DOWNLOAD Sony DCR-HC23E / DCR-HC24E / DCR-HC26 / DCR-HC26E / DCR-HC35E (serv.man2) Service Manual ↓ Size: 4.81 MB | Pages: 64 in PDF or view online for FREE

1-4E

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2

E

E

E

Block

Function

6

1

6

1

6

1

Detailed

Code

0

0

1

0

1

1

Symptom/State

Difficult to adjust focus
(Cannot initialize focus.)

Zoom operations fault
(Cannot initialize zoom lens.)

Focus lens initializing failure and zoom
lens initializing failure occur simulta-
neously.

Self-diagnosis Code

Repaired b

y:

Correction

Inspect the lens block focus reset sensor (Pin ql,  of CN3101 of VC-
416 board) when focusing is performed when the touch panel is
operated in the focus manual mode and the focus motor drive circuit
(IC3101 of VC-416 board) when the focusing is not performed.

Inspect the lens block zoom reset sensor (Pin qg, of CN3101 of
VC-416 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive circuit (IC3101 of VC-416
board) when zooming is not performed.

Inspect the flexible board for breakage or loose connection.
If not faulty, inspect the focus and zoom motor drive circuit (IC3101
of VC-416 board).

When you replace to the repairing board, the written data of repairing board also might be changed to original setting.
When the data has changed because of board replaceing etc, check the data setting (Exif Model Data) is right. If not, rewrite to the right value.

Writing Method:
1) Select page: 0, address: 01 and set data: 01.
2) Select page: C, address: D2 to D4, and set the Exif Model Data.

 To write in the non-volatile memory (EEPROM), press the PAUSE (Write) button each time to set the data.

3) Select page: 0, address: 01, and set data: 00.

Page

C

C

C

Data

DCR-HC23E

32

33

45

DCR-HC24E

32

34

45

DCR-HC26

32

36

00

Address

D2

D3

D4

DCR-HC26E

32

36

45

DCR-HC35E

33

35

45

2-1

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2

Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.

• When installing a connector, dont’ press down at wire of connector.

It is possible that a wire is snapped.

2-2

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2

2

-1 (Open the Cassette Lid)

2

-4 

(Claw)

2

-5 

(Shaft)

2

-2 (#2)

2

-3 (#2)

3

-2 (#2)

3

-4 (Boss)

3

-1 (Open the Jack Lid)

3

-5

2

NS Cabinet Assy

3

Front Panel Block

1

Cabinet (R) block

1

-2 (#14)

1

-4 (#14)

1

-6 (#10)

1

-13

1

-14

1

-15

1

-7 (#10)

1

-9 (#10)

1

-5 (#14)

1

-1 (Slide the EVF)

1

-8 (Open the LCD)

1

-3 (Direction of the arrow

A

)

A

1

-12 (Boss)

1

-11 (Claw)

1

-10 (Claw)

3

-3 (#2)

2-3

DCR-HC23E/HC24E/HC26/HC26E/HC35E_L2

PD-281

3

-1

3

-2

1

Hinge block

3

LCD

2

PD-281 board

1

-2 (#13)

1

-3 (#12)

1

-9 (#10)

1

-14 (#3)

1

-11 (Claw)

1

-12

1

-10 (#12)

1

-6

(Boss)

1

-7 (Boss)

1

-5 (#12)

1

-1

1

-4

1

-8

2

-2

2

-6

2

-7

2

-3

2

-1

2

-4 (#12)

2

-5 (Claw)

2

-8 (Claw)

1

-13

1

-15