Sony DCR-HC62 / DCR-HC62E (serv.man4) Service Manual ▷ View online
SECTION 6
ADJUSTMENTS
Revision History
Revision History
Sony EMCS Co.
Link
Link
Adjusting items when replacing main parts and boards
List of service tools
Before starting adjustments
ELECTRONIC VIEWFINDER SYSTEM
ADJUSTMENTS
ADJUSTMENTS
LCD SYSTEM ADJUSTMENTS
CAMERA SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
INITIALIZATION OF EVR DATA
CAMERA SECTION ADJUSTMENTS
TAPE PATH ADJUSTMENT
HOW TO ENTER PLAYBACK MODE WITHOUT
CASSETTE
CASSETTE
HOW TO ENTER RECORD MODE WITHOUT
CASSETTE
CASSETTE
MECHANISM SECTION ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
SERVO AND RF SYSTEM ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
VIDEO SECTION ADJUSTMENTS
SERVICE MODE
DATA PROCESS
ADJUSTMENT REMOTE COMMANDER (RM-95)
SERVICE MODE
ADJUSTMENT REMOTE COMMANDER
(NEW LANC JIG)
(NEW LANC JIG)
ADJ
Ver. 1.0 2007.12
9-852-235-51
2007L0800-1
© 2007.12
Published by Kohda TEC
DCR-HC62/HC62E
RMT-831
DCR-HC62/HC62E_ADJ
• Precaution on Replacing the VC-525 Board
6-1
DCR-HC62/HC62E_ADJ
SECTION 6
ADJUSTMENTS
1.
Before starting adjustments
EVR Data Re-writing Procedure When Replacing Board
The data that is stored in the repair board, is not necessarily correct.
Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a
board is replaced.
board is replaced.
Remove the EEPROM and install it.
(Former board)
(New board)
Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed
EEPROM to the replaced board.
EEPROM to the replaced board.
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or
installed, save the data from the same model of the same destination, and download it.
installed, save the data from the same model of the same destination, and download it.
After the EVR data is saved and downloaded, check the
respective items of the EVR data.
(Refer to page 6-3 for the items to be checked)
respective items of the EVR data.
(Refer to page 6-3 for the items to be checked)
(Machine before starting repair)
(Machine after a board is replaced)
PC
PC
Save the EVR data
to a personal computer.
to a personal computer.
Download the saved
data to a machine.
data to a machine.
(Machine to be repaired)
(Machine to be repaired)
(The same model of the same destination)
Save the data.
Download the data.
PC
6-2
DCR-HC62/HC62E_ADJ
Precaution on Replacing the VC-525 Board
• Perform “Exif Model Data Check” mentioned below, and also the adjustment items necessary after VC Board re-
placement.
Exif Model Data Check
When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not,
rewrite to the right value.
Exif Model Data
Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: C, address: D2 to D4, and set the Exif Model Data.
Note: To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
1) Select page: 0, address: 01 and set data: 01.
2) Select page: C, address: D2 to D4, and set the Exif Model Data.
Note: To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Address
D2
D3
D4
Page
C
C
C
Data
DCR-HC62
36
32
00
DCR-HC62E
36
32
45
6-3
DCR-HC62/HC62E_ADJ
Table 6-1-1 (1)
1-1.
Adjusting items when replacing main parts and boards
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Note 1: When replacing the drum assy or the mechanism deck, reset the data of page: 7, address: A8 to AB to “00”. (Refer to “Record of
When replacing main parts, adjust the items indicated by z in the following table.
Note 1: When replacing the drum assy or the mechanism deck, reset the data of page: 7, address: A8 to AB to “00”. (Refer to “Record of
Use check” of “6-4. SERVICE MODE”)
Adjustment
Section
Section
Adjustment
(LCD panel, Touch panel)
(EVF Unit)
(Drum assembly) (Note 1)
(CCD imager)
(PITCH, YAW sensor)
(Back light (EVF))
(Back light (LCD))
(Touch panel I/F)
(A/D converter, Timing generator)
(Camera signal process)
(Video/Audio DSP Lens Control)
(DV signal process)
(REC/PB AMP)
(Video, Audio I/O)
(Aspect ratio converter)
(DS/HI control)
(LCD/EVF drive)
Lens device
LCD block LCD901
EVF block LCD902
Mechanism deck (Note 1)
Mechanism deck M901
Mechanism deck MD block
CD-672 board IC7002
CD-672 board SE7002, 7001
LB-138 board D301
PD-359 board D6303 - 6305
PD-359 board Q6301, 6302
VC-525 board IC3201, X3201
VC-525 board IC3901
VC-525 board IC4001
VC-525 board IC4201
VC-525 board IC4301
VC-525 board IC4401
VC-525 board IC4701
VC-525 board IC5101
VC-525 board IC7001
Initialization of A, B, D, 1A, 1B page data
Initialization of 8, C, 18, 1C page data
Initialization of 63 to 6F page data
Initialization of 8, C, 18, 1C page data
Initialization of 63 to 6F page data
Camera
33MHz/27MHz origin oscillation check.
z
z
HALL adj.
z
Flange back adj.
z
z
F No. & ND light quality standard data input
z
MAX GAIN adj.
z
z
z
Mechanical shutter adj.
z
Color reproduction adj.
z
z
z
Auto white balance standard data input
z
z
z
LV standard data input
z
z
z
Auto white balance adj.
z
z
z
Steadyshot check
z
EVF
EVF automatic adj.
z z
z
White balance adj.
z
z
z
LCD
LCD automatic adj.
z z
z
V-COM adj.
z
z
Transmissive mode white balance adj.
z
z
z
Touch panel adj.
z
z
Mechanism
Tape path adj.
z z z
System control Node uniqe ID No. input
USB Serial number data setting
Replaced part
Mounted part replacement
Initialization of
EVR data
EVR data
Block replacement
