DOWNLOAD Sony DCR-HC39E / DCR-HC41 / DCR-HC42 / DCR-HC42E / DCR-HC43 / DCR-HC43E (serv.man3) Service Manual ↓ Size: 267.37 KB | Pages: 8 in PDF or view online for FREE

Model
DCR-HC39E DCR-HC41 DCR-HC42 DCR-HC42E DCR-HC43 DCR-HC43E (serv.man3)
Pages
8
Size
267.37 KB
Type
PDF
Document
Service Manual
Brand
Device
Movie / LEVEL 1
File
dcr-hc39e-dcr-hc41-dcr-hc42-dcr-hc42e-dcr-hc43-dcr.pdf
Date

Sony DCR-HC39E / DCR-HC41 / DCR-HC42 / DCR-HC42E / DCR-HC43 / DCR-HC43E (serv.man3) Service Manual ▷ View online

— 3 —
DCR-HC39E/HC42/HC42E/HC43/HC43E
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE WITH
MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 
0
 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
1.
Check the area of your repair for unsoldered or poorly-soldered
connections.  Check the entire board surface for solder splashes
and bridges.
2.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair.  Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration.  Point them out to the customer and
recommend their replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
Keep the temperature of the soldering iron around 270
°
C
during repairing.
Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
Table for differences of function
• Abbreviation
AUS : Australian model
BR
: Brazilian model
CH
: Chinese model
CND : Canadian model
EE
: East European model
HK : Hong Kong model
JE
: Tourist model
KR
: Korea model
NE
: North European model
Model
DCR-HC39E
DCR-HC42
DCR-HC42E
DCR-HC43
DCR-HC43E
Destination
AEP, UK, NE, EE
US, CND, E, KR,
AEP, UK, NE, EE,
BR
CH, E
JE
E, AUS, HK, JE
Color system
PAL
NTSC
PAL
NTSC
PAL
Electrical viewfinder
Black and White
Color
Color
Color
Color
A/V jack
OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
DV Interface on the Cradle
OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
(Handycam Station)
— 4 —
DCR-HC39E/HC42/HC42E/HC43/HC43E
1.
Self-diagnosis Function
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or LCD
screen what to do. This function consists of two display; self-
diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
2. Self-diagnosis Display
When problems occur while the unit is operating, the counter of the
viewfinder or LCD screen shows a 4-digit display consisting of an
alphabet and numbers, which blinks at 3.2 Hz. This 5-character
display indicates the “repaired by:”, “block” in which the problem
occurred, and “detailed code” of the problem.
1 1
3 1
C
Repaired by:
Refer to “3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
Viewfinder or LCD screen
C : 3 1 : 1 1
SELF-DIAGNOSIS FUNCTION
— 5 —
DCR-HC39E/HC42/HC42E/HC43/HC43E
3.
Self-diagnosis Code Table
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Block
Function
0
4
2
1
2
2
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
Detailed
Code
0
0
0
0
0
0
1
0
1
1
2
0
2
1
2
2
2
3
3
0
3
1
4
0
4
1
4
2
4
3
4
4
1
0
1
1
2
0
2
1
2
2
2
3
3
0
3
1
4
0
4
1
4
2
4
3
4
4
Symptom/State
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading.
S reel side tape slacking when unloading.
T reel fault.
S reel fault.
FG fault when starting capstan.
FG fault during normal capstan operations.
FG fault when starting drum.
PG fault when starting drum.
FG fault during normal drum operations.
PG fault during normal drum operations.
Phase fault during normal drum operations.
LOAD direction loading motor time-
out.
UNLOAD direction loading motor
time-out.
T reel side tape slacking when
unloading.
S reel side tape slacking when
unloading.
T reel fault.
S reel fault.
FG fault when starting capstan.
FG fault during normal capstan
operations.
FG fault when starting drum.
PG fault when starting drum.
FG fault during normal drum
operations.
PG fault during normal drum
operations.
Phase fault during normal drum
operations.
Self-diagnosis Code
Repaired b
y:
Correction
Use the InfoLITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
— 6 —
DCR-HC39E/HC42/HC42E/HC43/HC43E
1.  ORNAMENTAL  PARTS
Note:
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The parts numbers of such as a cabinet are also appeared in this section.
Refer to the parts number mentioned below the name of parts to order.
• Abbreviation
AUS : Australian model
CH
: Chinese model
CND : Canadian model
EE
: East European model
HK : Hong Kong model
JE
: Tourist model
KR
: Korean model
NE
: North European model
1.  MAIN  PARTS
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Shoe cover (106)
2-188-484-01
Cpc lid
2-188-478-01
Screw (M1.7) 
3-080-198-11
Jack cover
2-188-477-01
(When change it, need dismantle the set.)
Page of 8
Display

Sony DCR-HC39E / DCR-HC41 / DCR-HC42 / DCR-HC42E / DCR-HC43 / DCR-HC43E (serv.man3) Service Manual ▷ Download

  • DOWNLOAD Sony DCR-HC39E / DCR-HC41 / DCR-HC42 / DCR-HC42E / DCR-HC43 / DCR-HC43E (serv.man3) Service Manual ↓ Size: 267.37 KB | Pages: 8 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony DCR-HC39E / DCR-HC41 / DCR-HC42 / DCR-HC42E / DCR-HC43 / DCR-HC43E (serv.man3) in PDF for free, which will help you to disassemble, recover, fix and repair Sony DCR-HC39E / DCR-HC41 / DCR-HC42 / DCR-HC42E / DCR-HC43 / DCR-HC43E (serv.man3) Movie. Information contained in Sony DCR-HC39E / DCR-HC41 / DCR-HC42 / DCR-HC42E / DCR-HC43 / DCR-HC43E (serv.man3) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.