Sony DCR-HC21 (serv.man2) Service Manual ▷ View online
6-70
DCR-HC21
Hexadecimal-decimal Conversion Table
Lower digit of
hexadecimal
Upper digit
of hexadecimal
of hexadecimal
0
1
2
3
4
5
6
7
8
9
A
(
A
)
B
(
b
)
C
(
c
)
D
(
d
)
E
(
E
)
F
(
F
)
0
1
2
3
4
5
6
7
8
9
A (
A
)
B (
b
)
C (
c
)
D (
d
)
E (
E
)
F (
F
)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
77
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
174
159
175
160
161
162
163
164
165
166
167
168
169
170
171
172
173
177
176
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
0
1
Note:
The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander.
(Example)
If the DDS display or the adjustment remote commander shows BD (
bd
);
Because the upper digit of the adjustment number is B (
b
), and the lower digit is D (
d
), the meeting point
“189” of 1 and 2 in the above table is the corresponding decimal number.
0
2
4-2.
DATA PROCESS
The calculation of the DDS display and the adjustment remote
commander display data (hexadecimal notation) are required for
obtaining the adjustment data of some adjustment items. In this
case, after converting the hexadecimal notation to decimal nota-
tion, calculate and convert the result to hexadecimal notation, and
use it as the adjustment data. Indicates the hexadecimal-decimal
conversion table.
commander display data (hexadecimal notation) are required for
obtaining the adjustment data of some adjustment items. In this
case, after converting the hexadecimal notation to decimal nota-
tion, calculate and convert the result to hexadecimal notation, and
use it as the adjustment data. Indicates the hexadecimal-decimal
conversion table.
Table 6-4-1
6-71
DCR-HC21
4-3.
SERVICE MODE
Note 1:
Before performing the adjustment, check the data of
page: 0, address: 10 is “00”. If not, select page: 0, ad
dress: 00, and set data “00”.
page: 0, address: 10 is “00”. If not, select page: 0, ad
dress: 00, and set data “00”.
Note 2:
Non MS model: DCR-HC17E/HC19E/HC21/HC21E/
HC22E
MS model: DCR-HC32/HC32E/HC33/HC33E
1.
Setting the Test Mode
1-1.
Setting the Test Mode (Non MS model)
Page D
Address 10
Data
Function
00
Normal
01
Forced camera power ON (CAMERA mode)
02
Forced VTR power ON (PLAY/EDIT mode)
03
Forced camera + VTR power ON
1-2.
Setting the Test Mode (MS model)
Page A
Address 10
Data
Function
00
Normal
01
Forced camera power ON (CAMERA-TAPE mode)
02
Forced VTR power ON (PLAY/EDIT mode)
03
Forced camera + VTR power ON
05
Forced memory power ON (CAMERA-MEMORY mode)
• Before setting the data , select page: 0, address: 01, and set data:
01.
• For page A, the data set will be recorded in the non-volatile
memory by pressing the PAUSE button of the adjustment re-
mote commander. In this case, take note that the test mode will
not be exited even when the main power is turned off (8.4 Vdc).
mote commander. In this case, take note that the test mode will
not be exited even when the main power is turned off (8.4 Vdc).
• After completing adjustments/repairs, be sure to return the data
of this address to 00, and press the PAUSE button of the adjust-
ment remote commander. And select page: 0, address: 01, and
set data: 00.
ment remote commander. And select page: 0, address: 01, and
set data: 00.
2.
Emergence Memory Address (Non MS model)
2-1.
Emergency Memory Address (Camera section)
Page 1F
Address 5A to 5D
Note:
If reading/writing data on pages 1F, set data: 01 to page: 0,
address: 10, and then select pages: F. By this data setting,
the pages 1F can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
address: 10, and then select pages: F. By this data setting,
the pages 1F can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
Address
Contents
5A
EMG code when first error occurs
5B
EMG code when second error occurs
5C
EMG code when third error occurs
5D
EMG code when last error occurs
When no error occurs in this unit, data “00” is written in the above
addresses (5A to 5D). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (5A). In the same way, when the second error occurs, the
data corresponding to the error is written in the second emergency
address (5B).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (5D).
addresses (5A to 5D). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (5A). In the same way, when the second error occurs, the
data corresponding to the error is written in the second emergency
address (5B).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (5D).
Note:
After completing adjustments, be sure to initialize the data
of addresses 5A to 5D to “00”.
of addresses 5A to 5D to “00”.
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
6
01
FD
Press PAUSE button.
