Sony DCR-HC30 (serv.man2) Service Manual ▷ View online
1-1
SEÇÃO 1
NOTA DE SERVIÇO
DCR-HC30
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
1-1. NOTA DE SERVIÇO
1.
NOTE FOR REPAIR
ENGLISH
ENGLISH
1-2
DCR-HC30
2.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.
Use the AC power adaptor.
Method 2.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
3.
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1
Remove the cabinet (R) section.
2
Remove the front panel block assembly.
3
Remove the BAT, EVF block assembly.
4
Remove the lens block assembly.
5
Remove the mechanism deck and the VC-351 board.
6
Open the VC-351 board.
7
Disconnect CN9102 (27P, 0.3mm) of VC-351 board.
8
Supply +4.5V from the DC power supply to the loading motor and unload with pressing the cassette compartment.
ENGLISH
ENGLISH
VC-351
CN9102
VC-351 board
DC power supply (+4.5Vdc)
Loading motor
Disconnect the flexible board from
CN9102 of VC-351 board.
CN9102 of VC-351 board.
DCR-HC30
Link
Link
2. DESMONTAGEM
LOCALIZAÇÃO DAS PLACAS
POSIÇÃO DO SERVIÇO LOCALIZAÇÃO DAS PLACAS FLEXÍVEIS
DESMONTAGEM
AJUDA
2. DESMONTAGEM
DCR-HC30
2-1
2-2
2-1. DESMONTAGEM
The following flow chart shows the disassembly procedure.
VC
-351
VC
-351
VC
-351
VC
-351
VC
-351
VC
-351
3
2
3
2
6
qs
4
2
3
5
6
1
4
7
1
8
5
4
3
1
2
7
0
9
4
4
5
6
7
8
0
9 qa
3
8
6
7
2
4
5
3
3
5
2
3
1
2
1
1
2
3
1
9
4
6
1
Shoe cover
2
Two special screws (M2x2.8) silver
3
Cold shoe
1
Two screws (M1.7x3) silver
2
Five tapping screws (M1.7x4) black
3
Screw (M1.7x3) silver
4
Open the G cabinet (64) assembly.
5
Two claws
1
Two tapping screws (M1.7x6) black
2
Hinge blind
3
LCD section
4
Cabinet (R) section
1
Two screws (M1.7x3) silver
2
Two tapping screws (M1.7x5) black
3
P cabinet (C) assembly
4
Tape (A)
5
FP-835 flexible board (22P)
6
Hinge section
1
Screw (M1.7
×
2.5) black
2
Four claws
3
Hinge cover (M), FP-836 flexible board
4
Hinge cover (C)
5
FP-835 flexible board, Hinge section
1
Two tapes (W)
2
Screw (M1.7x2.5) black
3
From lens flexible board (23P)
4
SS6300 control key block (18P)
5
to
qa
(CN1105 (20P), CN1108 (39P), CN6501 (10P), CN9101 (10P), CN9102 (27P),
CN9103 (27P), CN4001 (14P)) of VC-351 board
qs
VC-351 board
1
Two tapes (W)
2
From lens flexible board (23P)
3
FP-833 flexible board (6P)
4
FP-827 flexible board (14P)
5
Two screws (M1.7x2.5) black
6
Lens block assembly
1
Screw (M1.7x3) silver
2
BAT section
3
EVF section
1
Two tapping screws (M1.7x5) black
2
Two screws (M1.7x3) silver
3
P cabinet (C) assembly
qa
qs
7
SB6300 control key block (6P)
8
Tapping screw (M1.7x5) black
9
Two claws
0
Panel cushion
qa
P cabinet (M) assembly
qs
PD-213 board, LCD unit (ACX528AKN-J),
Light guide plate block
7
FP-836 flexible board (6P)
8
FP-835 flexible board (22P)
9
Cabinet (R) section
5
FP-830 flexible board (26P)
6
FP-831 flexible board (20P)
7
BAT, EVF block assembly
HELP 01
1
2
5
3
4
2
1
1
3
4
7
3
1
2
5
6
1
FP-833 flexible board (39P)
2
FP-832 flexible board (20P)
3
SS6300 control key block (18P)
4
Screw (M1.7x2.5) black
5
Two screws (M1.7x2.5) black
6
Open the G cabinet (64) assembly.
7
VC-351 board, Mechanism deck, MD frame assembly
FFC-036 flexible board
2
1
Screw (M1.7x4) black
2
Screw (M1.7x2.5) black
3
Screw (M1.7x4) black
4
Two tapes (A)
7
6
2
4
3
1
1
Open the G cabinet (64) assembly.
2
Screw (M1.7x2.5) black
3
Eject knob
4
Six tapping screws (M1.7x4) silver
5
Two screws (M1.7x2.5) black
6
FP-832 flexible board
7
G cabinet (64) assembly, MS board,
FP-832 flexible board
HELP 03
5
5
1
2
3
1
Shoe cover
2
Tapping screw (M1.7x5) black
3
EYE cup assembly
1
1
Three screws (M1.7x3) silver
2
FFC-036 flexible flat cable (16P)
3
Claw
4
F panel block assembly
5
Cushion (F2)
6
CF6300 control key block (8P)
HELP 02
(disassembly of the EVF section)
(disassembly of the EVF section)
Click on the first or last page to see other DCR-HC30 (serv.man2) service manuals if exist.