Sony DCR-HC15 (serv.man2) Service Manual ▷ View online
1-1
SEÇÃO 1
NOTA DE SERVIÇO
DCR-HC15
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
Cut and remove the part of gilt
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
which comes off at the point.
(Take care that there are
some pieces of gilt left inside)
When remove a connector, don't pull at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector.
Be in danger of the snapping of a wire.
Be in danger of the snapping of a wire.
1-1. NOTA DE SERVIÇO
1.
NOTE FOR REPAIR
1-2E
DCR-HC15
2.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.
Use the AC power adaptor (AC-L10, AC-VQ800 etc.).
Method 2.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
3.
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1
Remove the cabinet R cover.
2
Remove the F panel section.
3
Remove the cabinet R section.
4
Remove the BT panel/EVF section.
5
Remove the VA-118 board and Lens section.
6
Remove the VC-311 board and Mechanism deck.
7
Remove the MD frame assembly from the VC-311 board and Mechanism deck.
8
Disconnect the flexible board from CN2502 of VC-311 board.
9
Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
CN2502
DC power supply (+4.5Vdc)
VC-311 board
Loading motor
VC-311
Disconnect the flexible board
from CN2502 of VC-311board.
from CN2502 of VC-311board.
DCR-HC15
2-1
2-2
2-1. DESMONTAGEM
The following flow chart shows the disassembly procedure.
C
A
D
C
E
E
A
B
B
C
C
C
C
C
E
E
E
E
C
E
E
F
F
E
C
C
E
C
E
E
C
D
D
C
C
C
C
C
B
D
B
E
F
PD-188
PD-188
VC-31
1
VC-31
1
VA-1
18
Screw
M1.7x4
3-989-735-81
Screw
M1.7x6
3-056-030-81
Tapping Screw
M1.7x5
3-713-791-11
Screw
M1.7x2.5
3-989-735-01
Tapping screw
M1.7x3.5
3-713-791-51
Silver
Black
Screw
1.7x3.5
3-989-735-71
4
2
3
1
1
1
2
1
Two screws (M1.7x2.5) black
2
Eye cup (40) assembly
1
Two screws (M1.7x6) black
2
Screw (M1.7x3.5) silver
3
Open the LCD panel
4
Two screws (M1.7x3.5) silver
5
Raise the Finder
1
Screw (M1.7x4) black
2
Screw (M1.7x4) black
3
Open the cassette lid
4
Screw (M1.7x4) black
6
Screw (M1.7x3.5) silver
7
Close the LCD panel
8
Two craws
9
Three craws
q;
Cabinet R cover
1
Two screws (M1.7x4) black
2
Two tapping screws (M1.7x5) black
3
Four craws
4
P cabinet (C) assembly
1
2
3
7
8
1
2
3
4
5
6
8
7
9
q;
4
5
6
5
Two screws (M1.7x4) black
6
Craw
7
FP-621 flexible board (36P)
8
F panel section
1
Screw (M1.7x4) black
2
Three screws (M1.7x4) black
3
Three screws (M1.7x4) black
4
FP-618 flexible board (16P)
5
Harness (PV-140) (20P)
6
Cabinet R section
1
Two screws (M1.7x4) black
2
Cabinet L assembly (40E)
3
FK flexible retainer
4
Screw (M1.7x4) black
5
Remove the Harness of the
Control switch block (FK-CX4000)
from the Flexible cover
6
Control switch block
(FK-CX4000)
7
Sheet Z
8
Two screws (M1.7x2.5) black
9
JK-242 board,
FP-625 flexible board
1
Tape (A)
2
Harness (PV-140) (4P)
3
FP-626 flexible board (6P)
4
Two tapping screws (M1.7x5)
5
Cabinet R section
6
Two tapping screws (M1.7x5) black
7
Two screws (M1.7x4) black
8
Four craws
9
P cabinet (C) assembly
q;
Harness (PV-140) (20, 4P)
qa
Hinge section
qs
P cabinet (M) (40) assembly
qd
LCD insulating sheet
qf
PD-188 board,
LCD unit (ACX307AKM-J),
Light guide plate block
1
Screw (M1.7x4) black
2
Two screws (M1.7x4) black
3
Battery terminal board (3P)
1
Control switch bock (FK-CX4000) (3P)
2
Two screws (M1.7x2.5) black
3
B to B connector (100P)
4
VA-118 board, FP-621 flexible board
5
Lens device LSV-650E (24P)
6
Tape (A)
7
FP-623 flexible board (14P)
8
Screw (M1.7x2.5) black
9
Screw (M1.7x2.5) black
q;
Lens section
1
Control switch bock (FK-CX4000) (12P)
2
FP-625 flexible board (16P)
3
Three screws (M1.7x2.5) black
4
Open the cassette lid
5
Screw (M1.7x4) black
6
Screw
7
Mechanism deck, VC-311 board
1
Three tapping screws (M1.7x3.5) black
2
Two screws (M1.7x2.5) black
3
Two screws (M1.7x2.5) black
4
Eject knob
5
Cabinet (G) assembly
Flexible
cover
cover
1
2
3
4
6
5
1
2
3
4
1
2
3
4
5
7
q;
9
8
1
3
2
3
4
5
1
2
3
3
7
8
9
4
6
1
2
5
4
5
6
7
6
5
1
2
4
q;
qa
8
8
7
9
6
5
3
qd
qs
qf
4
FP-619 flexible board (20P)
5
BT panel/EVF section
SEÇÃO 2
DESMONTAGEM
2. DESMONTAGEM
DCR-HC15
2-3
2-4
2-2. POSIÇÃO DE SERVIÇO
A
B
B
B
C
C
C
C
C
C
C
C
C
C
E
E
VA-1
18
E
E
E
C
C
F
E
C
C
E
C
VA-118 board
CN5402
CN4002
CN1002
CN1004
CN4602
CN4004
VA-118
VC-311
JK-242
1
1
8
9
16
16
VC-311 board
Adjustment remote
commander (RM-95)
commander (RM-95)
LANC jack
MA-421 board
JK-242 board
AUDIO/VIDEO jack
F panel section
AC power
adaptor
adaptor
Monitor TV
AC IN
CPC-7 jig
(J-6082-382-A)
(J-6082-382-A)
DC-IN jack
Power harness
Control switch block (FK-CX4000)
To eject the cassette, connect
the control switch block (FK-CX4000)
the control switch block (FK-CX4000)
Mechanism deck
[SERVICE POSITION TO CHECK THE VTR SECTION]
Connection to Check the VTR Section
To check the VTR section, set the VTR to the Forced VTR power ON mode.
Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).
Connection to Check the VTR Section
To check the VTR section, set the VTR to the Forced VTR power ON mode.
Operate the VTR functions using the adjustment remote commander (with the HOLD switch set in the OFF position).
Setting the Forced VTR Power ON mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 02, and
press the PAUSE button of the adjustment remote
commander.
commander.
Exiting the Forced VTR Power ON mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press
the PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: D, address: 10, set data: 00, and press
the PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
Extension cable (100P)
(J-6082-352-A)
(J-6082-352-A)
1
2
3
7
8
9
q;
4
5
6
1
2
3
4
5
6
8
7
1
2
3
4
6
5
1
2
3
4
5
1
2
3
4
5
7
q;
9
8
6
1
3
2
3
4
5
6
7
1
2
3
4
5
3
7
8
9
4
6
1
2
5
Click on the first or last page to see other DCR-HC15 (serv.man2) service manuals if exist.