3
6
02
Check the data changes to
“01”.
“01”.
4
6
01
00
Press PAUSE button.
5
0
01
00
2-2.
EMG Code (Emergency Code)
Codes corresponding to the errors which occur are written in 1F
page, addresses 5A to 5D. The type of error indicated by the code
are shown in the following table.
page, addresses 5A to 5D. The type of error indicated by the code
are shown in the following table.
Code
Emergency Type
00
No error
6-72
DCR-HC21
3.
Emergence Memory Address (MS model)
3-1.
Emergency Memory Address (Camera section)
Page 1F
Address 1C to 1F
Note:
If reading/writing data on pages 1F, set data: 01 to page: 0,
address: 10, and then select pages: F. By this data setting,
the pages 1F can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
address: 10, and then select pages: F. By this data setting,
the pages 1F can be selected.
After the data reading/writing finished, return the data on
page: 0, address: 10 to “00”.
Address
Contents
1C
EMG code when first error occurs
1D
EMG code when second error occurs
1E
EMG code when third error occurs
1F
EMG code when last error occurs
When no error occurs in this unit, data “00” is written in the above
addresses (1C to 1F). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (1C). In the same way, when the second error occurs, the
data corresponding to the error is written in the second emergency
address (1D).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (1F).
addresses (1C to 1F). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (1C). In the same way, when the second error occurs, the
data corresponding to the error is written in the second emergency
address (1D).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (1F).
Note:
After completing adjustments, be sure to initialize the data
of addresses 1C to 1F to “00”.
of addresses 1C to 1F to “00”.
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
6
01
FD
Press PAUSE button.
3
6
02
Check the data changes to
“01”.
“01”.
4
6
01
00
Press PAUSE button.
5
0
01
00
3-2.
EMG Code (Emergency Code)
Codes corresponding to the errors which occur are written in 1F
page, addresses 1C to 1F. The type of error indicated by the code
are shown in the following table.
page, addresses 1C to 1F. The type of error indicated by the code
are shown in the following table.
Code
Emergency Type
00
No error
4.
Emergence Memory Address (Mechanism
section)
section)
Page C
Address F4 to FF
Address
Contents
F4
EMG code when first error occurs
F6
Upper: MSW code when shift starts when first error
occurs
Lower: MSW code when first error occurs
F7
Lower: MSW code to be moved when first error
occurs
F8
EMG code when second error occurs
FA
Upper: MSW code when shift starts when second
error occurs
Lower: MSW code when second error occurs
FB
Lower: MSW code to be moved when second error
occurs
FC
EMG code when last error occurs
FE
Upper: MSW code when shift starts when last error
occurs
Lower: MSW code when last error occurs
FF
Lower: MSW code to be moved when last error
occurs
When no error occurs in this unit, data “00” is written in the above
addresses (F4 to FF). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (F4 to F7). In the same way, when the second error occurs,
the data corresponding to the error is written in the second emer-
gency address (F8 to FB).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (FC to FF).
addresses (F4 to FF). when first error occurs in the unit, the data
corresponding to the error is written in the first emergency ad-
dress (F4 to F7). In the same way, when the second error occurs,
the data corresponding to the error is written in the second emer-
gency address (F8 to FB).
Finally, when the last error occurs, the data corresponding to the
error is written in the last emergency address (FC to FF).
Note:
After completing adjustments, be sure to initialize the data
of addresses F4 to FF to “00”.
of addresses F4 to FF to “00”.
Initializing method:
Order Page Address Data
Procedure
1
0
01
01
2
3
01
37
Press PAUSE button.
3
3
02
Check the data changes to
“00”.
“00”.
4
0
01
00
6-73
DCR-HC21
4-1.
EMG Code (Emergency Code)
Codes corresponding to the errors which occur are written in C
page, addresses F4, F8 and FC . The type of error indicated by the
code are shown in the following table.
page, addresses F4, F8 and FC . The type of error indicated by the
code are shown in the following table.
Code
Emergency Type
00
No error
10
Loading motor emergency during loading
11
Loading motor emergency during unloading
22
T reel emergency during normal rotation
23
S reel emergency during normal rotation
24
T reel emergency (Short circuit between S reel
terminal and T reel terminal)
terminal and T reel terminal)
30
FG emergency at the start up of the capstan
40
FG emergency at the start up of the drum
42
FG emergency during normal rotation of the drum
Click on the first or last page to see other DCR-HC21 (serv.man2) service manuals if exist.