DOWNLOAD Sony DCR-HC65 Service Manual ↓ Size: 2.98 MB | Pages: 45 in PDF or view online for FREE

1. SERVICE NOTE
2. DISASSEMBLY

3. BLOCK DIAGRAMS

4. PRINTED WIRING BOARDS AND

SCHEMATIC DIAGRAMS

5. REPAIR PARTS LIST

6. ADJUSTMENTS

OVERALL
POWER
CD-513, CK-141, FS-087, JK-268,
JM-016, LB-102, MI-051, MS-210,
PD-219, SL-064 BOARD,  CONTROL
KEY BLOCK (SB7800, PS7800,
FK7800), FP-228, FP467, FP-826,
FP-910, FP-911, FP-912 FLEXIBLE

EXPLODED VIEWS
ELECTRICAL PARTS LIST

• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987672841.pdf).

• Reference No. search on printed wiring boards is available.

DCR-HC65

US Model

Canadian Model

E Model

Korean Model

Z (Z200) MECHANISM

— 2 —

1.

Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.

2.

Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.

3.

Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.

4.

Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.

5.

Check the B+ voltage to see it is at the values specified.

6.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270˚C

during repairing.

• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

• Be careful not to apply force on the conductor when soldering

or unsoldering.

Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than

ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!

• Strong viscosity

Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.

• Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer.

0

0

0

CAUTION :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

— 3 —

4-2.

SCHEMATIC DIAGRAMS

• VC-359 (1/21) (TIMING GENERATOR, S/H,

AGC, A/D CONV.)
SCHEMATIC DIAGRAM ·········································· 4-27

• VC-359 (2/21) (LENS DRIVE)

SCHEMATIC DIAGRAM ·········································· 4-29

• VC-359 (3/21) (CAMERA PROCESS)

SCHEMATIC DIAGRAM ·········································· 4-31

• VC-359 (4/21) (MPEG MOVIE/DIGITAL STILL

PROCESS)
SCHEMATIC DIAGRAM ·········································· 4-33

• VC-359 (5/21) (64Mbit SDRAM, BUFFER)

SCHEMATIC DIAGRAM ·········································· 4-35

• VC-359 (6/21) (HI/DIGITAL STILL CONTROL)

SCHEMATIC DIAGRAM ·········································· 4-37

• VC-359 (7/21) (32Mbit FLASH, 16Mbit SDRAM)

SCHEMATIC DIAGRAM ·········································· 4-39

• VC-359 (8/21) (DV SIGNAL PROCESS)

SCHEMATIC DIAGRAM ·········································· 4-41

• VC-359 (9/21) (DV INTERFACE)

SCHEMATIC DIAGRAM ·········································· 4-43

• VC-359 (10/21) (REC/PB AMP)

SCHEMATIC DIAGRAM ·········································· 4-45

• VC-359 (11/21) (VIDEO I/O)

SCHEMATIC DIAGRAM ·········································· 4-47

• VC-359 (12/21) (DRUM/CAPSTAN/LOADING

DRIVE)
SCHEMATIC DIAGRAM ·········································· 4-49

• VC-359 (13/21) (CAMERA/MECHA CONTROL)

SCHEMATIC DIAGRAM ·········································· 4-51

• VC-359 (14/21) (HI CONTROL)

SCHEMATIC DIAGRAM ·········································· 4-53

• VC-359 (15/21) (EVF VIDEO)

SCHEMATIC DIAGRAM ·········································· 4-55

• VC-359 (16/21) (AUDIO I/O)

SCHEMATIC DIAGRAM ·········································· 4-57

• VC-359 (17/21) (MIC AMP)

SCHEMATIC DIAGRAM ·········································· 4-59

• VC-359 (18/21) (DC IN, CHARGE)

SCHEMATIC DIAGRAM ·········································· 4-61

• VC-359 (19/21) (DC/DC CONVERTER)

SCHEMATIC DIAGRAM ·········································· 4-63

• VC-359 (20/21) (CONNECTOR)

SCHEMATIC DIAGRAM ·········································· 4-65

• VC-359 (21/21) (CONNECTOR)

SCHEMATIC DIAGRAM ·········································· 4-67

4-3.

PRINTED WIRING BOARDS

• VC-359 (TIMING GENERATOR, S/H, AGC, A/D

CONV., LENS DRIVE, CAMERA PROCESS, MPEG
MOVIE/DIGITAL STILL PROCESS, 64Mbit SDRAM,
BUFFER, HI/DIGITAL STILL CONTROL, 32Mbit
FLASH, 16Mbit SDRAM, DV SIGNAL PROCESS, DV
INTERFACE, REC/PB AMP, VIDEO I/O, DRUM/
CAPSTAN/LOADING DRIVE, CAMERA/MECHA
CONTROL, HI CONTROL, EVF VIDEO, AUDIO I/O,
MIC AMP, DC IN, CHARGE, DC/DC CONVERTER,
CONNECTORW
PRINTED WIRING BOARD ····································· 4-93

4-4.

MOUNTED PARTS LOCATION ································· 4-99

5-2.

ELECTRICAL PARTS LIST ········································ 5-19