Sony DCR-HC1000 / DCR-HC1000E (serv.man2) Service Manual ▷ View online
1-2
DCR-HC1000/HC1000E
2.
POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
that the unit cannot operate.
This following two methods are available to prevent this. Take note of which to use during repairs.
Method 1.
Use the AC power adaptor.
Method 2.
Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the “ADJ” side.
3.
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1
Remove the grip block section, cabinet (L).
2
Remove the grip block section from the cabinet (L).
3
Remove the grip (bottom) cabinet from the grip block section.
4
Remove the grip (R) cabinet assembly from the grip block section.
5
Remove the grip hinge assembly from the grip block section.
6
Disconnect CN2502 (27P, 0.3mm) of RP-241 board.
7
Open the cassette lid.
8
Supply +4.5V from the DC power supply to the loading motor and unload with pressing the cassette compartment.
ENGLISH
JAPANESE
ENGLISH
JAPANESE
Loading motor
DC power supply
(+ 4.5Vdc)
(+ 4.5Vdc)
Disconnect the flexible board
from CN2502 of RP-241 board
from CN2502 of RP-241 board
CN2502
RP-241 board
1-3
DCR-HC1000/HC1000E
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1 k
Ω
/1 W
Wrap insulating tape
Power supply capacitor (C5605)
ST-106 board
LN5604 (+)
LN5603 (-)
Short jig
(1k
(1k
Ω
/1W)
4.
DISCHARGING OF THE FLASHLIGHT POWER SUPPLY CAPACITOR
The power supply capacitor (ST-106 board C5605) of the flash unit is charged up to the maximum 300V potential.
There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged
voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be
discharged as described below.
There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged
voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be
discharged as described below.
4-1.
PREPARING THE SHORT JIG
To preparing the short jig. a small clip is attached to each end of a resistor of 1k
Ω
/1W (1-215-869-11).
Wrap insulating tape fully around the reads of the resistor to prevent electric shock.
4-2.
DISCHARGING THE CAPACITOR
1
Remove the cabinet (L) assembly and the grip assembly.
2
Remove the MS-220 board.
3
Remove the VC-366 board.
4
Remove the JK-271 board.
5
Remove the DB-017 board.
6
Remove the center frame.
7
Remove the lens assembly.
8
Remove the Battery holder and the EVF block.
9
Short-circuit between LN5604(+) and LN5603(-) of the ST-106 board with short jig about 10 seconds.
1-4
DCR-HC1000/HC1000E
ENGLISH
JAPANESE
ENGLISH
JAPANESE
1-2. SELF-DIAGNOSIS FUNCTION
1.
SELF-DIAGNOSIS FUNCTION
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder, or LCD
screen what to do. This function consists of two display; self-
diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
function starts working, and displays on the viewfinder, or LCD
screen what to do. This function consists of two display; self-
diagnosis display and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
2.
SELF-DIAGNOSIS DISPLAY
When problems occur while the unit is operating, the counter of the
viewfinder or LCD screen consists of an alphabet and 4-digit number,
which blinks at 3.2Hz. This 5-character display indicates the
“repaired by:”, “block” in which the problem occurred, and “detailed
code” of the problem.
viewfinder or LCD screen consists of an alphabet and 4-digit number,
which blinks at 3.2Hz. This 5-character display indicates the
“repaired by:”, “block” in which the problem occurred, and “detailed
code” of the problem.
Note:
The “self-diagnosis display” data will be kept even if the lithium battery (BT1001 of FP-953 flexible board) is removed.
1 1
3 1
C
Repaired by:
Refer to page 1-5.
Self-diagnosis Code Table.
Self-diagnosis Code Table.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
Block
Detailed Code
Blinks at 3.2Hz
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
H : Corrected by dealer
E : Corrected by service
engineer
Viewfinder or LCD screen
C : 3 1 : 1 1
1-5
DCR-HC1000/HC1000E
ENGLISH
JAPANESE
ENGLISH
JAPANESE
3.
SELF-DIAGNOSIS CODE TABLE
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
E
E
E
E
E
E
Block
Function
0
4
2
1
2
2
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
1
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
2
0
6
1
6
1
6
2
6
2
9
1
Detailed
Code
0
0
0
0
0
0
1
0
1
1
2
0
2
1
2
2
2
3
2
4
3
0
4
0
4
2
1
0
1
1
2
0
2
1
2
2
2
3
2
4
3
0
4
0
4
2
0
0
0
0
1
0
0
0
0
1
0
1
Symptom/State
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does not
complete within specified time
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
complete within specified time
T reel side tape slacking when unloading.
Winding S reel fault when counting the
rest of tape.
rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum.
FG fault during normal drum operations.
LOAD direction loading motor time-
out.
out.
UNLOAD direction loading motor
time-out.
time-out.
T reel side tape slacking when
unloading.
unloading.
Winding S reel fault when counting the
rest of tape.
rest of tape.
T reel fault.
S reel fault.
T reel fault.
FG fault when starting capstan.
FG fault when starting drum
FG fault during normal drum
operations
operations
Data on A page or D page are rewriten.
Difficult to adjust focus
(Cannot initialize focus.)
(Cannot initialize focus.)
Zoom operations fault
(Cannot initialize zoom lens.)
(Cannot initialize zoom lens.)
Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)
(With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)
(With yaw angular velocity sensor output
stopped.)
Abnormality when the power supply
capacitor of the flash unit is being
charged.
capacitor of the flash unit is being
charged.
Self-diagnosis Code
Repaired b
y
:
Correction
Use the info LITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
operations from the beginning.
Make data on A page and D page correct value.
Inspect the lens block focus MR sensor (Pin wg, wh of CN1010 of
VC-366 board) when focusing is performed when the focus ring is
rotated in the focus manual mode, and the focus motor drive circuit
(IC5102 of VC-366 board) when the focusing is not performed.
VC-366 board) when focusing is performed when the focus ring is
rotated in the focus manual mode, and the focus motor drive circuit
(IC5102 of VC-366 board) when the focusing is not performed.
Inspect the lens block zoom MR sensor (Pin wd, wf of CN1010 of
VC-366 board) when zooming is performed when the zoom lever
is operated and the zoom motor drive circuit (IC5102 of VC-366
board) when zooming is not performed.
VC-366 board) when zooming is performed when the zoom lever
is operated and the zoom motor drive circuit (IC5102 of VC-366
board) when zooming is not performed.
Inspect pitch angular velocity sensor (SE520 of SE-149 board)
peripheral circuits.
peripheral circuits.
Inspect yaw angular velocity sensor (SE521 of SE-149 board)
peripheral circuits.
peripheral circuits.
Checking or replacement of the flash unit.
Click on the first or last page to see other DCR-HC1000 / DCR-HC1000E (serv.man2) service manuals if exist.