Sony DCR-DVD7 / DCR-DVD7E (serv.man2) Service Manual ▷ View online
2-9
2. DISASSEMBLY
2. DISASSEMBLY
DCR-DVD7/DVD7E
AC power
adaptor
AC IN
DC-IN
FP-208 flexible board
FP-209 flexible board
Extension cable(10p)
(J-6082-572-A)
(J-6082-572-A)
Flexible board (10p)
(
(
from the Mechanism deck
)
Flexible board (51p)
(
(
from the Mechanism deck
)
LD-183 board
JK-286 board
S451: cabinet (rear) open switch
(Note)
S452: cabinet (rear)
open switch
open switch
(Note)
A/V jack
DC-IN jack
DI-092 board
DA-036 board
CN1007
CN4101
CN1009
Cushion
Cushion
CN4013
CN1002
VC-410 board
CN8505
CN4801
CN5501
VC-410
[SERVICE POSITION TO CHECK THE DVD DRIVE SECTION]
Connection to Check the DVD drive section
Connection to Check the DVD drive section
To check the DVD drive section, set the DVD drive to PLAY mode. (Set PLAY/EDIT mode by using the power switch
or set forced PLAY mode by using the adjustment remote commander.)
Operate the DVD drive using the adjustment remote commander (with the HOLD switch set in the OFF position).
or set forced PLAY mode by using the adjustment remote commander.)
Operate the DVD drive using the adjustment remote commander (with the HOLD switch set in the OFF position).
Note:
Removing the FP-209 flexible board means removing the LID OPEN switch and the dew sensor. Therefore the
DVD drive section will not move even if the forced PLAY mode is set up. By using am adresive tape, hold down
the two open switches (S451,S452)
the two open switches (S451,S452)
Setting the forced PLAY mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: A, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: A, address: 10, set data: 02, and press the
PAUSE button of the adjustment remote commander.
Exiting the forced PLAY mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: A, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
2) Select page: 0, address: 10, and set data: 00.
3) Select page: A, address: 10, set data: 00, and press the
PAUSE button of the adjustment remote commander.
4) Select page: 0, address: 01, and set data: 00.
DI-092
DA-036
Monitor TV
Adjustment remote
commander (RM-95)
commander (RM-95)
A/V
Video (Yellow)
Multi cable for service
(J-6082-535-A)
2-10
2. DISASSEMBLY
2. DISASSEMBLY
DCR-DVD7/DVD7E
2-3. CIRCUIT BOARDS LOCATION
NAME
FUNCTION
CCD IMAGER
DEW SENSOR, SW, VC-FK RELAY
EJECT, SW/MOTOR
FP203-FP204 RELAY
MULTI/USB CONNECTOR, DC JACK
LENS DRIVE
DEW SENSOR, SW, VC-FK RELAY
EJECT, SW/MOTOR
FP203-FP204 RELAY
MULTI/USB CONNECTOR, DC JACK
LENS DRIVE
LD_VC RELAY
AV I/O, AD/DA, DC IN, CHARGE, CONNECTOR
HI CONTROL, DC/DC CONVERTER, CONNECTOR
AV I/O, AD/DA, DC IN, CHARGE, CONNECTOR
HI CONTROL, DC/DC CONVERTER, CONNECTOR
CONNECTOR, LI BATTERY, PD-SW RELAY
BATTERY, MIC
REMOCON IN, DA-SE RELAY
VC-FP210 RELAY
REMOCON IN, DA-SE RELAY
VC-FP210 RELAY
RGB DRIVE, LED SW, TP I/F
YAW/PITCH SENSOR, SPEAKER
BL DRIVE, SW, PS RELAY
TIMING GENERATOR, TUNE AMP, CAMERA A/D CONV., VIDEO SIGNAL PROCESS,
DVD SYSTEM PROCESS, 256M/128M SDRAM, 64M FLASH ROM, CAMERA CONTROL,
REC/PB RF AMP, DSP, SHOCK SENSOR AMP, SDRAM, MECHA CONTROL CPU,
16M FLASH MEMORY, MECHA DRIVE, CONNECTOR
YAW/PITCH SENSOR, SPEAKER
BL DRIVE, SW, PS RELAY
TIMING GENERATOR, TUNE AMP, CAMERA A/D CONV., VIDEO SIGNAL PROCESS,
DVD SYSTEM PROCESS, 256M/128M SDRAM, 64M FLASH ROM, CAMERA CONTROL,
REC/PB RF AMP, DSP, SHOCK SENSOR AMP, SDRAM, MECHA CONTROL CPU,
16M FLASH MEMORY, MECHA DRIVE, CONNECTOR
FP-154
FP-154
FP-209
FP-209
PD-253
PD-253
FP-204
FP-204
SE-159
SE-159
FP-210
FP-210
CK-150
CK-150
LD-183
LD-183
FP-203
FP-205
FP-205
FP-203
FP-155
FP-155
FP-208
FP-208
VC-410
VC-410
JK-286
JK-286
DA-036
DA-036
DI-092
SW-444
SW-444
DI-092
2-11E
2. DISASSEMBLY
2. DISASSEMBLY
DCR-DVD7/DVD7E
2-4. FLEXIBLE BOARDS LOCATION
The flexible boards contained in the mechanism deck.
FP-157
CONTROL SWITCH BLOCK
(FK13100)
(FK13100)
CONTROL SWITCH BLOCK
(PS13100)
(PS13100)
HELP
DCR-DVD7/DVD7E
HELP
Disassembling and assembling procedures that require attention are described here.
HELP 01
HELP 02
Flexible board (from Mechanism deck)
1
OP blind frame
2
Flexible board
(from the control switch block (FK13100))
3
Tapping screw (M1.7x3.5) black
4
Eject section
5
OP blind frame
Click on the first or last page to see other DCR-DVD7 / DCR-DVD7E (serv.man2) service manuals if exist.