Sony DCR-HC23E / DCR-HC24E / DCR-HC26 / DCR-HC26E / DCR-HC35E (serv.man4) Service Manual ▷ View online
6-15
DCR-HC23E/HC24E/HC26/HC26E/HC35E_ADJ
1-2-3.
Initialization of E, F, 1F Page Data
Note: Check that the data of page: 0, address: 10 is “00”.
1.
Initializing of E, F, 1F Page Data
Note 1: If “Initialization of Pages E, F, 1F” is executed, all data
on pages E, F, 1F are initialized. (Only an individual page
cannot be initialized)
cannot be initialized)
Note 2: If the E, F, 1F page data has been initialized, the follow-
ing adjustments need to be performed again.
1) Modification of E, F, 1F page data
2) Camera system adjustments
1) Modification of E, F, 1F page data
2) Camera system adjustments
Note 3: NTSC model: DCR-HC26
PAL model: DCR-HC23E/HC24E/HC26E/HC35E
Adjustment Page
E
Adjustment Address
00 to FF
Adjustment Page
F
Adjustment Address
10 to FF
Adjustment Page
1F
Adjustment Address
00 to FF
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
0
10
00
3
6
01
Set the following data, and
press PAUSE button.
press PAUSE button.
2D: NTSC model
2F: PAL model
2F: PAL model
4
6
03
FF
Press PAUSE (Write) button.
5
6
02
Check the data changes to
“01”.
“01”.
6
6
01
00
Press PAUSE (Write) button.
7
Perform “Modification of E,
F, 1F Page Data”
F, 1F Page Data”
2.
Modification of E, F, 1F Page Data
If the E, F, 1F page data has been initialized, change the data of
the “Fixed data-2” address shown in the following table by manual
input.
the “Fixed data-2” address shown in the following table by manual
input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) If modification of data on pages E, F, set data: 00 to page: 0,
address: 10, and then select pages E, F.
3) If modification of data on pages 1F, set data: 01 to page: 0,
address: 10, and then select pages F. After the modification of
data finished, return the data on page: 0, address: 10 to “00”.
data finished, return the data on page: 0, address: 10 to “00”.
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the
the data built in the same model.
Note: If copy the data built in the different model, the
camcorder may not operate.
5) When changing the data, press the PAUSE (Write) button of
the adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
data to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value.
If not, change the data to the initial value.
Processing after completing modification E, F, 1F page data:
Order Page Address Data
Procedure
1
0
10
00
2
2
00
29
3
2
01
29
Press PAUSE (Write) button.
4
Perform “36MHz Origin
Oscillation Adjustment” of
CAMERA SYSTEM
ADJUSTMENTS.
Oscillation Adjustment” of
CAMERA SYSTEM
ADJUSTMENTS.
6-16
DCR-HC23E/HC24E/HC26/HC26E/HC35E_ADJ
3.
E Page Table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of E, F, 1F Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to C4
Fixed data-1 (Initialized data)
C5
Fixed data-2
C6 to DA
Fixed data-1 (Initialized data)
DB
Fixed data-2
DC to FE
Fixed data-1 (Initialized data)
FF
Fixed data-2
4.
F Page Table
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of E, F, 1F Page Data”)
Address
Initial value
Remark
NTSC PAL
10
80
80
36MHz origin osillation adj.
11
Fixed data-1 (Initialized data)
12
50
50
Hall adj.
13
50
50
14
89
89
15
00
00
16
17
17
17
00
00
18
00
00
19
Fixed data-2
1A
36
36
LV standard data input
1B
00
00
1C
00
00
F No. standard data input
1D
00
00
1E
00
00
1F
00
00
20
00
00
21
00
00
22
00
00
23
00
00
24 to 29
Fixed data-1 (Initialized data)
2A
23
23
2B
92
B1
Auto white balance standard data
2C
08
07
input
2D
04
F8
2E
15
15
Auto white balance adj.
2F
9D
99
30
0D
0D
31
57
41
32
Fixed data-1 (Initialized data)
33
41
42
Color reproduction adj.
34
Fixed data-1 (Initialized data)
35
2C
2A
Color reproduction adj.
36 to 39
Fixed data-1 (Initialized data)
3A
00
00
Color reproduction adj.
3B
F0
EE
3C, 3D
Fixed data-1 (Initialized data)
3E
29
29
Auto white balance adj.
