-6080-806-A
ND filter 0.1
J-6080-807-A
J-6080-807-A
Camera table
J-6082-384-A
J-6082-384-A
Tracking standard
(XH2-1)
8-967-997-01
(XH2-1)
8-967-997-01
SW/OL standard
(XH2-3)
8-967-997-11
(XH2-3)
8-967-997-11
Audio operation check
for NTSC (XH5-3)
8-967-997-51
8-967-997-51
for PAL (XH5-3P)
8-967-997-55
8-967-997-55
System operation check
for NTSC (XH5-5)
8-967-997-61
8-967-997-61
for PAL (XH5-5P)
8-967-997-66
8-967-997-66
AC power adaptor
(AC-L25A/L25B)
1-479-288-13
(AC-L25A/L25B)
1-479-288-13
Mixed color
compensation chart
compensation chart
For PTB-450:
J-6082-558-A
J-6082-558-A
For PTB-1450:
J-6082-561-A
J-6082-561-A
1-2. List of service tools
• Oscilloscope
• Oscilloscope
• Color monitor
• Vectorscope
• Digital voltmeter
• Frequency counter
• Audio level meter
• Audio generator
• Audio attenuator
• Audio distortion meter
Fig. 6-1-1