3F
40
40
40
5B
5B
41
80
80
42, 43
Fixed data-1 (Initialized data)
6-17
DCR-HC23E/HC24E/HC26/HC26E/HC35E_ADJ
F Page Table
Address
Initial value
Remark
NTSC PAL
44
3A
3A
Flange back adj.
45
74
74
46
3F
3F
47
2C
2C
48
17
17
49
4A
4A
4A
00
00
4B
00
00
4C
00
00
4D
00
00
4E
4F
4F
4F
19
19
50
00
00
51
30
30
52
00
00
53
04
04
54
00
00
55 to 8C
Fixed data-1 (Initialized data)
8D
Fixed data-2
8E
Fixed data-1 (Initialized data)
8F
Fixed data-2
90 to 96
Fixed data-1 (Initialized data)
97
Fixed data-2
98 to F5
Fixed data-1 (Initialized data)
F6
F7
Fixed data-2
F8
F9 to FE
Fixed data-1 (Initialized data)
FF
Fixed data-2
5.
1F Page Table
Note 1: If reading/writing data on pages 1F, set data: 01 to page:
0, address: 10, and then select pages F. By this data set-
ting, the pages 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
ting, the pages 1F can be selected.
After the data reading/writing finished, return the data
on page: 0, address: 10 to “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of E, F, 1F Page Data”)
Fixed data-2: Modified data. (Refer to “2. Modification
of E, F, 1F Page Data”)
Address
Initial value
Remark
NTSC PAL
00 to 59
Fixed data-1 (Initialized data)
5A
00
00
5B
00
00
Emergency memory address
5C
00
00
(Camera section)
5D
00
00
5E to 80
Fixed data-1 (Initialized data)
81
Fixed data-2
82 to FF
Fixed data-1 (Initialized data)
6-18
DCR-HC23E/HC24E/HC26/HC26E/HC35E_ADJ
2.
HALL Adjustment
RadarW
RadarW
RadarW
For detecting the position of lens iris, adjust the hall AMP gain
and offset.
and offset.
Subject
Not required
Measurement Point
Displayed data of page: 1 (Note 3)
Measuring Instrument
Adjusting remote commander
Adjustment Page
F
Adjustment Address
12 to 18
Specified value
Data of page: 6, address: 0C is “00”
Note 1: Check that the data of page: 0, address: 10 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.
Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, select page: 6, address: 01, set data: 00, and press
the PAUSE (Write) button.
the PAUSE (Write) button.
Switch setting:
1) POWER ......................................................... CAMERA mode
1) POWER ......................................................... CAMERA mode
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
6
D0
40
3
6
01
6D
Press PAUSE (Write) button.
(Note 3)
(Note 3)
4
6
02
Check the data changes to
“01”.
“01”.
5
6
0C
Check the data is “00”.
Note 3: The adjustment data will be automatically input to page:
F, address: 12 to 18.
Processing after completing adjustment:
Order Page Address Data
Procedure
1
6
01
00
Press PAUSE (Write) button.
2
0
01
00
1-3.
CAMERA SYSTEM ADJUSTMENTS
Before perform the camera system adjustments, check that the
specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat-
isfied. (Except “36MHz Origin Oscillation Adjustment”)
Check that the data of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat-
isfied. (Except “36MHz Origin Oscillation Adjustment”)
Check that the data of page: 0, address: 10 is “00”.
If not, select page: 0, address: 10, and set the data “00”.
1.
36MHz Origin Oscillation Adjustment
(VC-416 board)
(VC-416 board)
Set the frequency of the clock for synchronization.
If deviated, the synchronization will be disrupted and the color
will become inconsistent.
If deviated, the synchronization will be disrupted and the color
will become inconsistent.
Subject
Not required
Measurement Point
Pin qh of IC3002 on VC-416 board
Measuring Instrument
Frequency counter
Adjustment Page
F
Adjustment Address
10
Specified value
f = 18000000
± 90 Hz
Note 1: Check that the data of page: 0, address: 10 is “00”.
Adjusting method:
Order Page Address Data
Procedure
1
0
01
01
2
F
10
Change the data and set the
frequency (f) to the specified
value.
frequency (f) to the specified
value.
3
F
10
Press PAUSE (Write) button.
4
0
01
00
Fig. 6-1-8
48
1
12
1316
Measurement Point
37
36
24
25
IC3002
VC-416 board (SIDE A)
Click on the first or last page to see other DCR-HC23E / DCR-HC24E / DCR-HC26 / DCR-HC26E / DCR-HC35E (serv.man4) service manuals if exist.